displayit Flare User manual

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 1
Parts List
8 - Frame Perimeter Pieces
(See Diagram 1 for details)
4 - Flat Connecting Plates with Wing Nuts
4 - Corner Connecting Plates with Wing Nuts
4 - Extra Wing Nuts
(1/4-20 Thread Size)
1 - Vertical Support Set
(Set includes two poles and a plastic lock tube)
1 - Flare Spacing Ruler
3 - Double-Sided Curtain Lights
3 - Power Supplies (100 Watts)
16 - Light Mount Clips*
1 - 10 Foot Power Cord with 5 Quick-Connects
4 - Wire Management Clips
2 - Flare Feet
6 - T-Bolts for Flare Feet*
6 - Washer Wing Nuts for Flare Feet*
(1/4-20 Thread Size)
* Includes extras provided
Need Help?
Scan the QR code or go to
displayit.com/flare-guide
to watch an assembly video.

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 2
CAUTION:
METAL EDGES
MAY BE SHARP
Velcro for Power Supplies
Foot Holes Foot Holes
Diagram 1
46” SIDE
CORNER
46” TOP
CORNER
46” TOP
CORNER
46” SIDE
CORNER
46” SIDE
CORNER
46” SIDE
CORNER
46” BOTTOM
CORNER
46” BOTTOM
CORNER
Wire Pass-through
Support Pole
Location
2. Assemble frame top,
bottom, and sides using
four flat connecting plates.
Hand tighten wing nuts to
secure.
3. Assemble perimeter of
frame with four corner
connecting plates.
Note: It’s best to build the frame laying on its back.
HorizontalHorizontal
Vertical
Vertical
1. Upack the frame. Save all foam pieces for repacking later. Lay out the frame pieces as seen in Diagram 1.
Frame perimeter pieces are labeled with stickers matching Diagram 1 to make this step easier.
Take note where the velcro strips for the power supplies are located on Diagram 1.
Assemble the frame on its back.

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 3
8’(92” x 92”) Flare
CurtainLight Spacing Ruler
Flarev.2.0 11/1/2016
Directions:
1.Alignthe green lines with the foot holes in the bottom of the frame.
2.Attachsupport pole in the designated area marked on the ruler.
3.Connectthe bottom of the curtain lights to the center channel of the frame with light clips where noted.
4.Carefullyunroll the curtain lights and attach with the top clips, keeping the wires straight.
5.Attachpower supplies in the designated areas marked on the ruler.
Seepaperinstructions for more detailed instructions.
100Watt Power Supply 100Watt Power Supply 100Watt Power Supply
Support
Pole
FOOTHOLES
FOOTHOLES
CurtainLight
CurtainLight Clip CurtainLight Clip
CurtainLight
CurtainLight Clip CurtainLight Clip
CurtainLight
CurtainLight Clip CurtainLight Clip
DONOT DISCARD
4. Unroll the included spacing ruler and
place it on the ground inside the frame.
Align the green lines on the ruler to the
foot holes in the frame. Use the ruler to
locate the recommended placement for
the support pole, curtain lights, and
power supplies.
5. Install the suport pole as noted on the ruler (Diagram 2).
A. Hook top hook into frame channel and swing down to vertical.
B. Repeat for the bottom pole until they meet in the middle.
C. Press the push-button and slide the lock tube over the end of the
other pole half until the button clicks.
Press
Slide
Lock Tube
Lock Tube
6. Attach the bottom of the curtain to the center
channel of the frame using light clips (Diagram 3).
To attach clips, hook each clip through the wire loop.
Squeeze clip, insert into channel, and release.
Suggested light clip locations are marked on the ruler.
Carefully unroll the curtain light and clip the top clips
into the top of the frame, keeping the wires straight.
Center Channel
Pole with push-button
and tube lock
Pole without tube lock
Spacing Ruler
Top of Frame Bottom of Frame
Diagram 2
Diagram 3

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 4
7. Attach the power supplies to the frame via the velcro
strips and connect the wires to the curtain lights.
7. Attach feet using t-bolts and wing nuts.
Each t-bolt goes through a counterbored hole in the foot, then
through a hole in the metal frame. Secure with a washer wing nut.
Hand-tighten until snug; do not over-tighten.
8. Carefully stand the display up.
Counterbored holes
7. To help stop wire shadows on the graphic, use
the provided snap-on wire management clips.
The curtain light clips may also be used for wire
management.
6. Run the main power cables through the wire
pass-through and connect to the power supply.
Plug the cables into an AC outlet to test the lights.

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 5
1. Using at least two people,
carefully stand the display up.
Starting in top-left corner, turn
and tuck graphic and silicone
into the channel. (#1 on diagram)
Use your fingertip (not fingernail)
for installation.
Note: For large frames, a step ladder
may be required for graphic installation.
2. Work across the top, tacking the graphic into the channel
every two to three feet. (#2 on diagram)
3. Tuck top, right corner into channel. (#3 on diagram)
4. Tuck remainder of top edge of graphic into top channel.
(#4 on diagram)
5. Inspect graphic for hard fold lines in the fabric.
If desired, smooth them out using a fabric steamer.
6. Tuck bottom two corners. (#6 on diagram)
7. Tack middle of sides. (#7 on diagram)
8. Working from top to bottom, tuck remaining silicone in
on both sides. (#8 on diagram)
9. Tack middle of bottom. (#9 on diagram)
10. Tuck remaining bottom edge, working from outside to
inside. (#10 on diagram)
11. Repeat installation steps for fabric on back of frame.
1 2 2 2 3
6 6
77
44
91010
88
Fabric
Graphic
Silicone Welt
(On Back)
Graphic Installation
Silicone
Silicone
Fabric
Fabric
Top of Frame
Caution! Installing silicone-edged graphics is techniqe sensitive;
Practice will shorten installation time.
Handle graphics with care with clean hands in a clean environment.
Cloth or latex gloves recommended.
Keep graphics away from sharp objects.

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Flare v2.0 Updated 11/22/2016
Assembly Instructions Page 6
Packing Instructions
Failure to follow packing instructions
may result in damaged items.
!
Frame perimeter metal pieces with foam between
Vertical Support Pole & Curtain Lights
Power Supplies
Wires &
Small
Hardware Feet
(Between boxes)
1. Carefully lay two curtain lights on
top each other and roll them up
together. Wrap foam around the roll.
Roll up the third curtain light and
wrap with foam.
2A. Insert the vertical support
pole into the large box.
2B. Insert one double curtain roll
into the bottom of the box.
2C. Put the third curtain roll in the
top of the box.
3. Small hardware stores in
the canvas bag.
Two curtain lights stacked
4. Frame perimeter pieces
pack on their edge with foam
between.
6. After all hardware is in the case, put
a foam sheet on top.
7. Fold the graphics up and place them
into plastic bags on the top level.
Fabric Graphics
Bottom Layer Top Layer
Foam Layer
Short foam
on ends