Dog Runner Tracks User manual

THE SPECIFICATIONS OF THIS PRODUCT MAY VARY FROM THIS PHOTO
AND ARE SUBJECT TO CHANGE WITHOUT NOTICE.
FOR MAXIMUM EFFECTIVENESS AND SAFETY, PLEASE READ THIS
USER’S MANUAL BEFORE USING YOUR TREADMILL.
User's Manual

IINDEX
1. OVERVIEW DRAWING ....................................... 2
2. IMPORTANT SAFETY INSTRUCTIONS ............ 3
3. GROUNDING WIRES INSTRUCTIONS............... 4
4. PRE-ASSEMBLY CHECK LIST ........................... 5
5. ASSEMBLY STEPS ............................................. 6
6. EMERGENCY STOP SYSTEM ........................... 8
7. MAINTENANCE ................................................... 9
8. COMPUTER OPERATION INSTRUCTIONS ...... 10
9. EXPLODED VIEW ................................................14
10. PARTS LIST .........................................................15
1

OVERVIEW DRAWING
2
Side rail cover (L)
Main frame welding
Computer
Safety key
Side rail cover (R)
Hooker rack

IMPORTANT SAFETY INSTRUCTIONS
3
Before using this treadmill, basic precautions should always be followed,
including the following:
● To ensure user safety and protect the unit, read all the instructions before assembling and using
the treadmill.
● Do not use this product outdoors, near swimming pools or in damp, wet locations.
● Assemble and operate the treadmill on a solid, level surface. Provide the following clearances: 1 m
(3 feet) at each side, 2 m (6 feet) at the back. Be sure the treadmill is clear of any obstructions,
including walls, furniture and other hard surface. Place a protective sheet below the treadmill to
protect the floor or carpet from possible damage. Check the treadmill before each use and verify
that all fasteners are secure.
● To reduce the risk of electrical shock, always unplug this treadmill from the electrical outlet
immediately after using it and before cleaning, attempting any maintenance tasks or before
removing the treadmill.
● Do not adjust the running belt when dog is standing on the treadmill.
● Keep the power cord away from heated surface and sharp edges.
● Never operate this treadmill if it has a damaged power cord or plug, if it is not working properly, if it
has been damaged or dropped or if it has been submerged in water. In these cases, this treadmill
should be examined by a qualified service technician.
● Do not modify or attempt any service on the treadmill yourself, seek trained repair personnel when
servicing. Contact the nearest authorized dealer or other competent repair service.
● Connect this treadmill to a properly grounded outlet only. Improper connection of the power cord
can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the treadmill is properly grounded. Do not modify the plug provided with the
treadmill. If it will not fit in the outlet, have a proper outlet installed by a qualified electrician.
● Do not use the treadmill in areas where aerosol spray products are being used or where oxygen is
being administered. Such substances create the danger of combustion and explosion.
● Do not use the treadmill if user exceed 70kgs. (155lbs).This is the rated maximum user weight.
● Keep the running belt clean and dry all times.
● Be sure the power cord has plenty of slack and does not get pinched underneath the treadmill
when it elevates and declines.
● Do not leave the treadmill unattended when plugged in and running. After turning off the treadmill,
don’t leave it until it comes to a complete stop and is level. To disconnect, turn all controls to the
STOP or OFF position, and then remove the plug from the outlet.
Note: Read all instructions and save for future use.
WARNING:
!

GROUNDING WIRES INSTRUCTIONS
4
The treadmill needs special power supply:
Power supply voltage (V) Frequency (HZ) Rated current (A)
100 50/60 18
120 50/60 18
200 50/60 9
220 50/60 9
230 50/60 9
240+ 50/60 9
DANGER!
Wirings follow the local country electrical regulations, high voltage, low voltage wires, and grounding
wires must be separately transported and can’t connect with or twist other wires. The product must be
grounded to prevent electric shock, but improperly connect grounding device of treadmill can also
lead to electric shock. If you are not sure whether the grounding device has been properly connected,
you can consult the electrician or service personnel. If the plug is not suitable for the power supply
socket, please do not replace the plug provided with the product, please ask professional electrician
for installation.
Figure
Grounding methods
Grounding end
Socket with grounding end

PRE-ASSEMBLY CHECK LIST
5
A
B
C
D
E
F
G
H
d
b
e
c
f
a
No. Description Q’ty
A Main frame welding 1
B Hooker rack 1
C Computer tube welding 1
D Computer 1
E Safety key 1
F L shaped Hex Wrench 1
G Cross wrench tool 1
H Silicon oil 1
No. Description Q’ty
a Hex screw 10
b Cap nut 4
c Truss phillips self tapping screw 2
d Curved washer 8
e Nylock 4
f Washer 2

6
Step 1.
ASSEMBLY STEPS
A
Rotate the left and right side doors (A)
upward.
Note: Firstly, rotate one side door and fixed by
screw, secondarily rotate the other side door
and fixed by screw.
Step 2.
Assemble right & left side doors by hex screw
(a), curved washer (d), and cap nut (b) . Use
L shaped hex wrench (F), Cross wrench tool
(G) as left figure shown.
Note: Not tighten the screw at this moment.
a
a
a
a
d
d
b
b
G
F
Step 3.
1. Unzip the zippers on left and right side door
covers.
2. There are three position holes on side rails
(L+R). Please put the Hooker rack (B) on
desired position holes on left and right side
rails respectively.
3. Assemble Hooker rack by hex screw (a),
curved washer (d), and cap nut (b) . Use L
shaped hex wrench (F), Cross wrench tool
(G) as left figure shown.
Note: The nut direction on hooker rack is
backwards, then tighten the screws on side
rails (L+R) and positioning screws as left
figure showing.
F
a
d
e
G
B

7
Step 4.
1. Pull out the wire and release wire through
console welding tube assembly (C).
2. Tighten computer welding tube assembly
(C) with Hex screw (a), washer (f) by hex
Wrench (F) as left figure showing.
Step 5.
1. Connect computer cable (D) with cable port
from computer welding tube assembly (C).
2. Align the computer screw column with the
computer tube hole ( C ).
3. Use cross wrench tool (G) to tighten the
Truss phillips self tapping screw (c) .
4. Attach the safety key ( E ) into computer
(D).
Step 6.
1. Finish assembly.
2. Turn on the power to check the machine if
can start functionally, if not, to check again if
the cable connection between computer ( C )
and computer welding assembly (D) if
connect properly.
F
a
f
C
Gc
E
D

ONDERHOUD
8
This treadmill is equipped with safety system. The safety key shown as below drawing, a cord
connects the security clip to the red STOP key on computer. User must attach the security clip to your
dog’s harness before to begin any workout.
Emergently stop treadmill by pulling the cord to suspend the operation.
To continue operation, please reinsert the safety key into the computer.
EMERGENCY STOP SYSTEM

9
Running Belt Adjustment
If the running belt is not in the center, stop the treadmill then adjust the Hex Screw in the Rear End
Cap by the Hex Wrench. For example, if the running belt is moving towards the left side, turn the left
Hex Screw about 1/4 circle (clockwise). If the running belt is moving towards the right side, turn the
right Hex Screw about 1/4 circle (clockwise). Turn on the treadmill after it has been adjusted. If you
find that the belt does not move to the proper position, please repeat above steps. Do not use the
treadmill until the running belt returns to the center position.
(Ps.1. This action is very important, if the belt is not in the center, be sure to follow above steps.)
(Ps.2. The position of the running belt might not stay precisely in the center with slightly towards the
left or right side, and the situation varies with how end-users use and the weight of end-users. No
need to adjust the belt if it does not rub against the parts aside.)
MAINTENANCE

COMPUTER OPERATION INSTRUCTIONS
10
PM
PM
1. COMPUTER DISPLAY DESCRIPTION:
1.1 SPEED
1.1.1 MAX SPEED：14.0KMH
1.1.2 MIN SPEED: 0.8KMH。
1.1.3 Display function
1.1.3.1 Exercise mode: Display current exercise speed value
1.1.3.2 Setting mode: 0.8 KM/H - 14.0 KM/H
1.1.3.3 Version display: Turn on power and start the machine, attach safety key, computer
display all read outs, speed read out shows software version No.
1.2 DISTANCE
1.2.1 In exercising mode : display range 0.0 – 999 (KM), over 999 will return to ZERO to start
new countdown. DIS icon will flash.
1.2.2 In setting mode: Setting range 1.0 – 999 KM/MIL, adjustment step 1.0 KM/MIL per time,
DIS icon will flash when set countdown mode.
1.2.3 In exercising mode: DISTANCE read out display range 0-999, only display round number,
over 1000 will retrun to ZERO to start new countdown.
1.3 TIME
1.3.1 In exercising mode: TIME read out display range 0:00 – 99:59 (Minutes: Second) , over
99:59 will retrun to ZERO to start new countdown.
1.3.2 In setting mode: Setting range 5:00 – 99:00, set stepping 1.00 ,TIME icon will flash when
set countdown mode.
1.4 CALORIES
1.4.1 In exercising mode: CALORIES read out display range 0-999, over 99:59 will retrun to
ZERO to start new countdown, CAL ICON will flash.
1.4.2 In setting mode: Setting range 5:00 – 99:00, set stepping 1.00, TIME icon will flash when
set countdown mode.
2. Computer Operation Instruciton :
2.1 Operation Instruction – Power on display -
2.1.1 After turn on machine without putting on safety key, all data display as “- - -” beeper makes
“beep” sound.
2.1.2 After put on safety-key, SPEED window display shows “Version No.”, other window display
with flash for 1 second, then all data display resume to ZERO.
2.1.3 Turn on machine display: recognize program, under countdown mode, press “START”
button, widow display shows 3 – 2 – 1 with beep to count down then machine starts.
2.2 Button Functions:
2.2.1 START - At the time of treadmill stand-by mode, Program mode and Time countdown
mode, press the START button, console displays set speed. Treadmill starts aftter
countdown for 3 seconds.
STOP - During treadmill running when press STOP button, the treadmill will decrease
speed until stop. After machine stop completely, the treadmill returns to stand-by mode and
all workout data return to zero.
2.2.2 PROGRAM button - Under stand-by condition, this button can alternatively choose manual
mode or Pre-set program. Pre-set programs have P01 – P04.
2.2.2.1 Default time countdown mode: TIME window display”30 :00” and flash, Use “SPEED”
button +/- to adjust time setting, range: 5:00-99:00, each adjustment: 1:00.
2.2.2.2 Each program running to finish, machine will stop gradually, TIME window display
END,O, beep sound with flash for 10 seconds, then all data return to ZERO and
resume to stand-by condition.

11
1. COMPUTER DISPLAY DESCRIPTION:
1.1 SPEED
1.1.1 MAX SPEED：14.0KMH
1.1.2 MIN SPEED: 0.8KMH。
1.1.3 Display function
1.1.3.1 Exercise mode: Display current exercise speed value
1.1.3.2 Setting mode: 0.8 KM/H - 14.0 KM/H
1.1.3.3 Version display: Turn on power and start the machine, attach safety key, computer
display all read outs, speed read out shows software version No.
1.2 DISTANCE
1.2.1 In exercising mode : display range 0.0 – 999 (KM), over 999 will return to ZERO to start
new countdown. DIS icon will flash.
1.2.2 In setting mode: Setting range 1.0 – 999 KM/MIL, adjustment step 1.0 KM/MIL per time,
DIS icon will flash when set countdown mode.
1.2.3 In exercising mode: DISTANCE read out display range 0-999, only display round number,
over 1000 will retrun to ZERO to start new countdown.
1.3 TIME
1.3.1 In exercising mode: TIME read out display range 0:00 – 99:59 (Minutes: Second) , over
99:59 will retrun to ZERO to start new countdown.
1.3.2 In setting mode: Setting range 5:00 – 99:00, set stepping 1.00 ,TIME icon will flash when
set countdown mode.
1.4 CALORIES
1.4.1 In exercising mode: CALORIES read out display range 0-999, over 99:59 will retrun to
ZERO to start new countdown, CAL ICON will flash.
1.4.2 In setting mode: Setting range 5:00 – 99:00, set stepping 1.00, TIME icon will flash when
set countdown mode.
2. Computer Operation Instruciton :
2.1 Operation Instruction – Power on display -
2.1.1 After turn on machine without putting on safety key, all data display as “- - -” beeper makes
“beep” sound.
2.1.2 After put on safety-key, SPEED window display shows “Version No.”, other window display
with flash for 1 second, then all data display resume to ZERO.
2.1.3 Turn on machine display: recognize program, under countdown mode, press “START”
button, widow display shows 3 – 2 – 1 with beep to count down then machine starts.
2.2 Button Functions:
2.2.1 START - At the time of treadmill stand-by mode, Program mode and Time countdown
mode, press the START button, console displays set speed. Treadmill starts aftter
countdown for 3 seconds.
STOP - During treadmill running when press STOP button, the treadmill will decrease
speed until stop. After machine stop completely, the treadmill returns to stand-by mode and
all workout data return to zero.
2.2.2 PROGRAM button - Under stand-by condition, this button can alternatively choose manual
mode or Pre-set program. Pre-set programs have P01 – P04.
2.2.2.1 Default time countdown mode: TIME window display”30 :00” and flash, Use “SPEED”
button +/- to adjust time setting, range: 5:00-99:00, each adjustment: 1:00.
2.2.2.2 Each program running to finish, machine will stop gradually, TIME window display
END,O, beep sound with flash for 10 seconds, then all data return to ZERO and
resume to stand-by condition.

2.2.2.3 Program Table:
4 Pre-set programs P01-P04 as following listed. Each pre-set program has 10 different
segments with varied speed and tme for each segment as below illustrated.
2.2.3 MODE button - Under stand-by condition, press this button can alternatively choose manual
mode to time countdown mode, distance countdown mode, calories countdown mode.
2.2.3.1 In time countdown mode, default time is 30:00 (minute), user can use “SPEED” button
+/- to adjust target workout time. Time countdown range: 5:00-99:00, each adjustment
is 1:00, default starting speed is at : 0.8 km/h.
2.2.3.2 In distance countdown mode, default distance is 1.0 (km), user can use “SPEED”
button +/- to adjust target workout distance. Distance countdown range is : 1:00-999,
each adjustment is 1:00, default starting speed is at : 0.8 km/h.
2.2.3.3 In calories countdown mode, default calories is 50 (kcal), user can use “SPEED” button
+/- to adjust target workout calories. Calories countdown range is : 20-990, each
adjustment is 20, default starting speed is at : 0.8 km/h..
2.2.4 SPEED +/- button - After starting machine, can use for adjusting speed, each adjustment is
0.1km, if press the button after more than 2 seconds, will continuously increase speed or
decrease speed.
2.3 Computer Instructions:
2.4.1 Computer display descriptions:
2.4.2 Display function:
2.4.2.1 Speed: Display current exercise speed value.
2.4.2.2 Time display: Shows the running time in manual mode or the countdown of running
time in countdown mode.
2.4.2.3 Distance display: Shows the accumulated distance under manual or program mode, or
the countdown of distance in running mode.
2.4.2.4 Calorie display: Shows calories accumulated during exercise in manual and program
modes, or countdown of calories in running mode.
1 2 3 4 5 6 7 8 9 10
P01 Speed 4 6 8 10 12 12 10 8 6 4
P02 Speed 6 8 10 12 13 13 12 10 8 6
P03 Speed 8 10 11 12 13 13 12 11 10 8
P04 Speed User setting program – can customized program
for speed and incline can be saved.
12
2.4.2.5 Computer Window Topic and Display Range:

13
2.2.2.3 Program Table:
4 Pre-set programs P01-P04 as following listed. Each pre-set program has 10 different
segments with varied speed and tme for each segment as below illustrated.
2.2.3 MODE button - Under stand-by condition, press this button can alternatively choose manual
mode to time countdown mode, distance countdown mode, calories countdown mode.
2.2.3.1 In time countdown mode, default time is 30:00 (minute), user can use “SPEED” button
+/- to adjust target workout time. Time countdown range: 5:00-99:00, each adjustment
is 1:00, default starting speed is at : 0.8 km/h.
2.2.3.2 In distance countdown mode, default distance is 1.0 (km), user can use “SPEED”
button +/- to adjust target workout distance. Distance countdown range is : 1:00-999,
each adjustment is 1:00, default starting speed is at : 0.8 km/h.
2.2.3.3 In calories countdown mode, default calories is 50 (kcal), user can use “SPEED” button
+/- to adjust target workout calories. Calories countdown range is : 20-990, each
adjustment is 20, default starting speed is at : 0.8 km/h..
2.2.4 SPEED +/- button - After starting machine, can use for adjusting speed, each adjustment is
0.1km, if press the button after more than 2 seconds, will continuously increase speed or
decrease speed.
2.3 Computer Instructions:
2.4.1 Computer display descriptions:
2.4.2 Display function:
2.4.2.1 Speed: Display current exercise speed value.
2.4.2.2 Time display: Shows the running time in manual mode or the countdown of running
time in countdown mode.
2.4.2.3 Distance display: Shows the accumulated distance under manual or program mode, or
the countdown of distance in running mode.
2.4.2.4 Calorie display: Shows calories accumulated during exercise in manual and program
modes, or countdown of calories in running mode.
2.4.2.5 Computer Window Topic and Display Range:
2.4.3 Increase speed: 0.5 KM/S, decrease speed: 0.5KM/S.
Window Topic Display Range
SPEED 1) Min 0.8-Max 14.0 (KPH), adjustment step 0.1/
per time.
2) Will show version no. right after power on.
DISTANCE 1) In exercising mode: 0.0-999 (KM).
2) In setting mode: 1.0-999 (KM), adjustment step 1
km/ per time.
TIME 1) In exercising mode: 0:00-99:59 (Minute:Second),
2) In setting mode: 5:00-99:00 (Minute:Second),
adjustment step 1 min/ per time
CALORIES 1) In exercising mode: 0-999 (CAL)
2) In setting mode: 20-990, adjustment step 10 cal/
per time

EXPLODED VIEW
14
01
02
03
04
05
06
06
07 08 09
10
11
12
12
12
13 14
15
17
18
19
20
21
25 22
22
22
22
23
23
24
26
27
28
29
30
31
33
33
34
34
35
35
36
37
37
38
39
39
39
39
40
41
41
05
32
22
39
02
23
26
16
16
16
12
12
22
22
39
39
39
39
38
12
12
17
17
17
42
42
43
43
44
45
46
47
48
47
48
49
50
43
43
43
43
51
51
52
53
54
56
55
55
57
58 59
58
60
60
43
43
43
43
47
43
43
43
43
43
43
61
61
61
61
39
39
62 63
64
31
17
17
17
27
23
26
32
36
47
48
65

No. Description Q’TY Spec.
01 Main frame welding 1 SGP2XA00
02 Metal guard rails 2 B00SGP2X
03 Console welding tube assembly 1 C00SGP2X
04 Hooker rack 1 D00SGP2X
05 Square end cap 2 PP502515
06 Square end cap 2 PP132612
07 Power cord retaining ring 1 PL6P-4
08 Overload switch 1 FL2-6A
09 I/O switch 1 FK5
10 Power cord 1 FD22100
11 Controller 1 F900135-220V
12 Truss phillips screw 7 M5*15
13 Single cable 1 FD16100R
14 Single cable 1 FD16200R
15 Control cable-lower 1 FKX7804P
16 Retaining ring 3 PY105mm
17 Washer phillips drilling screw 15 Φ4*16
18 Truss phillips & internal tooth screw 1 M5*8
19 Drive belt 1 PD200J7
20 Motor 1 FMDSGP2X
21 Ferrite core 1 FC311913
22 Curved washer 10 Φ8 ×Φ19 × 1.5T
23 Spring washer 7 Φ8X1.5T
24 Hex screw 2 M8X12
25 Motor fixing plate 1 MD1000A
26 Washer 5 Φ8.5*Φ23*1.5t
27 Truss hex screw 4 M8X15
28 Truss hex screw 1 M8*65
29 Running belt 1 400279514P
30 Running board 1 WP121048015
31 Rubber cushion 6 PY93010
32 Flat hex screw 8 M8*25
PARTS LIST
15

16
No. Description Q’TY Spec.
33 Belt blocking sheet 2 NZ1155425
34 Washer phillips self tapping screw 4 Φ4*12
35 Manual Incline base 2 PS1426339
36 EVA pad 2 80X20X4.0t
37 Pop pin knob 2 SCM1050
38 Truss hex screw 2 M8*50*15mm
39 Nylock 4 Φ4*12
40 Lower motor cover 2 PS1426339
41 Footrail 2 80X20X4.0t
42 Transportation wheel 2 SCM1050
43 Truss hex screw 8 M8*50*15mm
44 Motor cover 2 M8XP1.25
45 Front roller 1 PMDXSGP2X
46 Rear roller 1 PB123730
47 Washer 3 PY602085
48 Socket hex screw 1 M8*40*15mm
49 Side rail cover (L) 4 PMDSGP2X
50 Side rail cover (R) 2 NQGSGP2X
51 Flat round end cap 2 NQHSGP2X
52 Flat oval end cap 1 Φ8.5*Φ18*1.5t
53 Front Rack hooker 1 M8*1.25*55
54 Computer upper cover 1 WBSGP2X-L
55 Truss phillips self tapping screw 6 WBSGP2X-R
56 Inner computer cover 1 PPY3815
57 Upper control board + Control box key board 1 PPT255015
58 Round phillips self tapping screw 8 SW8746M8
59 Control cable-upper 1 PDSGP01-S
60 Truss phillips self tapping screw 2 Φ4*12L
61 Cap nut 4 PDSGP01-L
62 L shaped Hex Wrench 1 LCD3.5SGP01
63 Cross wrench tool 1 Φ2.3*6L
64 Safety key 1 FKS1504PIN
65 Silicon oil 1 Φ4*25L

ORIGINAL PRODUCT OF DOG RUNNER INTERNATIONAL
- Designed in Belgium - Europe -