HBF Furniture Cityscape 2.0 User manual

1HBF
Cityscape 2.0
Installation Instructions

2HBF
TOOLS REQUIRED
POWER DRIVER/DRILL 4MM ALLEN WRENCH
8MM ALLEN WRENCH

3HBF
STANDARD MODEL LEG ATTACHMENT
PLACE UNIT ON ITS BACK AND ATTACH LEGS
AS SHOWN BELOW.
• (16) ¼-20 x 23mm Ultra Low Profile Socket Head
Bolt. (4) Bolts per leg assembly
• (4) Leg Assembly
Legs Positioned in corners as shown
This attachment process
Works for the following
Models:
HLD421-011 HLD421-041
HLD421-012 HLD421-042
HLD421-013 HLD421-043
HLD421-021 HLD421-044
HLD421-022
HLD421-023

4HBF
PENTAGON LEG ATTACHMENT
PLACE UNIT ON ITS BACK AND ATTACH LEGS
AS SHOWN BELOW.
• (20) ¼-20 x 23mm Ultra Low Profile Socket Head Bolt
• (3) 120 deg leg assembly
• (2) 90 deg leg assembly
This attachment process
works for the following
models:
HLD421-014
HLD421-024
HLD421-034
Legs Positioned in corners as shown
OPTIONAL LEG ATTACHMENT
ON PAGE “5”

5HBF
PENTAGON OPTIONAL LEG ATTACHMENT
• (20) ¼-20 x 23mm Ultra Low Profile Socket
Head Bolt
• (2) 120 deg leg assembly
• (3) 90 deg leg assembly
OMIT this 120 deg leg (red)
and assemble 90 deg (black)
leg as shown
Assemble this 90 deg
leg as shown (black)
This attachment process
allows for all legs to be in
alignment along all backs
in the direction of the
configuration being created.

6HBF
CITYSCAPE 2.0 TABLE ASSEMBLY
AND LEG ATTACHMENT
• (8) ¼-20 x 15mm Ultra Low Profile Socket
Head Bolt
• (2) Table Pedestals
• (2) Round Attachment Plates
• (2) ½-13 Steel Hex Head Bolts
STEP 1
Table Top Assembly
Using (8) 15mm bolts, attach pedestal
to the upper table top in the manner
shown.
PLEASE DO NOT OVER-TORQUE BOLTS.
Carefully align both pedestals with the
large holes in the lower table top, insuring
that the back edges of both tops are parallel.
Attach round attachment plates to each
pedestal with the ½-13 bolts and fully
tighten.
This assembly process works
for the following models:
HTD42101-3231 HTD42101-5931
HTD42102-3231 HTD42102-5931
HTD42103-5931
Continued on page 7
THIS TABLE ASSEMBLY REQUIRES THE
ATTACHMENT OF ADJACENT UNITS. ONE ON
EACH SIDE. IT IS NOT A STAND ALONE UNIT

7HBF
CITYSCAPE 2.0 TABLE ASSEMBLY
AND LEG ATTACHMENT
• (8) ¼-20 x 15mm Ultra Low Profile Socket
Head Bolt
• (2) Right Leg Assemblies
• (2) Left Leg Assemblies
STEP 2
Leg Assembly
Using (8) 15mm bolts, attach leg assemblies
as shown. Snug bolts just enough to be able
to adjust legs after adjacent units are attached
(page 8).
Once adjacent units are attached and aligned,
fully tighten bolts
PLEASE DO NOT OVER-TORQUE BOLTS.
This assembly process works
for the following models:
HTD42101-3231 HTD42101-5931
HTD42102-3231 HTD42102-5931
HTD42103-5931

8HBF
TABLE AND ADJACENT UNIT ASSEMBLY
• Place assembled table on its back.
• Place adjacent units on their backs. If leg assemblies have not been installed, do not install the leg
assemblies that will be replaced by the table leg assemblies. If leg assemblies have been installed,
remove leg assemblies (red leg assemblies).
• Slide adjacent units into position and reuse the 23mm bolts to attach the units to the table.
• Carefully place the assembled unit in its upright position.
This assembly process works
for the following models:
HTD42101-3231 HTD42101-5931
HTD42102-3231 HTD42102-5931
HTD42103-5931

9HBF
TABLE AND ADJACENT UNIT ASSEMBLY
• Assemble the 4 corner table legs (snug only).
• This assembly requires the purchase of a ganging kit (HAD421-010)(Sold separately). The leg with the angled bracket will not be
used.
• If chair leg assemblies have not been installed, do not install the leg assemblies that will be replaced by the table leg assemblies. If
leg assemblies have been installed, remove leg assemblies (red leg assemblies). Assemble each of the adjacent units using the
ganging legs from the ganging kit as shown. Then attach the table center support legs to each of the adjacent units (leave loose).
Carefully slide the adjacent units to the table and, re-using the 23mm bolts from the previous legs, assemble to the table and tighten
all 23mm bolts. When tightening the 15mm bolts use caution to not over-torque bolts.
This assembly process works
for the following table models:
HTD42101-5931
HTD42102-5931
HTD42103-5931
HLD421-021 HLD421-021
HLD421-011 HLD421-011
POSSIBLE CONFIGURATION

10HBF