DKS MicroPLUS 8055 User manual

MODEL 8055 MicroPLUS®RF RECEIVER
Installation
Receiver Terminal Wiring
DoorKing Part Numbers
The model 8055 is a High Security Encrypted “Rotating Code” RF Receiver that is designed ONLY for use with MicroPLUS®transmitters and is
typically installed in automatic garage door openers and vehicular gate operators. The encrypted “Rotating Code” programming in this receiver and
the companion MicroPLUS®transmitters prevent copied transmitter codes from being used again to operate the garage door or gate. The 8055
receiver can store up to 40 MicroPLUS®transmitter codes in its memory.
This receiver is NOT designed to be installed outdoors without being protected from the weather. An outdoor enclosure is available for the
8055-081 receiver if required (P/N 8057-110 - Metal Outdoor Box).
Install the 8055 receiver in a location so the antenna is NOT surrounded by metal and is in free air as high as possible above the ground.
A longer Coax Antenna kit is available for the 8055-081 receiver if required (P/N 1514-073 - Includes antenna, mounting “L” bracket and 15 feet of
coax cable).
120 Glasgow Avenue
Inglewood, California 90301 U.S.A.
123
Built-In
Antenna
#1 Com
#2 Relay
#3 Radio
Power
12-24 Volt
AC or DC
To Receiver Termnal #1 (Neg.)
To Receiver Termnal #3 (Pos.)
To Receiver Termnal #1
To Receiver Termnal #2
To Receiver Termnal #3
12-24 Volt Transformer
P/N 8069-080 P/N 8070-080 P/N 8071-080
From “Low Voltage Common”
From “Radio Open”
From “Circuit Board” Power
1Button 2Button 3Button
Use ONLY MicroPLUS®Transmitters
Garage Door Opener: To connect the 8055
receiver directly to a typical garage door opener,
connect terminals 1, 2 and 3 on the receiver to
terminals 1, 2 and 3 on the garage door opener.
Typical
Garage
Door
Opener
#2 Relay: Normally Open (N.O.) relay
contacts are provided on terminals #1 and #2.
Relay is rated for 30 volts, 1 amp max.
123
To Receiver Termnal #1
To Receiver Termnal #2
To Receiver Termnal #3
Gate
Operator
Polarity Matters!
8055-080
Built-In Antenna
8055-081
Coax Antenna Kit
P/N 8055-080
123
F Connector
Coax Antenna Kit
(Included)
18” Coax Cable
#1 Com
#2 Relay
#3 Radio
Power
12-24 Volt
AC or DC
Receiver Terminal
Receiver Terminal
P/N 8055-081
#1 & #3 Power: Connect 12 - 24 Volt AC or DC
power to terminals #1 and #3.
If DC power is used (Transformer):
Terminal #1 is NEGATIVE and terminal #3 is POSITIVE.
Use minimum 18 AWG wire to power the receiver.

Programming
8055-065-B-8-11 Copyright 2011 DoorKing, Inc. All rights reserved.
Programming Transmitter Codes: Press and hold the programming push button (about 2 seconds) until the programming LED quickly
flashes ONE time, then release the button. The programming LED will flash once every two seconds indicating that you are in the transmitter
programming mode....
....While the programming LED is flashing, activate each of the MicroPLUS®transmitters that will be used (If you are using a two or three button
transmitter, make sure to press the correct button). A maximum of 40 transmitters codes can be stored in this receiver.
Once the desired transmitter codes have been stored into the receiver memory, the receiver will automatically exit the programming mode when no
more transmitter codes are received (approx. 30 seconds idle time). This will be indicated by a series of 10 quick flashes followed by a long flash.
Erase All Transmitter Codes: Press and hold the programming push button until the programming LED quickly flashes ONCE, then TWICE,
then THREE times, then FOUR times for three times in a row (about 12 seconds total for the whole sequence), then release the button. Five
seconds after releasing the button, the LED will emit ONE long flash indicating ALL memory (transmitter codes) have been erased.
120 Glasgow Avenue
Inglewood, California 90301 U.S.A.
This device complies with the FCC Rules Part 15. Operation is subject to the following two conditions:
1.) This device may not cause harmful interference.
2.) This device must accept and interference received, including interference that may cause undesired operation.
This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.
Twice Three Times Four Times Four Times
Three Times in a Row
Four Times One
Long
Flash
One
Long
Flash
10 Quick Flashes
5 Sec.
Release
Button
Release
Button
Once
One Quick Flash
2 Sec.
Press
and
Hold
Button
Press
and
Hold
Button
2 Sec. 2 Sec. 2 Sec. 2 Sec. 2 Sec.
Transmitter Programming Mode
Activate All Desired
MicroPLUS®Transmitters
All Desired
MicroPLUS®Transmitters
have been Activated
2 Sec. 2 Sec. 2 Sec.
Transmitter Programming Mode
Approximately 30 Seconds Idle Time
Approximately 12 Seconds
DoorKing Part Numbers
8055-080
Built-In Antenna
8055-081
Coax Antenna Kit
123
Programming Push Button
Programming LED
FINISH
START