DMP Electronics 1100DE Series User manual

1100D SERIES WIRELESS RECEIVERS
Installation Guide
Figure 1: 1100D Wireless Receiver
The 1100D Series Wireless Receiver
provides up to 32 wireless zones for
XT30/XT50Series panels. The 1100DE
features 128‑bit AES encryption.
The 1100D Series provides Two‑Way,
supervised communication using
900 MHz frequency hopping spread
spectrum technology. The receiver can
be mounted up to 500feet (152 meters)
from the panel enclosure.
Compatibility
• XT30 Series panels
• XT50 Series panels running
firmware Version 102 or higher
• Encryption requires panel
Version183 or higher
What is Included?
• One 1100D Wireless Receiver
• Hardware Pack
1PROGRAM THE PANEL
Refer to the panel programming guide as needed.
1. Reset the panel.
2. At a keypad, enter 6653 (PROG) to access the
PROGRAMMER menu.
3. In SYSTEM OPTIONS, program a HOUSE CODE
between 1 and 50. See House Code Explained
for more information.
4. If you are programming an XT50 Series panel,
select NO at the BUILT IN 1100 WIRELESS
prompt to allow the panel to use the 1100D for
wireless communication.
5. (1100DE only) At the 1100 ENCRYPTION
prompt, select ALL to only add encrypted
wireless devices to the system. Select BOTH
to allow both encyrpted and non‑encrypted
wireless devices to be programmed.
6. (1100DE only) The default passphrase appears
at the ENTER PASSPHRASE prompt. Press
CMD to keep the default. Press any select key
or area to change the passphrase and enter an
8‑character hexidecimal string (0‑9, A‑F).
7. Press CMD until STOP displays and press
a select key or area to save and exit the
Programmer.
DESCRIPTION
2MOUNT THE 1100D
Select a Location
When selecting a location to mount the 1100D, keep
in mind that the receiver should be centrally located
between the 1100 Series transmitters used in the
installation and no more than 500 feet (152 meters)
away from the panel. Be sure to mount the receiver
away from large metal objects because it may impair
the receiver’s performance. Also, be sure to not use
shielded wire between the panel and receiver. Follow
the directions below to mount the 1100D:
1. Remove the cover from the plastic housing.
2. Use the included #6 screws to secure the 1100D
to the surface. See Figure 2 for mounting hole
locations.
1. Connect the red, yellow, green, and black
wires to the PANEL terminal on the 1100D and
connect the other ends to the 7, 8, 9, and 10
terminals on the panel. See Figure 2.
2. Replace the cover back on to the base. The
panel immediately recognizes the 1100D if the
panel is programmed with a house code.
3WIRE THE 1100D

2 1100D INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
1100D LED Operation
The six labeled LEDs on the 1100D PCB display
wireless receiver operation and activity. See Figure 2
for LED locations and Table 1 for LED indications.
House Code Explained
The house code identifies the panel, receiver, and
transmitters to each other. The 1100D automatically
sends the specified house code to wireless
transmitters when transmitter serial numbers are
programmed into the panel. The 1100D only listens for
transmissions using the specified house code or the
programmed transmitters’ serial numbers.
LED Survey Operation for 1100 Series
Transmitters
1100 Series transmitters provide a survey operation that allows one person to confirm that
each transmitter is communicating with the wireless receiver or panel to easily determine the
best location for the transmitters and the wireless receiver. Follow the directions below to test
communication of the wireless transmitters:
1. Remove the transmitter’s cover.
2. Hold the transmitter in the exact desired location.
3. Press the tamper switch to send data to the wireless receiver and determine if
communication is confirmed or faulty.
Confirmed: If communication is confirmed, the survey LED turns on when data is sent
to the wireless receiver and off when acknowledgment is received.
Faulty: If communication is faulty, the LED remains on for several seconds or flashes
multiple times in quick succession. Relocate the transmitter or the wireless receiver until
the LED confirms clear communication. Proper communication between the transmitter
and wireless receiver is verified when for each press or release of the tamper switch, the
transmitter’s LED blinks immediately on and immediately off.
ADDITIONAL INFORMATION
Black
Green
Yellow
Red
J4
RED PRO
J8
XT30/XT50 Series Panel
J7
RJ SUP
AC
1234 5 6 7 810 11 12
9
+B BELL GND SMK
RED YEL GRN BLK
AC -B
Can be extended
up to 500 feet
from the panel
using 22 AWG
1100D
Receiver
Figure 2: Wiring the 1100D to the Panel
LED INDICATIONS
RF RX Flashing yellow indicates
data is being received from a
transmitter.
RF TX Flashing green indicates data is
being sent to a transmitter.
PANEL RX Flashing yellow indicates data
is being received from a panel.
PANEL TX Flashing green indicates data is
being sent to the panel.
STATUS Solid red indicates memory is
being uploaded. Turns off when
complete.
PWR Solid green indicates there is
power to the wireless receiver.
Table 1: LED Indications
Mounting Holes

1100D INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3
Transmitter Supervision Time
For listed installations, program the transmitter supervision time in panel zone programming
as listed in the following table. Refer to the panel programming guide for complete wireless
programming information.
UL STANDARD LISTED ACCESSORIES SUPERVISION
TIME
UL 268 Smoke‑Automatic Fire
Detectors
• 1100R Repeater
• 1164 Wireless Synchronized Smoke
Detector
3
UL 365 Police Station
Connected Burglar Accessory
• 1100R Repeater
• 1103 Universal Transmitter 60
UL 521 Heat Detectors for Fire
Protective Signaling Systems
• 1100R Repeater
• 1183‑135F, 1183‑135R 3
UL 609 Local Burglar Alarm
Units and System Accessory
• 1100R Repeater
• 1103 Universal Transmitter 60
UL 634 Connections and
Switches for use with Burglar
Alarm Systems Accessory
• 1100R Repeater
• 1101, 1102, 1103, 1106 Universal
Transmitters
60
UL 636 Holdup Alarm Units and
Systems Accessory • 1142 Two‑Button Holdup Transmitter 60
UL 639 Intrusion Detection
Units Accessory
• 1100R Repeater
• 1127W, 1127C PIR Motion Detectors 60
UL 985 Household Fire Warning
System Accessory
• 1100R Repeater
• 1135 Wireless Sounder
• 9060, 9063, 9862 Wireless Keypads
240
UL 1023 Household Burglary
System Units Accessory
• 1100R Repeater
• 1101, 1102, 1103, 1106 Universal
Transmitters
• 1127W, 1127C PIR Motion Detectors
• 1135 Wireless Sounder
• 1142 Two‑Button Holdup Transmitter
• 9060, 9063, 9862 Wireless Keypads
60
UL 1076 Proprietary Burglar
Alarm Units Accessory
• 1100R Repeater
• 1103 Universal Transmitter 60
UL 1610 Central Station Burglar
Alarm Units Accessory
• 1100R Repeater
• 1103 Universal Transmitter
• 1135 Wireless Sounder
• 9060, 9063, 9862 Wireless Keypads
60
Table 2: Wireless Transmitter Supervision TImes

Designed, engineered,
and manufactured in
Springfield, Missouri using U.S.
and global components.
LT-1820 19041
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
Ordering Information
1100D‑W Standard Wireless Receivers
1100DE‑W Encrypted Wireless Receivers
Intertek (ETL) Listed
ANSI/UL 365 Police Station Connected Burglar
ANSI/UL 609 Local Burglar Alarm Units & Systems
ANSI/UL 636 Holdup Alarm Units & Systems
ANSI/UL 985 Household Fire Warning Systems
ANSI/UL 1023 Household Burglar Alarm System Units
ANSI/UL 1076 Proprietary Burglar Alarm Units
ANSI/UL 1610 Central Station Burglar Alarm Units
Compatible With Devices Listed for:
ANSI/UL 634 Connections and Switches for use with Burglar Alarm
Systems Accessory
ANSI/UL 639 Intrusion Detections Units Accessory
1100D SERIES
WIRELESS RECEIVERS
Specifications
Operating Voltage 8 to 14VDC
Current Draw 40mA
Frequency Range 905‑924MHz
Housing Dimensions 5.5” W x 3.75” L x 1” H
Housing Color White
Housing Material Flame Retardant ABS
Certifications
California Stat Fire Marshal (CSFM)
FCC Part 15 Registration ID: CCKPC0114R6
Industry Canada: 5251A‑PC0114R6
Patents
U. S. Patent No. 7,239,236
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from
all persons. It must not be located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Information
This device complies with Industry Canada Licence‑exempt RSS standard(s). Subject to the following two conditions:
1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS‑102 and is in compliance with the limits specified by Health
Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general
bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites
établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces
(20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand
public.