DKM Motor DSA Series User manual

Controller Coding System
Specification
Characteristics
Model
Rated volltage
DSA-□□□-□
AC 220~240V 50/60Hz
±10 %
Below 5A
Phase control
Operate with volume
-10C°~ 40C°
35-85%RH
1500VAC 50/60 for 1minute
Over 100MΩ(Base on 500VDC mega)
6W~180W
±5%(Standard)
50Hz : 90~1400r/min
60Hz : 90~1700r/min
D AS D006
DKM Motor
Co., Ltd.
Speed
Controller
Analogue
Type
006 : 6W
010 : 10W
015 : 15W
025 : 25W
040 : 40W
060 : 60W
090 : 90W
120 : 120W
180 : 180W
D : AC220V 60Hz
E : AC 220~240V 50Hz
Ambient
voltage range
Control
·DSA is unit type speed controller.
·It is easy to control the speed of the motor by connector motor and
controller unit as using dedicated connector and by connecting AC
terminal to power source.
·Variable speed range: 50Hz: 90~1400rpm, 60Hz: 90~1700rpm
·When the switch sets to RUN, the motor operates at the set rotation speed
and when the switch sets to STOP, motor stops.
Allowable
current
Range of speed
control
speed
control
Changing rate
of speed
Output
Ambient
temperature
Ambient
humidity
Insulation
resistance
Dielectric
strength
We appreciate you for purchasing products of DKM Motor Co., Ltd.
Before using the product you have purchased, check to make sure
that it is exactly what you ordered. Then, Please use it following the
instructions below.
DKM Motor Co., Ltd.
Head Office / Factory
292, Yeomjeon-ro, Michuhol-gu,
Incheon Republic of Korea 22117
Tel. [phone] Fax. [phone]
DSA Instruction Manual
ANALOGUE SPEED CONTROLLER
CAUTION BEFORE USING
* Before using the product you purchased, make sure that it's exactly what
you ordered.
* Ambient temperature is -10℃ ~ +40℃, ambient humidity is Max. 85%.
Avoid direct ray of light and install a cover.
* Avoid the place in vibration, deep impact, lots of dust, inflammable gas and
corrosive gas.
* Install the motor and controller as closely as possible. (2m or less)
* There is possibility of malfunction in case of parallel connection with controlled
device in high-capacity electric circuit. Please wire line with separate circuit.
*
Make sure to protect the motor shaft. A tube should be on it.
* Do not catch only lead wire when it is carried. It can be snapped.
Safety Informmation
!
!
!
Alerts declared in the manual are classified to Danger,
Warning and Caution by their criticality
There is a danger of occurring electric shock in the input/output terminals so
please never let your body touched to the conductive substance.
* Do not use the product in an explosive or flammable atmosphere. fire may
occur.
* Only qualified installers should be assigned to the work of installation,
connection, running, operation and inspection. This is intended to prevent
fire, electric shock and injury.
* Before starting the work, turn off the speed controller power. Otherwise,
electric shock may occur.
* Be sure to keep power input voltage of the speed controller within the rated
range.
* Electrical connections must be done under strict accordance with the
connection example.Otherwise, fire and electric shock may occur.
* After connection, mount the covers of power connection terminal and
input/output signal connection terminal. Otherwise, fire or electric chock
may occur.
* Do not use the motor and speed controller in excess of ratings.
Otherwise, electric shock, injury of the operator and damage of the
equipment may occur.
* Do not grip the motor output shaft or lead wires. Otherwise, injury may occur.
* Do not place combustibles around the motor and speed controller.
Otherwise, fire may occur.
* Do not put any object into the openings of the speed controller.
Otherwise, fire, electric shock or damage of the equipment may occur.
* Be sure to set the switch to the stop position before connection the power supply.
* The lower RPM setting is, the lower the motor's torque possible to use is.
If the surface temperature of the motor is more than 90 degrees depending
on the operating conditions of the motor, we recommend using at a higher
speed range than the current set speed range.
DANGER
!DANGER
WARNING
!WARNING
CAUTION
!CAUTION
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury
WARNING indicates a potentially hazardous situation
which,if not avoided, could result in death or serious injury
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury

2-M4 BOLT
CONTROLLER
53 +1.0
+0
81 90±0.2
+1.0 +0
PANEL2-M4 or 2-Ø 4.5
Installation
Dimension
How to Use
100
90
60
3.0
(13)
2.5
94
(118.5)
(8.5)
52.5
80.5
2-Ø 4
SPEED VOLUME
'ON'LED
SCALE ADJUST
VOLUME
RUN/STOP
SWITCH
T.G
MOTOR
CCW
T.G
MOTOR
CW
ITEMS LENGTH (L)
DEW0.5M
DEW1.0M
DEW1.5M
DEW2.0M
<EXTENSION CABLE>
CW Direction CCW Direction
2) Fix the controller and front cover with screws and nuts.
<Installation>
1) Connect control unit and lead wire connector of motor.
2) Press stop button before connecting AC power to ④, ⑤ terminals.
3) When AC power input, LED lights on.
4) CW Direction - Connect ② COM, ③ CW / CCW Direction - Connect ② COM, ① CCW
5) When RUN/STOP switch is set to 'RUN' and speed volume is turned to clockwise, the rotation speed of motor will be faster and vice versa.
6) If operate 'RUN/STOP' switch to STOP, motor is stopped. RUN/STOP switch isn't ON/OFF power supply, so install a separate power switch
when stopping the motor for a long time.
0.5m(STANDARD)
1.0m(OPTIONAL)
1.5m(OPTIONAL)
2.0m(OPTIONAL)
1) Make holes on the panel like the drawing.