DLS Cruise CRPP-VO2.64 User manual

User manual
VOLVO

DLS Sweden l [email protected] l www.dls.se

Content
Welcome
Warranty
General
Declaration of conformity
Included parts
Pre installation
Mounting info
General door panel dismounting
Installation
Dismount door panel
Change speakers
Reasemble door panel
Running-in time
DLS support
Specifications
Impedance vs Frequency
Dimensions
Compatible car models
Product markings
1
1
1
1
2
2
2
3
4
4
6
7
8
8
9
9
10
11
12
DECLARATION OF CONFORMITY
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-VO2.64/68. For
us, it’s all about the sound experience. We care deeply
about sound and construction quality. In order for your
experience to be as optimal as possible, it is important that
you read this manual, preferably before you start your
installation. Keep the manual in a safe and accessible place
for future reference.
Your speakers must be installed correctly in order to work
as intended. Make sure you have all necessary tools nearby
before starting and that you are completely confident in how
to proceed. If you feel the slightest uncertainty; feel free to
take the help of an experienced installer or a car audio
dealer.
DLS Cruise speakers for vehicles are manufactu-
red in accordance with the EU directive EEC 95/54
(72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with
the WEEE-directive 2012/19/EC. The products are
also produced in accordance with the EU RoHS
directive 2015/863/EU.
Winn Scandinavia AB
Elementvägen 15 - SE-702 27 Örebro - Sweden
Tel: [phone] - E-mail: [email protected]
www.dls.se
DLS speakers are engineered by DLS Sweden,
a part of:
Designed & Sound tuned in Sweden.
CRPP-VO2.64/68
DLS CRUISE
General
Some sound systems may vary in size of the installed
speakers. Make sure that your vehicle has the same size as
this speaker, before you start the assembly.
This is a generic mounting instruction. The approach is
similar to all of the described car models. Some screws and
clips may be placed differently depending on your car
model.
Warranty
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.

Included products:
2pcs Woofer speakers
Included parts
Pre installation
Included in box:
4pcs Terminal crimp connectors
4pcs Adhesive foams for wrapping
2pcs Woofer adaptor cable bar ends (marked with WF)
1pc Pry tool
1pc Manual
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure the
negative terminal from your battery/power source. This will prevent the risk of
damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from
any possible connection belonging to the battery/power source system.
Mounting info
Some sound systems may vary in size of the door speaker. Make sure that your vehicle has the same
speaker size as this speaker, before you start the assembly
Bolts size can vary between 7 & 8 mm
Torx size can vary between T20 & T25
2

Remove the trim panel by using a PRY tool:
General door panel dismounting
3
This is a generic mounting instruction. The approach is similar to all of the described car models. Some screws and
clips may be placed differently and depending on your car model (see specific car models on the following page).
1
2
Remove the bolts using 7mm hex bit:
3
4
Remove the window control panel using PRY tool.
Unplug the harness:
5
T20/T25 screw is located under the panel.
Remove screw.
6
T20/T25 screw can be seen from under the arm
rest, or there’s a cover that needs to be removed.
Finally. Move the door panel upwards to dismount.
8
7

Dismount the door by removing the cover of the
door panel.
Hint: Use plastic PRY tools to avoid marks on
the panels or damaging the plastic clips.
Dismount door panel
Installation
1
2
3
4
1
1
2
3
4
XC90
1) Remove the cover behind the door handle. Use
PRY tool. Behind the cover are two T20/T25 screw.
Unscrew them. Move the door panel upwards.
Hint: Sometimes it’s easier to remove the window
control panel and unplug the harness, before lifting
up the door panel.
S90/V90
Remove the trim panel by using a PRY tool.
Start at 1) and move towards 2).
Behind the trim panel are two 7mm bolts located.
Remove screw.
3) Remove the window control panel using PRY
tool. Unplug the harness. T20/T25 screw is located
under the panel. Remove screw.
4) T20/T25 screw can be seen from under the arm
rest, or there can be a cover that needs to be
removed.
Move the door panel upwards.
S90/V90
S60/V60
1) Remove the window control panel with PRY
tool.Behind the control panel is one T25 screw
located. Unscrew it. Unplug the harness.
Start by removing the cover by the speakers. Use a
PRY tool.
2) Start in the inside of the cover. Work your way
towards the door handle.
3) Push the trim in the direction of the arrow. (There
is a hook behind the trim)
Behind the trim is a 7mm bolt. Unscrew the bolt.
Unplug the harness.
4) Under the arm rest is one T25 screw. Unscrew it.
Move the door panel upwards.
Remember: Use the PRY tools to avoid
marks on the panels or damaging the
plastic clips.
4

XC60
1) Remove the window control panel with PRY tool.
Behind the control panel is one T20/T25 screw
located. Unscrew it. Unplug the harness.
2) Under the arm rest is one T20/T25 screw.
Remove the cover. Unscrew it.
3) At the bottom of the panel is a 7 or 8mm bolt.
Unscrew it.
Move the door panel upwards.
12
3
XC40
1) At the bottom of the panel are two 7 or 8mm
bolts. Unscrew them.
2) Under the arm rest are two T20/T25 screw.
Unscrew them.
3) Behind the door handle is a rubber cover.
Remove cover and under it is a 7 or 8mm bolt.
Unscrew the bolt.
Move the door panel upwards.
Hint: Sometimes it’s easier to remove the window
control panel and unplug the harness, before lifting
up the door panel.
1
2
3
5
There are several electric and mechanical
connectors on the backside of the door panel.
Disconnect the cables to the door handle, speaker,
window control and door light.

Change speakers
HINT: DLS recommends adding sound deadning
material on the door panel before the assembling.
6
Remove the woofer by unscrewing the T20 Torx.
Unplug the speaker harnesses.
Make sure to use adhesive foam pads to wrap the
adaptor cables to avoid rattle from the door panel.
Plug in the new adaptor cable.
The adaptor cable - WF, shall be used if original
connector is cut.
Use the OEM screws to fix the new DLS woofer.
Make sure that the new DLS woofer is properly
fixed and don’t touch the surrounding plastic.

7
Reassembly door
4
3
2
1
32
1
3
2
1
4
3
2
1
Connect all plugs to the door cover, reconnect the unlocking device, place the door cover from the top, by the
window seal and push it gently down. Make sure the clips are in place and can engage. Give the door panel
a push by the hand to attach to the clips. Mount and fasten all screws to the correct places. Make sure that no
screws or clips are left over.
Reconnect the battery/power source terminal.
Now it’s time to play some good music and enjoy!

8
Running-in time
Allow the speaker to play for at least 15-20 hours in order to perform at its possibly best.
This run-in can be made with tone sweep or with just music.
Start at a moderate volume and increase the volume step by step during the running in
period. After the 15-20 hour run in session the performance and characteristics will be in
the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your
country. You can always contact the DLS Help desk in Sweden at e-mail: [email protected]. Information can also
be found on our WEB- site www.dls.se. We follow a policy of continuous advancement in development. For
this reason, all or part of the specifications and designs may be changed without prior notice.

Specifications
Art. no CD-CRPP-VO2.64
Woofer 6.5” / 165mm with glass fibre cone
RMS Power 100W
MAX Power 200W
Impedance 4 Ohm
Sensitivity 86dB 1W/1M
Freq. range 55 - 5000Hz
Technical specifications
Voice Coil Material CCAW voice coil/ Kapton former
Basket Glass Fibre Reinforced ABS
Magnet Ferrite
Cone Glass fibre
Suspension Rubber
Electro-Acoustic Parameters
Re 3.2 Ohm
Fs 60.4Hz
Mms 14.1gr
Cms 0.492
Vas 13.48L
Qts 0.87
Qes 1.15
Qms 3.71
Bl 3.86T.m
Spl 86dB 1W/1M
Sd 139cm²
Art. no CD-CRPP-VO2.68
Woofer 6.5” / 165mm with glass fibre cone
RMS Power 100W
MAX Power 200W
Impedance 8 Ohm
Sensitivity 87.7dB 1W/1M
Freq. range 55 - 5000Hz
Technical specifications
Voice Coil Material CCAW voice coil/ Kapton former
Basket Glass Fibre Reinforced ABS
Magnet Ferrite
Cone Glass fibre
Suspension Rubber
Electro-Acoustic Parameters
Re 7.2 Ohm
Fs 59.1Hz
Mms 15.4gr
Cms 0.471
Vas 12.91L
Qts 0.62
Qes 0.69
Qms 6.132
Bl 7.71T.m
Spl 87.7dB 1W/1M
Sd 139cm²
9
Impedance VS Frequency
CRPP-VO2.64
CRPP-VO2.68

Dimensions
10
77mm
90mm
34mm
69.5mm
176mm
Ø176mm
4-Ø7mm
94mm
Ø151mm
163mm

The DLS Cruise CRPP-VO2.64 & CRPP VO2.68 woofer speakers are developed to be installed in the
front door of Volvo car models.
DLS Cruise CRPP-VO2.64 compatible car models
Car Model Year Front speaker Rear speaker
Volvo S60/V60 2018-Present CRPP-VO2.64*
Volvo S90/V90 2016-Present CRPP-VO2.64*
Volvo XC40 2017-Present CRPP-VO2.64*
Volvo XC60 2017-Present CRPP-VO2.64*
Volvo XC90 2014-Present CRPP-VO2.64*
*Disclaimer
Only compatible with Harman/Kardon and B&W sound system.
Compatible car models
DLS Cruise CRPP-VO2.68 compatible car models
Car Model Year Front speaker Rear speaker
Volvo S60/V60 2018-Present CRPP-VO2.68**
Volvo S90/V90 2016-Present CRPP-VO2.68**
Volvo XC40 2017-Present CRPP-VO2.68**
Volvo XC60 2017-Present CRPP-VO2.68**
Volvo XC90 2014-Present CRPP-VO2.68**
**Disclaimer
Only compatible with Performance and High Performance sound system.
11

This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS
Directive for the European Union. In common with all Electrical
and Electronic Equipment (EEE) the product should not be
disposed of as household waste. Alternative arrangements may
apply in other jurisdictions.
aideMeliboMnaeporuEehtforentraplabolgasiSLD
Association, an organisation that focus on promoting the
custom made mobile media installations to consumers.
Product markings
We follow a policy of continuous advancement in development. For this reason all or part of
specifications & designs may be changed without prior notice. We reserve for possible typos,
factual or numeric errors that may have been printed on any products, package designs,
user manuals and/or other included accessories.
The crossed-out wheelie bin symbol means that the product, literature and
packaging included must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.
12

DLS Sweden l [email protected] l www.dls.se