dixell XWEB5000 EVO User manual

INSTALLATION GUIDE
Ver 1.0

WARNING: Use only modems supported by this monitoring
unit. Dixell S.p.a can accept no responsibility for
possible damage due the usage of not supported
modems.
WARNING:
Dixell S.p.a. reserves itself the right to alter this
manual without notice. The last version available
can be downloaded from the website.

INDEX
1CHECK LIST.......................................................................................5
2TO DOLIST........................................................................................6
3RS 485 CONNECTION.....................................................................7
3.1 The TTL output...............................................................................9
3.2 Serial address of the instruments................................................9
4Local connection with monitor, mouse and keyboard...............10
4.1 HOW TO SETUP YOUR NETWORK CARD..........................12
4.1.1 Windows 98 and ME TCP/IP Setup.................................12
4.1.2 Windows 2000 TCP/IP Setup ...........................................16
4.1.3 Windows XP TCP/IP Setup...............................................18
5Modem connection (“or point to point connection”)...................23
5.1 HOW TO SETUP a dial-up connection...................................24
5.1.1 Setting up dial-up connection for windows 98................24
5.1.2 Setting up dial-up connection for windows me...............30
5.1.3 setting up dial-up connection for windows 2000............38
5.1.4 SETTING UP dial-up connection for windows XP.........51
6Intranet / ethernet connection.......................................................65

XWEB SERIES InstallationGuide
1592010850 23/05/2007 Pg. 5/72
1CHECK LIST
•The XWEB5000 server unit.
•One power cord for power supply connection.
•2 mounting brackets.
•Quick reference manual (Fast installation).
•One serial line adapter
•One CD Rom containing the Operating manual and software

XWEB SERIES InstallationGuide
Pg. 6/72 23/05/2007 1592010850
2TO DO LIST
•Check if the power supply line matches the XWEB5000
specification (90~264 VAC 50~60Hz.).
•Connect the serial line RS 485 with the adapter provided.
•Plug-in monitor, keyboard and mouse (if required) before turning
on the unit.
•Plug-in RJ 45 network cable (not provided).

XWEB SERIES InstallationGuide
1592010850 23/05/2007 Pg. 7/72
3RS 485 CONNECTION
To be connected to the serial line all the Dixell Modbus instruments
must be provided with direct RS485 terminals or the “TTL”-RS485
interface (XJRS485 or XJ485). Check the instrument manuals for
more information. The RS485 line is mainly based on two polarised
terminals. Please pay respect to the right sequence for all the
devices connected to the serial line.
Follow these important instructions:
•The RS485 serial line must reach all the instruments where they
are installed.
•Make sure of the wire polarities when screwing them into the
instrument terminals.
•The cable must have 2 or 3 wires with shield, minimum section
0,5mm2(eg. the BELDEN 8772).
•From the XWEB5000 position the cable reaches all the
instrument positions.
•Do not execute loops or derivations:

XWEB SERIES InstallationGuide
Pg. 8/72 23/05/2007 1592010850
Right connection:
Wrong connection:
•Always keep the serial cable away from power cables.
•Always keep the serial cable away from Electro-magnetic or
frequency sources.
•Do not connect shield to ground.
•Do not connect the “Gnd (ground)” terminal.
•Remember to draw a map of the line. This will help you to find
errors if something is wrong.
•The instrument with RS485 have “+” and “-“ terminals, respect
the polarity.
•To keep the line balanced it is necessary a 100 Ohm resistor at
the end of the line (you ca use the RS 485+ and RS 485-
terminals of the last instrument connected).

XWEB SERIES InstallationGuide
1592010850 23/05/2007 Pg. 9/72
3.1 The TTL output
The instrument with RS485 on board does not need any kind of
external interface module. For instruments with an external
interface: keep the TTL cable away from power cables or frequency
sources.
The XJ485 external interface must be connected witha TTL cable to
the instrument with TTL compatibility.
3.2 Serial address of the instruments
Each instrument must be defined by its unique address.
Check the address into the Adr parameter value of each
instruments. Take reference to the instruction manual of the
instrument itself to find the right procedure to enter the programming
and set the value.
The easiest way to work with the category functions is to set the
addresses progressively for similar groups of instruments which
have the same application.

XWEB SERIES InstallationGuide
Pg. 10/72 23/05/2007 1592010850
4Local connection with monitor, mouse
and keyboard
On rear of the XWEB5000 sockets are provided for a monitor, a
mouse and a keyboard. Please connect all the peripherals before
powering-on the unit otherwise the system may fails to recognise
them. This means that , for example, if you do not plug the monitor
cable in now, you won’t see anything displayed on it later.
The unit can also work without these three elements therefore if the
user intendsto work just with the remote, he can definitively remove
them after the setup operations. In any case inside the of
XWEB5000 is loaded a standard browser to allow the user setting
up the unit.
If necessary check the instructions manual of each device
connected to the unit.
The operative procedure to work with XWEB5000 is the same for all
connection methods.