DNA BHK900 User manual

BHK9000
Instruction Manual
BLUETOOTH HANDSFREE
www.dnaaudio.com.au
BLU
E
E
TOO
T
T
HH
A
A
NDS
F
F
RE
E
E
BLUETOOTH
HANDSFREE
BLUETOO
T
T
HHANDS
F
F
REE

2
Introduction
Congratulations on your purchase.
The BHK9000 incorporates the latest technology in Bluetooth
handsfree car kits designed for your daily in-car mobile communication
usage. Combing elegance and simplicity the BHK9000 is one of most
friendly handsfree car kits around. Using the stylishly designed wired
remote control you can easily operate Bluetooth handsfree functions
that allow you to pair with multiple phones so you can easily answer an
incoming call, or dial out the last number called without accessing your
mobile phone.
By using the BHK9000 handsfree car kit you can avoid receiving hefty
fines while not worrying about missing important calls while driving.
Preface
This publication, including all photographs, illustrations and software,
is protected under international copyright laws, with all rights reserved.
Neither this manual, nor any of the material contained herein, may be
reproduced without the express written consent of the manufacturer.
Trademarks
purposes only and may be trademarks and/or registered trademarks of
their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy
of this manual, the manufacturer and distributor assume no liability
resulting from errors or omissions in this manual or from the use of the
information contained herein.
Other product names mentioned herein are used for identification

3
Safety
Important Note on Safety!!
Please read the following notes before installing and using this car kit!
1. Unit Installation – Installing the BHK9000 Bluetooth
Handsfree Car Kit requires specialized knowledge and skills.
Incorrect installation may cause damage to your BHK9000 unit
and/or your vehicle! Therefore, it is strongly advised that the
system be installed by a qualified professional.
2. Installation Location – Unsuitable installation locations in
your vehicle may lead to incorrect functioning of the essential
vehicle safety equipments such as air bag or it may become a
source of injury in an accident situation. Please always consult
the professional installer and carefully choose the installation
location in your car.
3. Interference with on-board electronics – Incorrect
installation or unsuitable installation locations may cause
interference with the vehicle electronics systems. Please read
the vehicle manufacturer’s notes to the effect!
4. Road safety – We strongly advise that full attention is to be
paid to the traffic conditions whenever the vehicle is moving.
Distraction of attention can lead to dangerous traffic situation.
Even when using a handsfree car kit driver is always advised
to avoid phone call during difficult and complex traffic situation.
5. Use only approved replacement parts – Please always use
official parts for your car kit as unknown spare or replacement
parts may lead to malfunction.

4
Index
Introduction............................................................................ 2
Safety..................................................................................... 3
Contents
Package Contents.......................................................... 5
Installation
Installing the Contol Module........................................... 6
Connecting the Power Cable......................................... 7
Connecting Components............................................... 8
Installing the Wired Remote Control.............................. 9
Installing the Microphone............................................... 10
Car Kit Operation
Understanding your Wired Remote Control................... 11
Pairing Phones............................................................... 12
Operation....................................................................... 13 - 14
Resetting the Car Kit & Trouble Shooting...................... 15
Quick Reference Guide.......................................................... 16

5
Package Contents
Optional Components
Contents
Wired Remote
External Speaker
)64HPM(redloHenohPi)54HPM(redloHenohPeliboMOSI-0009KHB
Remote Holder
Power Cable
ediuGresUeludoMlortnoC
enohporciMteS
esuF
Note: If any items is missing or damaged, please contact your dealer.
BHK9000-ISO
ISO harness provides easy plug and play option for an ISO connection commonly
used in European vehicles. This integration automatically mutes your vehicles front
speakers for bluetooth audio. External bluetooth speaker supplied is not required for this
installation setup. Further infomation supplied with BHK9000-ISO harness.
BHK9000
Instruction Manual
BLUETOOTH HANDSFREE
www.dnaaudio.com.au
B
BLUE
ETOOT
TH
HA
ANDSF
FREE
BLUETOOTH
HANDSFREE
BLUETOOT
TH
HANDSF
FREE

6
This section demonstrates how to set up and install the BHK9000 into
a vehicle.
Installing the Control Module
The Car Kit is designed to work with either 12V or 24V vehicle supply
voltage. Refer to the following on how to install the control module in a
vehicle.
1. Locate a suitable place inside the car to mount the control module.
Select a dry place that avoids excessive heat and mechanical
vibration. Ideally, the control module should be hidden from view, but
still be easily accessible such as under the drivers dash area.
Note: Make sure that the cables are long enough to support the
location of the control module. If the cables are not long enough, do not
lengthen the cables. Instead, relocate the control module.
2. Use two screws to fasten the control module in place.
Installation

7
Connecting the Power Cable
The following illustration demonstrates how to connect the Car Kit’s
power cables to the vehicle’s electrical system.
IMPORTANT!
Ensure the supplied fuse holders and fuses are installed in the following
configuration.
RED WIRE: 5 Amp Fuse
BLUE WIRE: 2 Amp Fuse
BLACK WIRE: 2 Amp Fuse
Warning!!
1. The blue cable must be connected to the 12/24V switched IGN wiring
to enable the Car Kit to go into standby mode when turned OFF.
2. Do not connect the blue cable to permanent +12/24V. Doing so may
discharge the battery of the vehicle and prevent the Car Kit from
being reset.
3. Please do not attempt to install the unit by yourself. Always consult
professional installer for power cable installation.
Installation

8
Connecting Components
The following illustration shows where to connect component devices.
Installing the Wired Remote Control
Item Description
Wired Remote Control The wired remote control should be located
within reach and view of the driver.
Microphone Ideally, the microphone should be located in
front of the driver and above waist height.
Speaker For best reception, the speaker should be
mounted at least 80cm (30 inches) from the
Car Kit’s microphone.
Installation

9
Installation
Installing the Wired Remote Control
Find a suitable place for the wired remote control that will provide the
best visibility. Remove dust and grease from the surface and firmly press
the wired remote control holder in place with the sticker pads provided,
or screw the holder into a suitable location with the enclosed screws.
Slide the wired remote control into the holder.
Option 1
Sticker Pad
Option 2
Screws

10
Installation
Installing the Microphone
Before installing the microphone, take note of the following:
Ensure the microphone cable can reach the control module. If the
cable is too short, relocate the microphone or the control module.
Do not attempt to lengthen the cables.
The supplied microphone is uni-directional. For best results, place the
microphone in front of the person talking. It has a reception angle of 60
degrees, and is most effective within a 60cm radius.
Installing the Microphone
Find a suitable place (e.g. sun visor) for the microphone. Remove dust
and grease from the surface.
1. Remove the protective cover
from the sticker pad at the
bottom of the microphone.
2. Firmly press the microphone
with the sticker pad in place.

11
Understanding your Wired Remote Control
Car Kit Operation
Keypad Description
Answer/ Redial
Press to answer an incoming call, re-dial
the last call made, to hold or release a
call or receive another incoming call.
Volume Up Press to increase volume during
conversation.
Volume Down Press to decrease volume during the
conversation.
End / Reject
Press to end a conversation, reject
an incoming call, or activate voice dial
function in your phone.

12
Paring Phones
Pairing Phones
Your phone must be paired with the BHK9000 before you can operate
your handsfree car kit. To pair your phone, follow the procedure below.
Warning: Never attempt to pair your phone while driving.
1. Turn IGN to ‘ON’ and wait for the power up tone.
2. Press and hold the ANSWER and VOLUME DOWN buttons
at the same time until you hear two quick beeps and the blue
LED’s begins to flash (the system is now ready to be paired).
3. Be sure Bluetooth is enabled on your phone. Follow the
documentation provided with your phone to search for new
devices.
4. Select the DNA BHK9000 from the list of Bluetooth devices on
your phone.
5. Enter the passcode: 1234
6. The LED will turn to solid blue when the phone is paired and
connected.
Note: Up to three phones can be paired with this car kit. You may follow
the same procedure above to pair a second or third phone. Pairing a
fourth phone will cause the first paired phone to be deleted.
Operation with Multiple Paired Phones
When the ignition is turned ‘ON’ the BHK9000 begins to search for
paired phones. Priority is given to the most recently connected phone.
Example: Phone A is paired and connected first, phone B is paired and
connected second and phone C third.
If all three phones are in range when the ignition is turned ‘ON’ phone
C will establish a priority connection with the BHK9000.
Note:
If phone C is turned off or if the person using it leaves the car and goes out of range
the connection will be broken. In order to establish another connection with one of
the remaining phones, press the answer/redial button once or restart the ignition. The
BHK9000 performs another search and establishes a connection with the most recently
connected phone, in this example phone B.

13
Operation
Answering an Incoming Call and Last Call Redial
To answer an incoming call:
Press ANSWER button when hearing the incoming call ringtone.
To redial the last number made on your phone:
Press and hold the ANSWER button for 3 seconds until you hear a
beep. Car kit will activate the last call you made on your phone.
End an Active Call and Reject an Incoming Call
To end an active call:
END button during a call.
To reject an incoming call:
END button when hearing an incoming call.
Adjusting the Conversation Volume
To adjust the conversation volume:
Press VOLUME UP or VOLUME DOWN during an active call to
increase or decrease conversation volume respectively.
Call Waiting, 2nd Incoming Call and Privacy Call
To hold an active call:
ANSWER button during an active call.
To release a call that is on hold:
ANSWER button again to release the call from hold.
To receive another incoming call during a call:
Press ANSWER button when hearing the incoming call ring tone
during an active call.

14
Operation
Switching between handsfree and handset mode (Privacy Call):
 Activate the handset command on your phone to transfer between
handsfree and handset during a call.
Note: Follow the documentation provided with your phone to access
this setting.
Warning!!
It is illegal to use mobile phone while driving. Please check the law in
your region. We do not recommend useing the handset whilst driving.
Voice Dial
To activate voice dial function on your phone:
Press and hold End button for 3 seconds until you hear the voice dial
activation sound from BHK9000. Then wait for the voice dial tone
from your phone and speak the name clearly.
Note: Voice Dial is only applicable if your phone supports this function. Depending on
your phone model you may need to record the voice tag in prior to using this function.
Please refer to your phone manual or contact phone manufacturer for further information.
Further note on voice recognition: Voice recognition is a feature of your phone which
enables you to dial a number by simply saying a pre-recorded “voice tag”. This function is
only applicable if your phone supports this function. Depending on your phone model you
may need to record the voice tag in prior to using this function. Normally when you set
a voice tag, you speak directly into the phone. When accessing this feature with the Car
Kit, you may find it necessary to re-record the voice tag while you are in the car. This will
set not only the way you say the voice tag, but also record a familiar background noise.
Since phones are in continual contact with the car kit, it is possible to use the Car Kit’s
microphone to record the voice tag. Locate the feature on your mobile phone, and when
prompted for the voice tag, speak clearly and in normal speed.
This function accesses the voice recognition system in your phone. It can only work as
well as the phone works with this feature, furthermore your phone must support this
feature.

15
Resetting the Car Kit
If you are experiencing difficulty in connecting the phone with the car kit
or if you would like to delete all the previously paired phones you can
perform a master reset.
To master reset:
Press and hold the ANSWER and VOLUME DOWN button at the
same time. You will hear a tone (pairing mode), continue holding the
buttons until you hear the second tone.
Troubleshooting
For more trouble shooting information contact your place of purchase.
Resetting & Trouble Shooting
Issue Solutions
My mobile
phone will not
connect to the
BHK9000
Ensure pairing procedure was followed correctly.
Ensure the Bluetooth function on your phone is
enabled.
Ensure the car ignition is ‘ON’. If ‘ON’ and no power
please check the fuses and wiring.
Master reset the car kit and make another attempt.
 Turn your phone ‘OFF’ and ‘ON’ again then try again.
If your phone is very new check the support website
for an upgraded software version.
Call
disconnects
when
attempting to
adjust volume
With some phones, adjusting the volume before the
call is initiated will disconnect the call. Only adjust
the volume after answering the call.
My phone
cannot
recognise my
voice

Ensure windows are closed when using voice
recognition.
If your phone requires you to record a voice tag,
please record the voice tag using the car kit.
If your phone supports independent voice recognition
technology please speak clearly in normal speed.

www.dnaaudio.com.au
Function Operation Environment
Enter the pairing mode + Hold for 3 seconds
Pairing passkey 1234
Redial the last call
made Hold for 3 seconds
Answer an incoming
call
End a current call During a call
Reject an incoming call
Volume up During a call
Volume down During a call
Voice dial activation Hold For 3 Seconds
Handsfree to private
call Control From Your Phone During a call
Private call to
handsfree Control From Your Phone During a call
Call hold During a call
Call waiting When hearing
a second
incoming call
Quick Reference Guide
VERSION-USERINST20110308BHK9000
Item No.: DNA-USERV1