Dock N Stow GEN2 User manual

Thank you for purchasing a Dock N Stow product!
GEN2 Operation andInstruction
Read All Instructions! Failure to Follow All Instructions Listed Below May Result In An Unsafe or Dangerous
Condition.
Contents of package: 1 Dock N Stow; 4 grey spacers.
•Magnets need to be kept at a safe distance from all magnetic storage devices, electronics and credit cards etc....
•Insure that the magnet is stored inthe “OFF” position when not in contact with Ferromagnetic metals (such as iron). The magnet can be left ON or
OFF indefinitely without harm. When ON and near Ferromagnetic metals (such as steel) there will be a sudden and powerful attraction.
•DO NOT attempt todisassemble or alter the Dock N Stow magnet; there are no user serviceable parts inside the device.
•All Dock N Stow products are designed for normal conditions, do not use underwater or in a hazardous environment.
•DO NOT use the magnet if it is damaged oris not working properly. Severe injury can occur if this device is not used properly and safely.
•DO NOT expose the Dock NStow magnets to temperatures above 180 deg Fahrenheit (80 Celsius). High temperatures will permanently degrade the
magnet’s effectiveness and may result in an unsafe condition.
•This product contains PTFE lubricant. For MSDS information contact Dock N Stow.
•Always keep the bottom of your Dock N Stow clean and free of debris and rust.
Step 3 - Remove top insert if necessary for use with caster wheel.
•If a wheel is on the bottom of your jack post, remove top insert for wheel dock using Phillips head screwdriver.
Step 1 - Determine trailer frame location you will be using for your new frame mounted Dock N Stow stabilizer block. This location will need 7 inches of space.
Step 2 - Measure the top width of the trailer frame; This measurement is used to determine how many spacers are needed for your frame size.
•3-inch trailer frame requires no spacers.
•2.5 inch trailer frame requires two spacers. One spacer will be used on either side of the channel at the bottom of the block.
Slide spacers into dovetail grooves until they snap into the bottom of the block.
•2 inch trailer frame requires four spacers. Two spacers will be used on either side of the channel at the bottom of the block.
Slide spacers into dovetail grooves until they snap into the bottom of the block.
Dock N Stow Assembly:

WARNING
Failure to read, understand, and follow all instructions before using this device may result in personal injury or property damage.
WARNING
Visually inspect equipment prior to each use. If damage is apparent, remove from service. Prolonged exposure to sunlight can cause device to weaken. Always use
brake. Chock all tires on trailer, both in front and behind tires prior to use. Use only on hard, level surfaces. Never place yourself under or behind unstable vehicles. Do
not exceed the rated weight. Center the load on the Dock N Stow. Ensure the jack foot or post is flush with surface of Dock N Stow. Do not make any alterations to this
product. Not to be used with aluminum or non ferromagnetic material. Not to be used on any trailer with less than a 2-inch-wide trailer frame or greater than 3-inch
wide trailer frame. When not in use, securely fasten the Dock N Stow to the frame of the trailer prior to travel. Not intended for commercial use or with heavy
commercial-type trucks or trailers. Failure to heed warnings may result in personal injury and/or property damage. User assumes all risk for the proper use of this device
and for ensuring product suitability for intended application and safe securement to trailer before traveling.
Dock N Stow GEN2 is designed to be used only on ferromagnetic metals (such as steel) .
Dock N Stow Limited Warranty
Dock N Stow products are covered by a One Year Limited Warranty on Material and Workmanship. Warranty is Non-Transferable. Dock N Stow reserves the right to inspect
all product claims under warranty. Any alteration of the device voids this warranty. This warranty shall not cover any incidental or consequential damages due to the
improper use or failure of this device.
Usage: When ready to use Dock N Stow, make sure ground is level.
•Place Dock N Stow under trailer tongue jack. Lower jack and ensure post is centered on Dock N Stow and stable.
•Dock N Stow works with virtually all trailer tongue jacks; round, square, post, wheel.
Wheel
Post
Round Foot Square / Rectangle Foot
Storage:
Important Magnet Information
•Always test magnetic connection to ensure that it is capable of safely holding in-place be for travel.
•Numerous factors can negatively affect the strength of the magnetic bond, dirt, debris, rust, oils, grease, and any gap between the bottom of the block and
the metal surface will decrease the bond. Ensure that the connection point is clean and free of these factors.
•Thicker metals will be held more strongly than thinner metals. E.g. 1/4" (6mm) steel will be held more strongly than thin gauge metals.
•Never exceed the rated capacity of the magnet. Magnet has up to 85lbs of break-away Force under ideal conditions. Actual in-use results will vary
greatly, and user must test every bond to determine the suitability of the magnet to hold the material.
•Avoid sudden jerking orshock force as this will cause the magnet to lose its hold.
•For safe operation, the bottom surface of the Dock NStow must always be on flat and smooth surfaces.
•As with all precision devices, damage can occur from dropping, bumping and impact.
•Turn handle clockwise 180 degrees until it stops in order to be turned “ON” (see image A).
•It is not possible to hold magnet in place unless fully turned “ON”.
Step 2 - Turn magnet on.
•Ensure bottom surface of Dock N Stow is on flat smooth frame surface.
Step 1 - Place Dock N Stow on top of the frame rail of trailer. .
Image A
Step 3 - Turn magnet off.
•To turn magnet off, push the handle in, then turn counterclockwise until it stops. The
magnet will turn off and release upon turning the handle.