DMI Sports FT250DS User manual

DMI Sports For Customer Service Call 1.800.399.4402
1.800.399.4402
FAX: [phone]
Please have your model number when inquiring about parts.
Or write to:
DMI Sports
Customer Service
375 Commerce Drive
Fort Washington PA, 19034
Please visit our web site at:
www.dmisports.com
When contacting DMI Sports, please provide your model number
and item number (if applicable) if requesting a replacement part.
Item numbers can be found inside this owners manual.
Congratulations on the purchase of your new DMI Sports
Soccer table. Our products are designed and
manufactured to give you years of game playing enjoyment.
KEEP BOX AND PACKING MATERIAL UNTIL TABLE
HAS BEEN COMPLETELY ASSEMBLED.
ALL DAMAGE MUST BE REPORTED TO DMI
WITHIN TEN DAYS OF RECEIPT.
If you have any problems with your new product,
PLEASE DO NOT RETURN IT TO THE STORE.
Please contact us:
Your Model Number _______________________
Your model number is also located on the original carton. These instructions
are also available online at: www.dmisports.com.
FT250DS
0100605

DMI Sports For Customer Service Call 1.800.399.4402
Please Keep Your Instructions! (You will need your Model number should you need to contact us.)
Before attempting assembly, please read through this instruction book to familiarize yourself with all
the parts and assembly steps. We recommend that two adults assemble this table. Please refer to the
Parts Identifi er on the following page and be sure that all parts have been included. Although extreme-
ly rare, occasionally a part may be missing. If you are missing a part, or if you have any questions, please
call our customer service department at 1.800.399.4402 Mon-Fri between the hours of 9:00am and
5:00pm E.S.T; or you can reach us at: www.dmisports.com.
Do not return the game to the store. Please contact us fi rst at: 1.800.399.4402 or on our website at:
www.dmisports.com.
IMPORTANT!
TWO ADULTS ARE REQUIRED TO ASSEMBLE
THIS SOCCER TABLE
-2-

DMI Sports For Customer Service Call 1.800.399.4402
PARTS IDENTIFIER
HARDWARE PARTS
A1 A2
Sand Blasted Ball
RPFT-BALL
Qty. 2 Qty. 1
ACCESSORY PARTS
-3-
H1 H2 H3 H4
Qty. 3 Qty. 24 Qty. 6 Qty. 4
TOOLS REQUIRED FOR ASSEMBLY:
• Phillps Head Screw driver- Not Included
• Level recommended- Not Included
• Allen Wrench - Included
H5 H6 H7 H8
Qty. 24 Qty. 22 Qty. 8
H9 Qty. 26
Qty. 26
Support Rod
RPFT250DS-SROD
Washer, 5/16” Black
RPFT-5/16WASH
Nut, 1/4” x 1/2”
RPFT250DS-NUT
Screw, 1 3/4”
RPFT250DS-1-3/4
Screw, M4 x 1/2”
RPFT-M4SCREW
Screw, 1”
RPFT-1”SCREW
Bolt, 5/16” x 1 3/4”
RPFT250DS-BOLT
5/32” Locking Nut
RPFT-5/32NUT
Bolt, 5/32” x 1-1/8”
RPFT-5/32BOLT
5mm Allen Wremch
RPFT-5MMTOOL
H10 Qty. 8
Screw, 3/4”
RPFT-3/4SCREW
Note: H6 Screws will be used to secure the Goal system, Ball entry and the Cup Holders.
Cup holders should be applied when the table is completely assembled. Your table should
appear, as it does in the image on page 2 of this instruction manual, when assembled.

DMI Sports For Customer Service Call 1.800.399.4402
-4-
P8 Qty. 2
ASSEMBLY PARTS
P1 P2 P3 P4
P5 P6 P7
Side Panel
RPFT250DS-SPANL
Qty. 2 Qty. 2 Qty. 1 Qty. 4
Qty. 3 Qty. 8 Qty. 8
P16 Qty. 16
P9 P10 P11 P12
P13 P14 P15
Qty. 2 Qty. 2 Qty. 2 Qty. 2
Qty. 2 Qty. 4 Qty. 2
P17 P18 P19 P20
P21
Qty. 16 Qty. 13 Qty. 13 Qty. 16
Qty. 2
End Panel
RPFT250DS-EPANL
Rod Bushing
RPFT250DS-BUSH
Leg
RPFT250DS-LEG
Support Brace
RPFT250DS-BRACE
Play Field
RPFT250DS-FIELD
Ball Catcher
RPFT250DS-CATCH
Goal
RPFT250DS-GOAL
Ball Entry Cup
RPFT250DS-ENTRY
Handle
RPFT250DS-HANDL
Rubber Rod Bumper
RPFT-BUMPER
Plastic Washer
RPFT-PLWASHER
Rod Cap
RPFT-RODCAP
Ball Runner
RPFT250DS-RUN
Slide Scorer
RPFT250DS-SCORE
5 Player Rod
RPFT250DS-5ROD
3 Player Rod
RPFT250DS-3ROD
2 Player Rod
RPFT250DS-2ROD
Away Men
RPFT250DS-AWAY
Home Men
RPFT250DS-HOME
Leg Levelers
RPFT250DS-LEV
PARTS IDENTIFIER
P22 Qty. 4
Cup Holder
RPFT250DS-CUP
P23 Qty. 2
Support Beam
RPFT250DS-BEAM

DMI Sports For Customer Service Call 1.800.399.4402-5-
STEP 1.
Insert the rods through the sides of the play-
ers as shown here in Figure 1a. Apply Washers
(P17) between Bushings (P16) and the men as
shown here.
(Note: Figure 1a. shows Rod (P14) with three
home players being applied using Bolt (H8)
and Locking Nut (H9). Head of Bolt (H8)
should be facing defending goal.)
H9
Figure 1a.
Notice the small lump on
the “front” of the mans base.
This lump should face the
opposing goal.
H8
P17
P17
P16
IMPORTANT!
REMEMBER:
You are working up-side-down. All of the home team must face one direction and the away team must
face the other direction. All home team handles will go on one side, anll the away team handles will go
on the other side. The handle ends are the ends of the rods with holes appoximately 1/2” from the end of
the rod.

DMI Sports For Customer Service Call 1.800.399.4402
-6-
ASSEMBLY
3. Align the rods as shown in FIGURE 1. Choose one team to be color # 1 and one team to be color # 2. The handle end of
the rod has a hole close to the end of the rod. There will be four handles (one team) on each side of the table. Remember,
the goalie rod is always in your left hand when the table is in the upright position and you are working upside down so it will
be opposite during assembly.
4. Once you are sure you have the players set
up correctly, slide the other side panel P1 on
the other end of the rods as shown.
5. Set the playfield P3 onto the assembly with
the graphics facing down. Insert the playfield
into the groves on the side panels.
6. Place the playfield support braces P5 on the
bottom of the playfield as shown in FIGURE 2.
Slide the playfield support rods H1 through
the side panel and the grove in the support
braces. Secure with finishing nut H3.
DO NOT TIGHTEN AT THIS TIME!
7. Attach the two end panels P2 as shown in
FIGURE 3 using bolts H5 and washers H2.
Remember to start all bolts by hand first
before you tighten anything.
8. Center the playfield and secure to the end
panels using screws H7.
Figure 1
Figure 2
Figure 3
1. Find a clean, level place to begin the assembly of your
game table. We recommend building the table on the
box top to protect the parts during assembly.
2. Place one side panel P1 up-side-down with the finished
side facing out as shown in Figure 1. The ball entry hole
will be closest to the floor. To ease assembly, push the
rubber bushings on the rods up against the men.
Insert the rods through the rod bushing in one side as
shown here in Figure 1.
MAKING SURE END PANELS ARE STRAIGHT
TIGHTEN ALL HARDWARE AT THIS TIME.
DO NOT OVER TIGHTEN.

DMI Sports For Customer Service Call 1.800.399.4402
-7-
ASSEMBLY
9. Attach legs as shown in FIGURE 4 using
bolts H5 and washers H2.
Remember to startall bolts by hand before
you tighten the legs.
10. Attach the Goal P10 to the end panels with
screws H6
H5
. Center the box over the opening
in the end panel P2 as shown in FIGURE 4.
TIGHTEN ALL LEG HARDWARE AT
THIS TIME. DO NOT OVER TIGHTEN.
12. Attach the ball entry cups P8 to the side
panels with screws H6 as shown in FIGURE 5.
13. Slide the Handles P6 onto the end of the rod
with the hole close to the end.
Slide the rubber end caps
P7
on the other
ends of the rods.
14. Attach the Slide scorers
15. Leg leveler bolts are 1-1/4” long, which allows
the table to safely be raised or lowered 1/2”.
With levelers screwed in completely, make one
full revolution to each leg leveler, then make
final leveling adjustments from there.
16. (Optional) With a level resting on the play surface,
and parallel to bars, check both ends of the table
play surface and make adjustments to leg levelers
as needed. Repeat process with leveler in
perpendicular direction to bars.
P12 to the top of the
end panels with screws H4 as shown in
FIGURE 5.
11. Attach Ball runner P11 ends to goals and ball
catchers.
12. Screw one leg leveler P22 into the bottom of each
leg.
Figure 5
Figure 4
-7- For Customer Service Call 1-800-399-4402
DMI Sports
THIS STEP REQUIRES TWO OR MORE ADULTS.
Very carefully turn the table over and set it on its legs.
Be careful, the table is very heavy and the rods will slide.
Do not lift the table by holding onto the rods.
9
Secure each Handle P6 using Screws H10.
P10
P23
Attach Support
Beam P23 to legs before tightening leg bolts.

DMI Sports For Customer Service Call 1.800.399.4402
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
A1
A2
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
RPFT250DS-SROD
RPFT-5/16WASH
RPFT250DS-NUT
RPFT250DS-1-3/4
RPFT250DS-BOLT
RPFT-M4SCREW
RPFT-1”SCREW
RPFT-5/32BOLT
RPFT-5/32NUT
RPFT-3/4SCREW
RPFT-BALL
RPFT-5MMTOOL
RPFT250DS-SPANL
RPFT250DS-EPANL
RPFT250DS-FIELD
RPFT250DS-LEG
RPFT250DS-BRACE
RPFT250DS-HANDL
RPFT-RODCAP
RPFT250DS-ENTRY
RPFT250DS-CATCH
RPFT250DS-GOAL
RPFT250DS-RUN
RPFT250DS-SCORE
RPFT250DS-5ROD
RPFT250DS-3ROD
RPFT250DS-2ROD
RPFT-BUMPER
RPFT-PLWASHER
RPFT250DS-AWAY
RPFT250DS-HOME
RPFT250DS-BUSH
RPFT250DS-CUP
RPFT250DS-LEV
RPFT250DS-BEAM
Support Rod
5/16” Black Washer
Nut, 1/4” x 1/2”
1 3/4” Screw
Bolt, 5/16” x 1-3/4”
Screw, M4 x 1/2”
1” Screw
Bolt, 5/32” x 1-1/8”
5/32” Locking Nut
3/4” Screw
Sand Blasted Ball
5mm Allen Wrench
Side Panel
End Panel
Playing Field
Leg
Support Brace
Handle
Rod Cap
Ball Entry Cup
Ball Cather
Goal
Ball Runner
Slide Scorer
5 Player Rod
3 Player Rod
2 Player Rod
Rubber Rod Bumper
Plastic Washer
Away Player
Home Player
Rod Bushing
Cup Holder
Leg Levelers
Metal Support Beam
UNIT
PRICE
TOTAL
AMOUNT
Subtotal:
PA Residents Add 6% State Sales Tax:
Shipping and Handling Charges:
TOTAL:
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
(ea.)
PARTS RE-ORDER FORM FT250DS Soccer Table
DATE:
NAME:
ADDRESS:
CITY:
PHONE:
STATE: ZIP CODE:
Send this form along with your
check or money order payable to:
DMI SPORTS
375 Commerce Drive
Fort Washington, PA 19034
www.dmisports.com
15.00
.25
.75
.25
.50
.25
.25
.25
.25
.25
2.50
1.00
40.00
30.00
25.00
10.00
5.00
1.00
.50
3.00
9.00
9.00
4.00
7.00
16.00
16.00
16.00
.50
.50
.50
.50
2.00
5.00
5.00
9.00
SHIPPING AND HANDLING:
Up to $15.00 add $2.00 for S&H
Over $15.00 add $8.00 for S&H
Console add $5.00 for S&H
REF PART # DESCIPTIONQTY