Dmp electronics X1 Installation guide

LT-2264 1.01 21011

X1 DOOR CONTROLLER

INSTALLATION AND PROGRAMMING GUIDE

TABLE OF CONTENTS

X1 Door Controller Overview��1

Door Controller Power��1

Door Controller PCB Components��1

Door Controller Plug-In Terminals��1

Mount the System�� 2

Connect a Card Reader �� 2

Connect a Wiegand Card Reader��2

Connect an OSDP Card Reader��2

Optional Second Card Reader��2

Wire the Inputs �� 3

Door Switch (DS) ��3

Request to Exit (RX)��3

Custom Input (CI) ��3

Ground (G)��3

Wire the Outputs�� 3

Aux Output 1 & 2 (O1 & O2)��3

12V+ (12V) ��3

Wire the Electronic Lock�� 4

Form C Relay �� 4

Diode�� 4

Wet/Dry Jumper �� 4

Determine Communication �� 5

X-PoE Connection (Optional) ��5

Ethernet Connection ��5

Cellular Backup (Optional)�� 6

Wi-Fi Connection �� 6

Apply Power�� 7

Wire the Input Power ��7

Wire the Battery��7

Wiring Example ��7

Connection Settings �� 8

Conﬁgure Wi-Fi Settings�� 8

Conﬁgure Network Settings �� 8

Conﬁgure Cell Settings�� 8

Program in Dealer Admin�� 9

Sign In to Dealer Admin �� 9

Add a Customer�� 9

Add a System �� 9

Add an X1 ��10

Add Card Formats��10

Enable Video Services�� 11

Add an App User�� 11

Log In as a Customer�� 11

Test the System��12

Additional Information ��12

LEDs �� 12

Cell Module Removal �� 12

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 1

X1 DOOR CONTROLLER OVERVIEW

The X1 Series is a cloud-based access control system that is fully programmed in Dealer Admin™ and

maintained in Virtual Keypad™� This guide will cover mounting the system, wiring devices to the system,

configuring network options, applying power, programming the system in Dealer Admin, and testing the

system�

Door Controller Power

Powered by: Maximum Current Draw:

Power Terminals 1�5 A

PoE 750 mA

Door Controller PCB Components

Refer to the diagram below throughout the installation�

+AC/DC- +BAT- R1 W1 G1 B1 LC BC R2 W2 G2 B2 LC BC DS RX CI G 01 02 12V NC C NO

Power

Battery

In Reader

Out Reader

Inputs

Auxiliary Outputs

Door Relay

Wet/Dry Jumper

PWR/BOOT

READER 1

READER 2

RELAY

DATA

FIRE

LOCKDOWN

Operation LEDs

Ethernet Port

PoE Module Headers

Cell Module Header

A

B

D

E

F

G

H

I

J

K

L

M

AEF

GHIJKLMN

R and L Terminal

C

N

R

L

BD

Wi-Fi LED

Door Controller Plug-In Terminals

Wiring terminals on an X1 Series system is done easily by using the plug-in

terminals�

1� Insert the wire into the slot�

2� Tighten the screw on the bottom�

3� Snap the plug-in terminal onto the Door Controller board�

Plug In

1

2

3

Insert

Tighten

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 2

CONNECT A CARD READER

The X1 Series provides connections for 2 readers� The first reader is designated for the In Reader and the

second is designated for the Out Reader�

The X1 Series system also provides direct 12 VDC output to the reader on the RED terminal connection�

Terminal Name Wiegand Function OSDP Function

R1 & R2 12V+ DC +

W1 & W2 Data 1 B (485 +)

G1 & G2 Data 0 A (485 -)

B1 & B2 12V- (ground) DC -

LC LED Control N/A

BC Wiegand Buzzer Control N/A

Connect a Wiegand Card Reader

1� Connect the red wire (12 VDC) to terminal R1�

2� Connect the white wire (Data One) to W1�

3� Connect the green wire (Data Zero) to G1, black (ground) to B1�

4� Connect the orange or brown wire to LC�

Connect an OSDP Card Reader

1� For data transmission, connect the A wire (485 –) to the G1

terminal and the B wire (485 +) to the W1 terminal�

2� For reader power, connect the red wire (DC + ) to the R1 terminal and the black wire (DC –) to the B1

terminal�

Note: The wire colors may be different depending on the reader being installed� Refer to the literature

provided with the reader for wire coding, wire distance, cable type (such as shielded), and other

specifications� The figure above shows the DMP-preferred wiring�

Optional Second Card Reader

For an out reader, connect the red, white, green, and black wires to the Reader 2 terminals: R2, W2, G2, and

B2� Connect the orange/brown wire to LC�

If using only one reader, it must be connected to reader 1�

MOUNT THE SYSTEM

The metal enclosure for the X1 Series must be mounted directly to a wall, backboard, or other flat surface in

a secure, dry place to protect the system from damage� Do not remove the PCB from the enclosure�

Red

White

Green

Black

Orange/Brown

(Wiegand LED)

Card Reader

Reader 1 Terminals

R1 W1 G1 B1 LC BC

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 3

WIRE THE INPUTS

Door Switch (DS)

Connect a door contact or door position switch to indicate the status

of the door, whether it is open or closed� Use this terminal if enabling

door prop or door force�

This terminal is a Normally Closed input�

Request to Exit (RX)

Connect a motion sensing device or a mechanical switch to provide

RX capability to the system� RX can be used to activate the door

relay� When activated the RX activates the door lock relay based on

the programmed unlock time� Use this terminal if enabling forced

door�

This terminal is a Normally Open input�

Custom Input (CI)

This input triggers a rule programmed in Dealer Admin� This could

be a button on a front desk for a receptionist to release a front door�

This could also be used as a fire alarm input�

This terminal is a Normally Open input�

Ground (G)

This terminal is the ground for the inputs�

+AC/DC- +BAT- R1 W1 G1 B1 LC BC R2 W2 G2 B2 LC BC DS RX CI G01 02 12V NC C NO

DS RX CI G

WIRE THE OUTPUTS

Use these switches to ground outputs for local outputs or door

alarms such as sounders, lights, or sirens� These are 12 VDC outputs�

For example, a sounder could be wired for local indication of a door

prop or door force event�

Aux Output 1 & 2 (O1 & O2)

Attach the negative wire of the device here�

The outputs must be less than 98�5 ft (30 m) long�

12V+ (12V)

Attach the positive wire of the device here� +AC/DC- +BAT- R1 W1 G1 B1 LC BC R2 W2 G2 B2 LC BC DS RX CI G 01 02 12V NC C NO

01 02 12V

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 4

WIRE THE ELECTRONIC LOCK

Form C Relay

The X1 Series system provides a Form C (SPDT) relay for controlling locks and other electronically-controlled

barriers� The three relay terminals marked NO C NC allow you to connect the device wiring to the relay for

module control�

The Form C relay draws up to 35 mA of current and contacts are rated for 1 Amp (resistive) at 12 VDC� When

connecting multiple locks to the Form C relay, the total current for all locks cannot exceed 1 Amp� If the total

current for all locks exceeds 1 Amp, problems will arise, it will not work as intended, and an isolation relay will

be required�

Diode

Connect the included diode as close to the magnetic lock or door strike as

possible to prevent inductive kickback� Observe polarity when connecting the

diode�

Wet/Dry Jumper

Putting the jumper on the top two terminals will place it in the dry condition and putting the jumper on the

bottom two terminals will place it in the wet condition� When using a dry relay, a power supply is needed to

power the lock/strike� When using a wet relay power is already supplied through the relay�

Power Supply

Magnetic Lock positive

to Terminal NC

Power Supply positive

to Terminal C

Magnetic Lock negative to

Power Supply negative

NO

C

NC

Magnetic Lock - Normally Closed and Dry

DRY WET

Jumper set

to Dry

–+

Magnetic Lock

Diode

Magnetic Lock - Normally Closed and Wet

Magnetic Lock positive

to Terminal NC

Magnetic Lock negative to

X1 terminal B2

NO

C

NC

DRY WET

Jumper set

to Wet

Reader 2

–+

Magnetic Lock

B2

R2 W2 G2 LC BC

Diode

NO

C

NC

Door Strike - Normally Open and Dry

DRY WET

Jumper set

to Dry

Door Strike positive

to Terminal NO

Power Supply positive

to Terminal C

Door Strike negative to

Power Supply negative

–+

DC Door Strike

Power Supply

Diode

Door Strike - Normally Open and Wet

Door Strike positive

to Terminal NO

Door Strike negative to

X1 terminal B2

DRY WET

Jumper set

to Wet

Reader 2

–+

DC Door Strike

NO

C

NC

B2

R2 W2 G2 LC BC

Diode

+-

Positive Negative

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 5

PoE Module

X1 PoE Module Headers

PoE Module

Gently press the PoE Module

onto the PoE Module Headers.

Verify that the PoE is in the position

shown here.

12

DETERMINE COMMUNICATION

The options in this section are in the DMP-recommended installation order� If an option is not part of your

desired application, move to the next option�

X-PoE Connection (Optional)

For a PoE connection, gently push the PoE Module onto the X1 PoE Module headers�

Warning: Make sure that the Ethernet cable is unplugged before connecting the PoE module�

Ethernet Port

Ethernet Connection

Connect an Ethernet cable from the LAN/WAN connection to

the X1 PCB Ethernet port�

Two LEDs are located on the Ethernet port�

• The green LED indicates data is being sent over the

network�

• The yellow LED indicates the speed of the transmission�

A solid yellow LED indicates the network is connected

at 100BASE-T� A flashing yellow LED indicates the

network is connected at 10BASE-T�

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 6

Wi-Fi Connection

A Wi-Fi connection or a static IP address must be established after

power up� See Wi-Fi instructions later in this guide�

Note: You can connect via an Ethernet or a Wi-Fi connection,

but not both at the same time�

Wi‑Fi Antenna

The yellow Wi-Fi antenna connects to the right of the cell antenna on

the enclosure�

1� If the cable has become detached from the X1, simply wire

it back onto the Wi-Fi module and run the cable around the

module�

2� Run the Wi-Fi cable to the top of the enclosure as shown here�

X1 Enclosure

Wi-Fi Antenna

Cellular Connection (Optional)

If the network cable or Wi-Fi are not connected, cell will be the primary communication� If the network

cable or Wi-Fi are connected, the cell will be the backup communication�

1� Attach the included standoff to the Door Controller�

2� Carefully insert the antenna connector of the Cell Module through the top of the enclosure�

3� Plug the Cell Module onto the standoff�

4� Plug the Cell Module into the Cell Header�

5� Attach the Cell Module Antenna to the antenna connector with the washers on the inside and the top

of the enclosure�

Cell Module

Header

Stando

Cell Module

Stando

Header

Cell Antenna

Cell Module

Enclosure

Door

Controller

12345

Door Controller

Enclosure

Antenna Connector Door Controller Door Controller

Nut and Washer

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 7

+AC/DC- +BAT- R1 W1 G1 B1 LC BC R2 W2 G2 B2 LC BC DS RX CI G01 02 12V NC C NO

DRY WET

Red

12 V Battery

-

+

Orange/Brown

(Wiegand LED)

Card Reader

Red

White

Green Black

Optional

Second

Card Reader

Transformer

-

+

Power Indicator

Door

Contact

G

DS

Request

to Exit

G

RX

Custom

Input

G

CI

AUX

Output 1

12V

O1

12V

O2

AUX

Output 2

–+

Magnetic Lock

Jumper Set to Wet

NC

B2

XX = wire polarity or terminal location

APPLY POWER

Warning: Refer to your local state regulations before connecting to building power� Wiring methods

shall be in accordance with NEC, NFPA72, ANSI, and with all Authority Having Jurisdiction

Wire the Input Power

Connect the transformer wires or external power to terminals 1 and 2 on the X1

PCB� Use no more than 70 ft� of 16 gauge or 40 ft� of 18 gauge wire between the

transformer and the X1 PCB�

Wire the Battery

Connect the red battery lead to the battery positive terminal� Connect the black

battery lead to the negative battery terminal� Observe polarity when connecting the

battery�

Wiring Example

The diagram here shows the transformer and the battery wiring� It also shows

a possible application with an electronic lock wired normally closed with wet

contacts�

Battery Harness

Red

12 V Battery

-

+

+AC/DC- +BAT-

+-

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 8

CONNECTION SETTINGS

If not connecting over Ethernet, connect to Wi-Fi at this time� If connecting over Ethernet, skip to Configure

Network Settings�

Conﬁgure Wi-Fi Settings

On power up, the X1 broadcasts an SSID of DMPX1 followed by the system’s serial number� No password is

required to connect to the SSID�

The Wi-Fi LED blinks during the broadcast�

1� Connect to the X1 SSID using a device capable of launching a browser (cell phone, laptop, etc�)�

Note: If using a phone, use only Wi-Fi and disable mobile data� Some phones will try to use the

mobile data connection if the Wi-Fi does not have an internet connection�

2� Enter 192�168�1�1 into the URL field� The Wi-Fi LED will blink�

3� In the Wi-Fi options, enter the customer's Wi-Fi network information�

4� Select Apply, and the X1 will reset�

Once the X1 has reset it will automatically connect to the customer's

network with the updated settings�

Note: If fifteen minutes have passed since power up or the X1 does

not broadcast an SSID, short the L terminals for 3 seconds and then

place the jumper back on one pin of the L terminal� This will give an

additional fifteen minutes of broadcasting�

Conﬁgure Network Settings

1� Connect to the X1 SSID using a device capable of launching a

browser (cell phone, laptop, etc�)�

Note: If using a phone, use only Wi-Fi and disable mobile

data� Some phones will try to use the mobile data connection

if the Wi-Fi does not have an internet connection�

2� Enter 192�168�1�1 into the URL field�

3� In the DHCP options, make edits to the desired fields�

• DHCP: This option is toggled on as default�

• Static IP: Toggle o DHCP and enter the information in the required ﬁelds�

4� Select Apply, and the X1 will reset�

Conﬁgure Cell Settings

On power up, if using cell, the X1 automatically connects and programming in Dealer Admin can begin�

L

R

L

R

Wi-Fi LED

L Terminal

3

4

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 9

PROGRAM IN DEALER ADMIN

After you’ve installed the X1 Series Door Controller and configured basic communication settings, follow the

steps in each of the following sections to program a system in Dealer Admin:

1� Sign In to Dealer Admin

2� Add a Customer

3� Add a System

4� Add the X1

5� Add Card Formats

6� Enable Video Services

7� Add an App User

8� Log in as Customer

Sign In to Dealer Admin

Go to the Dealer Admin login page� Enter your Email and Password, then press Sign In�

Add a Customer

1� At Customers, press the Add icon �

2� Enter the customer’s name and email�

3� Enter the customer’s contact information if desired�

4� Press Save�

Add a System

Before you can add a door controller or program doors, you must add a system in Dealer Admin�

1� Go to Customers�

2� Select a customer to open the Customer Summary�

3� In Systems, press the Add icon �

4� Enter a name for the system�

5� In System Type, select X1�

6� Configure billing address and time options as needed�

7� Enter the door controller’s serial number�

8� Press Save�

1

2

3

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 10

Add an X1

If door options don’t open automatically, select the X1 that you want to configure�

1� Enter a descriptive name for the door�

2� In Strike Time, enter the number of seconds that you want the door to unlock when access is

granted�

3� In Strike Delay, enter the number of minutes that you want to delay the door unlock when

access is granted�

4� In Reader Protocol, choose a protocol for this door’s readers: Wiegand or OSDP� For OSDP

readers, configure buzzer and LED options�

Note: OSDP readers must be either new or factory reset so they can bind properly with

the system� A unique OSDP secure key is automatically programmed�

5� In Authorization, choose which authorization type can be used to access any of the doors�

Additional Door Options:

• Buzzer (OSDP) allows the reader to beep when a card is read�

• LED (OSDP) allows the reader LED to turn on and operate the same as a Wiegand reader LED, lighting green when

the module relay activates� If disabled, the reader LED is turned o and does not operate in any condition�

• Card (Authorization) enables the use of cards for any of the doors�

• Card + PIN (Authorization) enables the use of cards or card + PIN for any of the doors�

• Dual Authority (Authorization) enables the use of cards or dual authority for any of the doors�

• Fire Zone indicates this custom output triggers with a ﬁre alarm�

• Fire Exit allows the door to unlock during a ﬁre so people can exit the area�

• Include in Lockdown allows this door to be included when a lockdown is initiated�

• Door Sensor allows a motion detector mounted near the door to trigger a request to exit�

• In Prop Time, enter the number of seconds that you want to allow the door to remain open without triggering an

alert�

• Door Forced Message sends a status message any time a door is forced open�

• Request to Exit (REX) requires people to request exit� REX is usually triggered by motion near the door or a button

press�

6� Turn on additional options as needed�

7� Press Save�

Add Card Formats

The first card format for any door is defaulted to DMP� Refer to Card Format Options below when

programming card formats�

1� In Card Formats, press the Add icon �

2� Give the card format a name�

3� Select a card format and configure format settings�

Card Format Options�

• DMP (card format) use cards with DMP’s format with a 26 – 45 bit data string�

• Custom (card format) use cards with a custom bit length and conﬁguration�

• Any (card format) unlock the door with any valid card read�

• Wiegand Length is the total number of bits to be received in Wiegand code including parity bits�

• Site Code Position is the site code start position in the data string�

• Site Code Length is the site code length�

• User Code Position deﬁnes the user code start bit position�

• User Code Length deﬁnes the credential user code length�

• User Code Digits deﬁnes the user code length�

• Require Site Code restricts the door so it only unlocks when the card’s site code matches one programmed in Site Code�

4� Press Save�

5

4

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 11

Enable Video Services

1� In Video Services, press the Add icon �

2� Select the types of cameras or NVRs that you want to enable on the system�

3� Select any third-party applications that you want to enable on the system� This allows users

to sign in to their services from Virtual Keypad�

4� Press Save�

5� Back on the System Information page, select the number of cameras and storage space you

require or choose the number of doorbells that you want to add to the system�

Add an App User

Adding an app user to an X1 system automatically adds them as a user in Virtual Keypad�

1� Go to Customers�

2� Select a customer to open the Customer Summary�

3� In the App Users section, press the Add icon �

4� For a user that doesn’t have a Virtual Keypad account, select New� For a user that already has

an account, select Existing�

5� For a new user, enter their email address� For an existing user, start typing to search for their

email and select it from the list�

6� Set the user’s authority level to either Administrator to manage multiple systems or Standard

to manage a single system�

7� For a new user, enter their first and last name� If you don’t want to generate a random

password for the user, clear Create Random Password then manually enter one�

8� If you want to email the user video clips, select Email Video Clips�

9� Select systems and permissions for the user�

10� Press Save�

Note: If you receive a message that states the email is already in use, the user already has a

Virtual Keypad account� Select Existing below the user’s email address�

Log In as a Customer

To log in to Virtual Keypad and view the system like a customer would, press Login as Customer�

This adds you to the system as a temporary app user with admin privileges without the capability

to view video� Your temporary app user expires and is automatically removed from the system after

1 hour�

7

8

6

X1 INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS 12

TEST THE SYSTEM

Make sure that the Reader LED(s) is on and the Door Controller’s Power LED is on� If connected to Wi-Fi,

the Wi-Fi LED is on solid� If connected to network, the Network Port light is blinking� For cell and all

communication methods, check that Door Controller is communicating with Dealer Admin and Virtual

Keypad after Dealer Admin programming is completed�

ADDITIONAL INFORMATION

LEDs

LED Meaning

PWR/BOOT On when board is powered and operating

READER 1 Turns on for one second to indicate receipt of a valid input from the In Reader determined by card

format programming

READER 2 Turns on for one second to indicate receipt of a valid input from the Our Reader determined by card

format programming

RELAY On when door relay is active

DATA Not used on X1

FIRE On when the Door Controller is in a fire alarm

LOCKDOWN On when the Door Controller is in a lockdown state

Cell Module Removal

1� Unscrew the washer on top of the enclosure and remove the

Cell Module antenna�

2� Unplug the Cell Module from the Cell Header�

3� Pinch the tab of the standoff to release the module from the

Door Controller�

Tab

Designed, engineered,

and manufactured in

Springﬁeld, Missouri

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | dmp.com

X1 DOOR CONTROLLER

Speciﬁcations

Power

Input 12 V - 24 V AC/DC 2A

Battery 1.5 Ah (recommended)

Power Output Max* 1.5 A; PoE 750 mA

O1, O2 Max 50 mA

*Max Power output is a board’s total available power for all attached

equipment

Communication Options

Ethernet

Wi-Fi

Cellular 263LTE-A-X1, 263LTE-V-X1

Mechanical

Enclosure Dimensions 6.5” W x 8” H x 3” D

16.5 cm W x 20.3 cm H x 7.6 cm D

Weight 4 lbs

Environmental

Temperature 0 ° C to 49 ° C

32 ° F to 120 ° F

Humidity 85%

Compatibility

263LTE-A-X1 (X1) Cell Module

263LTE-V-X1 (X1) Cell Module

X1-POE PoE Module

X1PCB PCB Replacement

Certiﬁcations

ANSI/UL 294 Access Control System Units

Level I Destructive Attack and Line Security

Level IV Endurance and Standby Power

Manufacturer’s Limited Warranty

3 Year warranty against defects in materials and

workmanship. Visit DMP.com for full details.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules� Operation is subject to the following two conditions:

1� This device may not cause harmful interference, and

2� this device must accept any interference received, including interference that may cause undesired operation�

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7�874 in�) from all persons� It must not be located

or operated in conjunction with any other antenna or transmitter�

Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment�

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules� These

limits are designed to provide reasonable protection against harmful interference in a residential installation� This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications� However, there is no guarantee that interference will not occur in a particular installation� If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

1� Reorient or relocate the receiving antenna�

2� Increase the separation between the equipment and receiver�

3� Connect the equipment into an outlet on a circuit different from that to which the receiver is connected�

4� Consult the dealer or an experienced radio/TV technician for help�

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence-exempt RSS standards� Operation is subject to the following two conditions:

1� This device may not cause interference, and

2� this device must accept any interference, including interference that may cause undesired operation of the device�

This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6� The system

must be installed at a minimum separation distance from the antenna to a general bystander of 7�87 inches (20 cm) to maintain compliance with the

General Population limits�

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

1� l’appareil ne doit pas produire de brouillage, et

2� l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS‑102 et est jugée conforme aux limites établies par le Code de sécurité 6

de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité

avec les limites permises d’exposition du grand public.

DMP Electronics X1 Installation guide

Popular Controllers manuals by other brands