Divitec XIN-VC-0622 User manual

Please read this manual thoroughly before use, and keep it handy for future reference.
Instruction Manual
ALL-IN-ONE CAMERA
COLOR CCD
WEATHERPROOF
AF D&N ZOOM CAMERA

- ii -
LIMITATION OF LIABILITY
THE INFORMATIONIN THIS PUBLICATION IS BELIEVEDTO BEACCURATE IN
ALL RESPECTS, HOWEVER,WE CANNOTASSUME RESPONSIBILITY FORANY
CONSEQUENCES RESULTINGFROM THE USETHEREOF. THE INFORMATION
CONTAINED HEREINIS SUBJECT TO CHANGE WITHOUTNOTICE. REVISIONS
OR NEW EDITIONSTO THIS PUBLICATION MAYBE ISSUED TOINCORPORATE
SUCH CHANGES.
ISSUE 1 - JUNE 2006

- iii -
WARNINGS AND CAUTIONS:
CAUTION:
CAUTIONCAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall oulet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the
rear panel are for special adjustments by qualified
personnel only.
Do not install the unit in an extremely hot or
humid place or in a place subject to excessive
dust, mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use
strong solvents such as thinner or benzine as
they might damage the finish of the unit.
Retain the original carton and packing
materials for safe transport of this unit in the
future.
Safety ----------------------------------------- Installation -----------------------------------
Cleaning --------------------------------------
PRECAUTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.

- iv -
FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION
AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE
TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN
A RESIDENTIAL AREAIS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
NORME NMB-003 DU CANADA.
WARNING
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.
CE COMPLIANCE STATEMENT
FCC COMPLIANCE STATEMENT

- v -
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
product heat..
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE
BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE
THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY
SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED
TO DO SO.
15. Use Certified/Listed Class 2 power supply transformer only.
thy
IMPORTANT SAFEGUARDS

THIS PAGE INTENTIONALLY LEFT BLANK.
- vi -

- vii -
TABLE OF CONTENTS
1. INTRODUCTION 1
1.1 THE CAMERA FEATURES 1
2. SYSTEM INSTALLATION 2
2.1 PACKAGE CONTENTS 2
2.2 OPERATION REQUIREMENTS 2
3. PARTS NAME 3
3.1 INSTALLATIONS 3
4. CONNECTION 7
4.1 COLOR LEAD WIRE & COLOR DISPLAY LABEL 7
4.2 EXTERNAL DAY/NIGHT CONTROL 8
4.3 RS-485 CONNECTION 8
4.4 EXTERNAL LENS CONTROL 8
4.5 EXTERNAL A/D KEY CONTROL 9
5. CAMERA ADJUSTMENT 10
5.1 OSD MAIN SCREEN 10
5.2 MAIN MENU 11
6. TROUBLESHOOTING AND MAINTENANCE 18
6.1 TROUBLESHOOTING 18
6.2 MAINTENANCE 18
7. SPECIFICATIONS 19
8. DIMENSIONS 20

1. INTRODUCTION
1.1 THE CAMERA FEATURES :
ALL-IN-ONE: Auto-focus camera / Lens / Weatherproof housing
High performance SONY 1/4" Super HAD CCD
242x zooming capability (Optical : 22x / Digital : 11x)
Ultra Sensitivity Minimum illumination of 0.001 lux @F1.6 (low shutter)
Support camera control available
Flexible camera angle setting
Rugged, Compact Specially Designed for installable anywhere
(Indoor/Outdoor, IP 66)
(CAUTION :
Function : - D/N (Day / Night) - Low-SHUT (Digital Slow shutter)
- DIS (Digital Image Stabilize) - WDR (Wide Dynamic Range)
- DNR (Digital Noise Reduction) - AWB (Auto White Balance)
- AE (Auto Exposure) - AGC (Auto Gain Control)
- BLC (Back Light Compensation) - OSD (On Screen Display)
- D-Zoom (Digital Zoom) - NEGA/POSI (Negative / Positive)
- B/W (Black / White) - PIP (Picture In Picture)
- FREEZE (Rear & still picture) - MIRROR (Right, left reverse picture)
Excellent picture quality
Various picture effects
Dual power operation AC 24V / DC 12V
Use Certified/Listed Class 2 power supply transformer only.)
RS-485
- 1 -
The Day & Night AutoFocus Zoom color DSP Camera provides especially for
closed circuit television (CCTV) and security surveillance application.
IMPORTANT : The user of this camera is responsible for
checking and complying with local, state, and federal laws
and statutes concerning the recording and monitoring of
audio signals.

2. SYSTEM INSTALLATION
< Typical System Configuration >
Installation of the camera must be performed by qualified service personnel in
accordance with all local national electrical and mechanical codes must perform
installation of the camera.
Perform the following steps to install the camera.
2.1 PACKAGE CONTENTS
Camera - 1EA
Instruction Manual - 1EA
A/D Remote Controller (option)
2.2 OPERATION REQUIREMENTS
- 2 -
J-BOX
CAMERA.1
MULTIPLEXER
MONITOR CONTROLLER DVR / VCR
RS-485
RS-485
RS-485
VIDEO
CAMERA.2 CAMERA.3 ......
VIDEO

3. PARTS NAME
- 3 -
CAMERA CONTENTS
SUNSHADE
AF D&N CAMERA MODULE
MOUNT BASE
BIMETAL
HEATER
CONNECTION CABLE
CABLE LABEL
POLY BAG
DRILLING GUIDE LABEL
ACCESSORY KIT
MOUNT TORX SCREWS(M6x35.0)(4X)
PLASTIC ANCHORS(4X)
TORX WRENCH(T-20)(1X)
"L" TYPE HEX WRENCH(1X)
Carefully remove the contents from the box, and verity that nothing was damaged
in shipment.
4 Point - Drilling Position
50201623A
3.1 INSTALLATIONS
1. Cable through the wall
with mount base.
2. Using the conduit knockout
punched with the
mount base.
3. Cable through the
junction box with
the mount base.
There are three ways of installing the camera.

- 4 -
3.1.1 INSTALLATION 1 (Cable through the wall with the mount base)
A. Drill the mounting location, using the template sheet (or the bottom of the
mount base) as a template.
B. Insert the plastic anchors into the hole which has just drilled.
C. Connect BNC cable and communication lines.
D. Fit the screw holes of the mount base into the plastic anchors.
E. Screw up the mount screws (T-20).
F.Adjust the camera suitably using the pan & tilt function, and fasten both the
socket set screw (1x) and torx lock screw (2x) to fix the camera.
Socket Set Screw
M5.0, L=5.0mm
Hexagon Wrench
Torx Screws (T-20)
M6.0 x 35.0 (4x)
Wall
Mount Base
Plastic Anchors (4x)
Template Sheet
AB
Torx Lock Screw (T-20)
B
A

- 5 -
3.1.2 INSTALLATION 2 (Using the conduit knockout punched with Mount Base)
A. Drill the mounting location, using the template sheet (or the bottom of the
mount base) as a template.
B. Insert the plastic anchors into the hole which has just drilled.
C. Connect BNC cable and communication lines.
D. Fit the screw holes of the mount base into the plastic anchors.
E. Remove the conduit knockout punched for the cable entry.
F. Screw up the mount screws (T-20).
G. Adjust the camera suitably using the pan & tilt function, and fasten both the
socket set screw (1x) and torx lock screw (2x) to fix the camera.
A conduit knockout punched
for the cable entry
Socket Set Screw
M5.0, L=5.0mm
Plastic
Anchors (4x)
Hexagon Wrench
Torx Screws (T-20)
M6.0 x 35.0 (4x)
Wall
Mount Base
Template Sheet
B
Torx Lock Screw
(T-20)
Cable
A
AB

- 6 -
3.1.3 INSTALLATION 3 (Cable through junction box with mount base)
The camera can be mounted on the junction box using the UNC # 8-32 machine
screws.
Junction Box
Socket Set Screw
M5.0, L=5.0mm
Torx Screws (T-20)
UNC 8-32 x 0.75" (4x)
(not provided)
Hexagon Wrench

4. CONNECTION
CAUTION : Do not connect the power cable until all other connections have been
completed. If you complete the whole connection of cameras, then you have
to cut the extra cable.
4.1 COLOR LEAD WIRE & COLOR DISPLAY LABEL
- 7 -
REMOTE CONTROLLER
FAR
MENU
WIDE
TELE
NEAR
MONITOR
VIDEO(BNC)
RS-485 CONNECTION
Day & Night CONTROL
A/D KEY CONTROL
DVR / VCR
(BLUE)
(GREEN)
(BROWN)
(VIOLET)
(GRAY)
(WHT-BLK)
LENS CONTROL
(BLACK)
(ORANGE)
(RED)
(WHITE)
POWER CONNECTION
COLOR
PINK
SKY-BLUE
BLACK
WHT
RED
WHT-BLK
GRAY
BLUE
GREEN
ORANGE
VIOLET
YELLOW
BROWN
DESCRIPTION
TXD
RXD
GND
AC 24/DC 12
AC 24/DC 12
EXT-OUT
EXT-IN
RS-485(-)
RS-485(+)
A/D KEY
FOCUS
COMMON
ZOOM

4.4 EXTERNAL LENS CONTROL
Connecting to the RS-485 : The Camera can be controlled remotely by an
external device or control system, such as a control keyboard, using RS-485
half-duplex. Connect Market Rx+, Rx- to Tx+ and Tx- of the RS-485 control
system.
4.3 RS-485 CONNECTION
- 8 -
RS-485
RS-485(-)
(BLUE)
RS-485(+)
(GREEN)
ZOOM
TELE(+) : External DC 3V to 12V (BROWN)
: GND (YELLOW)
WIDE(-) : GND (BROWN)
:
External DC 3V to 12V (YELLOW)
FOCUS
NEAR(+) : External Power DC 3V to 12V (VIOLET)
: GND (YELLOW)
FAR(-) : GND (VIOLET)
:
External Power DC 3V to 12V BNC (YELLOW)
FOCUS
ZOOM
COMMON
(YELLOW)
ZOOM
(BROWN)
FOCUS
(VIOLET)
COMMON
(YELLOW)
4.2 EXTERNAL DAY/NIGHT CONTROL
Is connect to an external sensor to receive day/night detection signals.
DAY/NIGHT
EXT-IN
(GRAY)
GND
(BLACK)
*Note: To validate the sensor inputs, select Function menu B/W mode the EXT
EXT-OUT
(WHT-BLK)
DAY : OPEN
NIGHT : CLOSED
External sensor switch ON/OFF
DAY/NIGHT
COLOR
B/W
EXT-OUT
COLOR
B/W
NO
NC

- 9 -
4.5 EXTERNAL A/D KEY CONTROL
External Controller Circuit Schematic
ADKEY2
Remote Controller
1
122
1
122
1
122
1
122
1
122
R22 150
R20 12K
R21 5.6K
Sw10 TELE
R19 22K
Sw11 WIDE
Sw13
FAR
Sw12
NEAR
R18 33K
Sw9 MENU
A/D KEY
A/D KEY
(ORANGE)
Remote Controller
REMOTE CONTROLLER
FAR
MENU
WIDE
TELE
NEAR
1m
3
86mm
40mm
GND
(BLACK) A/D KEY
(WHITE)

HITRON
AEAUTO
AWB
MF
NORMAL
F1.6
0DB
CAM 01
84X
5. CAMERA ADJUSTMENT
5.1 OSD MAIN SCREEN
Camera title.
Status of the auto exposure.
Status of the auto white balance.
Status of the focus mode.
Status of the zoom position, brightness, or sharpness.
Status of the shutter speed.
Status of the iris.
Status of the AGC. (auto gain control)
Camera ID.
- 10 -

5.2 MAIN MENU
- 11 -
<MAIN MENU>
WB
AE
BLC
TITLE
DISPLAY
CAM SET
EFFECT
PRESET
END
1
2
3
4
5
6
7
8
5.2.1 WB (White Balance)
AWB Auto white balance mode.
INDOOR Indoor white balance mode.
OUTDOOR Outdoor white balance mode.
MANUAL Manual mode. You can change R and B Gain manually.
For changing R and B gain, use "NEAR" and "FAR" key.
If you save the change, and push the "MENU" key.
WAWB Wide range auto white balance mode.
<WB>
AWB
INDOOR
OUTDOOR
MANUAL R/B
WAWB
END

5.2.2 AE (Auto Exposure)
AUTO Auto exposure mode. (Iris, Shutter, AGC)
IRIS PRI Iris priority auto exposure mode.
SHUTTER PRI Shutter priority auto exposure mode.
AGC Auto gain control on/off.
MANUAL Manual exposure mode. (Iris, Shutter, and AGC)
LOW-SHUT Display Low-Shutter mode. (Mode can be changed in the
preset menu)
<WE>
AUTO
IRIS PRI
SHUTTER PRI
AGC
MANUAL
END
IRIS
AGC
SHUT
LOWSHUT
5.2.3 BLC (Back Light Compensation)
DEFAULT Default setting. Center weight BLC.
ADJ TOP You can adjust BLC Zone in left and/or top direction.
ADJ BOTTOM You can adjust BLC Zone in right and/or bottom direction.
LEVEL You can adjust BLC level (0 ~ +90)
Default value is 30.
OFF BLC off.
<BLC>
DEFAULT
ADJ TOP
ADJ BOTTOM
LEVEL
OFF
END
- 12 -

- 13 -
CMD
TITLE
<TITLE MENU>
B
C
A
5.2.4 TITLE
A. TITLE
B. Character Table
C. Command Line
: Move to left
: Move to right
< : Erase a left character
> : Erase a right character
S : Save title
E : End
5.2.5 DISPLAY
DISP0 Display title and camera ID.
DISP1 Display title, camera ID and zoom lens position.
DISP2 Display all camera status.
DISP Off, On and push on. (Display on when any key is pressed)
<DISPLAY>
DISP0
DISP1
DISP2
DISP PUSHON
END