DLS Cruise CRPP-VO2.14 User manual

User manual
VOLVO

DLS Sweden l [email protected] l www.dls.se

Content
Welcome
Warranty
General
Declaration of conformity
Included parts
Pre installation
Mounting info
General door panel dismounting
Installation
Dismount door panel
Change tweeters
Crossover
Reasemble door panel
Cable adaptor
Running-in time
DLS support
Specifications
Impedance vs Frequency
Dimensions
Compatible car models
Product markings
1
1
1
1
2
2
2
3
4
4
6
7
7
8
8
8
9
9
10
11
12
DECLARATION OF CONFORMITY
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-VO2.14/18. For
us, it’s all about the sound experience. We care deeply
about sound and construction quality. In order for your
experience to be as optimal as possible, it is important that
you read this manual, preferably before you start your
installation. Keep the manual in a safe and accessible place
for future reference.
Your tweeters must be installed correctly in order to work as
intended. Make sure you have all necessary tools nearby
before starting and that you are completely confident in how
to proceed. If you feel the slightest uncertainty; feel free to
take the help of an experienced installer or a car audio
dealer.
General
Some sound systems may vary in size of the installed
tweeters. Make sure that your vehicle has the same size as
this tweeter, before you start the assembly.
This is a generic mounting instruction. The approach is
similar to all of the described car models. Some screws and
clips may be placed differently depending on your car
model.
DLS Cruise tweeters for vehicles are manufactu-
red in accordance with the EU directive EEC 95/54
(72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with
the WEEE-directive 2012/19/EC. The products are
also produced in accordance with the EU RoHS
directive 2015/863/EU.
Warranty
This tweeter is covered by warranty, depending on the
conditions in the country where it is sold. If the tweeter is
returned for service, please include the original dated
receipt with the product.
Winn Scandinavia AB
Elementvägen 15 - SE-702 27 Örebro - Sweden
Tel: [phone] - E-mail: [email protected]
www.dls.se
DLS speakers are engineered by DLS Sweden,
a part of:
Designed & Sound tuned in Sweden.
CRPP-VO2.14/18
DLS CRUISE

Included products:
2pcs Tweeters
2pcs Crossovers
Included parts
Pre installation
Included in box:
4pcs Adhesive foams for wrapping
4pcs Terminal crimp connectors
2pcs Tweeter adaptor cable bar ends (marked with TW-A)
2pcs Tweeter adaptor cable (marked with TW-B
1pc Pry tool
1pc Manual
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure the
negative terminal from your battery/power source. This will prevent the risk of
damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from
any possible connection belonging to the battery/power source system.
Mounting info
Some sound systems may vary in size of the door speaker. Make sure that your vehicle has the same
speaker size as this speaker, before you start the assembly
Bolts size can vary between 7 & 8 mm
Torx size can vary between T20 & T25
2

Remove the trim panel by using a PRY tool:
General door panel dismounting
3
This is a generic mounting instruction. The approach is similar to all of the described car models. Some screws and
clips may be placed differently and depending on your car model (see specific car models on the following page).
1
2
Remove the bolts using 7mm hex bit:
3
4
Remove the window control panel using PRY tool.
Unplug the harness:
5
T20/T25 screw is located under the panel.
Remove screw.
6
T20/T25 screw can be seen from under the arm
rest, or there’s a cover that needs to be removed.
Finally. Move the door panel upwards to dismount.
8
7

Dismount the door by removing the cover of the
door panel.
Hint: Use plastic PRY tools to avoid marks on
the panels or damaging the plastic clips.
Dismount door panel
Installation
1
2
3
4
1
1
2
3
4
XC90
1) Remove the cover behind the door handle. Use
PRY tool. Behind the cover are two T20/T25 screw.
Unscrew them. Move the door panel upwards.
Hint: Sometimes it’s easier to remove the window
control panel and unplug the harness, before lifting
up the door panel.
S90/V90
Remove the trim panel by using a PRY tool.
Start at 1) and move towards 2).
Behind the trim panel are two 7mm bolts located.
Remove screw.
3) Remove the window control panel using PRY
tool. Unplug the harness. T20/T25 screw is located
under the panel. Remove screw.
4) T20/T25 screw can be seen from under the arm
rest, or there can be a cover that needs to be
removed.
Move the door panel upwards.
S90/V90
S60/V60
1) Remove the window control panel with PRY
tool.Behind the control panel is one T25 screw
located. Unscrew it. Unplug the harness.
Start by removing the cover by the speakers. Use a
PRY tool.
2) Start in the inside of the cover. Work your way
towards the door handle.
3) Push the trim in the direction of the arrow. (There
is a hook behind the trim)
Behind the trim is a 7mm bolt. Unscrew the bolt.
Unplug the harness.
4) Under the arm rest is one T25 screw. Unscrew it.
Move the door panel upwards.
Remember: Use the PRY tools to avoid
marks on the panels or damaging the
plastic clips.
4

XC60
1) Remove the window control panel with PRY tool.
Behind the control panel is one T20/T25 screw
located. Unscrew it. Unplug the harness.
2) Under the arm rest is one T20/T25 screw.
Remove the cover. Unscrew it.
3) At the bottom of the panel is a 7 or 8mm bolt.
Unscrew it.
Move the door panel upwards.
12
3
XC40
1) At the bottom of the panel are two 7 or 8mm
bolts. Unscrew them.
2) Under the arm rest are two T20/T25 screw.
Unscrew them.
3) Behind the door handle is a rubber cover.
Remove cover and under it is a 7 or 8mm bolt.
Unscrew the bolt.
Move the door panel upwards.
Hint: Sometimes it’s easier to remove the window
control panel and unplug the harness, before lifting
up the door panel.
1
2
3
There are several electric and mechanical
connectors on the backside of the door panel.
Disconnect the cables to the door handle, speaker,
window control and door light.
5

Change tweeters
Remove the tweeter by unscrewing the T20 Torx.
Unplug the speaker harnesses.
Plug in the new tweeter and the crossover, the
connection cable can be used if needed. Use the
OEM screws to fix the new DLS tweeter.
Make sure to use adhesive foam pads to wrap the
crossover to avoid rattle and secure the cross over
to the door panel.
Make sure that the new DLS tweeter is properly
fixed and don’t touch the surrounding plastic.
HINT: DLS recommends adding sound deadning
material on the door panel before the assembling.
6

Reassembly door
The yellow cable loop is tweeter level select, enabling fine tuning of the high frequencies
Closed loop = -4dB (Shown in the picture)
Open loop = Normal
Crossover
4
3
2
1
32
1
3
2
1
4
3
2
1
Connect all plugs to the door cover, reconnect the unlocking device, place the door cover from the top, by the
window seal and push it gently down. Make sure the clips are in place and can engage. Give the door panel
a push by the hand to attach to the clips. Mount and fasten all screws to the correct places. Make sure that no
screws or clips are left over.
Reconnect the battery/power source terminal.
Now it’s time to play some good music and enjoy!
7

Note!
Adaptor cable marked with TW-B shall be used when replacing Bowers & Wilkins or Harman Kardon tweeter.
This adaptor reverse the polarity of the signal to the tweeter.
Cable adaptor TW-B
Running-in time
Allow the speaker to play for at least 15-20 hours in order to perform at its possibly best.
This run-in can be made with tone sweep or with just music.
Start at a moderate volume and increase the volume step by step during the running in
period. After the 15-20 hour run in session the performance and characteristics will be in
the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your
country.You can always contact the DLS Help desk in Sweden at e-mail: [email protected]. Information can also
be found on our WEB- site www.dls.se. We follow a policy of continuous advancement in development. For
this reason, all or part of the specifications and designs may be changed without prior notice.
8