Dolby Laboratories SEU4 Operation manual

MODEL SEU4
Surround Encoder
Users' Information
MAIN

USERS' MANUAL
FOR
MODEL SEU4
SURROUND ENCODER
Dolby Laboratories Inc
U.S.A. 100 Potrero Avenue, San Francisco, CA 94103-4813
Tel: [phone]; Fax: [phone]
U.K. Wootton Bassett, Wiltshire SN4 8QJ
Tel: [phone]; Fax: [phone]
www.dolby.com
WARRANTY INFORMATION, USA: warranty on the product covered by this manual is subject to the limitations and disclaimers set forth
in the warranty disclaimer originally shipped with the product and also printed on the back of the invoice.
All requests for repairs or information should include the unit serial number to ensure rapid service.
Dolby is a registered trademark of Dolby Laboratories.
©1997 Dolby Laboratories
SEU4-CE
ISSUE 4
S97/11562
Dolby Part No. 91436
MAIN

i
TABLE OF CONTENTS
SECTION 1 INTRODUCTION
1.1 Introduction ................................................................................................................................. 1-1
1.2 Specifications ............................................................................................................................... 1-2
SECTION 2 CONNECTIONS
2.1 Remote Connector J507 .............................................................................................................. 2-1
2.2 Power and Fusing ....................................................................................................................... 2-2
2.2.1 230V-Only SEU4.......................................................................................................................... 2-2
2.2.2 Multi-Voltage SEU4 .................................................................................................................... 2-2
2.3 Ground ......................................................................................................................................... 2-3
2.4 Audio ............................................................................................................................................ 2-3
2.5 Regulatory Notices ..................................................................................................................... 2-3
SECTION 3 CALIBRATION
3.1 General ......................................................................................................................................... 3-1
3.2 Items Needed............................................................................................................................... 3-1
3.3 Calibration ................................................................................................................................... 3-1
SECTION 4 BLOCK DIAGRAM
....................................................................................................................................................... 4-1
APPENDIX
Dolby Surround: Getting Started
Studio Questionnaire
Technical Requirements for Dolby Surround in Recording Studios
"Phase Correctors" and Dolby Surround
MAIN

1-1
SECTION 1
INTRODUCTION
1.1 Introduction
The Model SEU4 is used to generate Dolby Surround program material. The SEU4
contains a precision four-to-two spatial encoding network that is used to combine four
directionally allocated input signals (Left, Center, Right and Surround) into a two-channel
distribution pair. The two-channel output of the SEU4 contains the original four-channel
directional information in a matrix encoded form that allows subsequent decoding by
suitable consumer or professional decoding devices into four channel materials.
The SEU4 encoder is designed to be used in conjunction with the companion SDU4
Surround Decoder. Satisfactory generation of program material for surround encoding
requires mixing and monitoring using what is known as the “4-2-4” technique. A four-
channel mix is prepared and sent to the input of the SEU4 Surround Encoder via the
mixing console. The SEU4 generates a pair of channels that are recorded for subsequent
distribution. Simultaneously, the two-channel material is decoded using the SDU4 and
monitored in the mixing environment. This allows mixing engineers to adjust the mix
content in real time to fit the final playback environment. The 4-2-4 technique is essential
not only to produce successful surround material, but also to guarantee compatibility in
conventional stereo and monophonic playback.
Typically, the two channels generated by the SEU4 are distributed by conventional stereo
means such as consumer video formats and broadcast systems. Listeners who wish to
recreate four-channel input material can optionally decode the program material using a
surround decoding device. These are being manufactured by many consumer equipment
manufacturers and can be identified by a Dolby Surround logo on the equipment.
Home decoding of the two-channel output of the SEU4 is considered desirable but
optional. The two-channel material from the SEU4 is compatible with non-decoded, two
loudspeaker playback. The two-channel output of the SEU4 can also be considered to be
mono-compatible provided the original four-channel program material has been allocated
in a manner consistent with monophonic playback.
Note:
The Model SEU4 is not designed for mastering Dolby film sound formats. Dolby film
formats can only be produced with a valid Dolby Film Service agreement under
supervision of a Dolby Film Sound consultant. For further information please contact
Dolby Laboratories.
MAIN

1-2
1.2 Specifications
Layout:
1U rack-mount unit incorporating a
professional surround encoder module,
interface circuitry, and power supply.
Signal Connections:
Left, Center, Right and Surround XLR inputs.
Lt (Left total) and Rt (Right total) XLR
outputs.
EPL (External Process Loop) XLR sends and
returns.
(All XLR connectors wired pin2 “hot.“ For
unbalanced operation, at the SEU4 end
connect cables exactly as for balanced circuits
and unbalance the circuit only at the remote
end.)
Front Panel Controls and Indicators:
Ten screwdriver adjustable trim controls:
Left, Center, Right, and Surround input; Lt
and Rt External Processor Loop (EPL) send;
Lt and Rt EPL return; Lt and Rtmain
outputs. Four segment LED meters for each
input L,C,R, and S; LED surround active
indicator and 2 LEDs for EPL status.
Input Circuit:
(0 dBr = 0.775V rms)
Four balanced floating transformerless
inputs. Input gain adjustment will
accommodate a range of 300mV (–8.2dBr) to
2V rms (+8.2dBr). Input impedance is
greater than 10kohms. Maximum common
mode voltage 4 V rms, 5.8 V peak.
Output Circuit:
Two balanced floating transformerless
outputs. Output gain adjustment will
accommodate a range of 250mV (–9.8dBr)
to 2.5 V (10.2dBr).
Output impedance 25ohms.
Maximum output voltage +26dBr into
balanced 600 ohm load, less into lower
impedances. Maximum output +20dBr into
unbalanced 600ohm load.
External Processor Loop:
A two-channel EPL is provided for interface
with other equipment. The loop is engaged
by an internal switch and allows external
processing to be inserted via EPL input and
output connectors.
Overall Frequency Response:
20Hz—20kHz ±1dB (L, C, andR inputs).
100Hz—7kHz ±3dB (surround input).
S/N Ratio: (referenced to Dolby level)
Greater than 80dB, CCIR/ARM weighted.
Distortion:
Total Harmonic Distortion (THD) at themain
balanced outputs will not exceed 0.25% into
balanced loads 600 ohms or greater at any
output level to 12.5V rms. THD at Dolby
level at 1kHz with input and output adjusted
for 4dBr, 0.1% typical.
Ambient Operating Temperature:
Up to 40 degrees C.
Construction:
Two plug in modules: one Dolby surround
encoder and one interface module.
Fiberglass printed circuit cards, gold-plated
edge connectors, solid-state devices
throughout.
Size:
1 rack unit 43mm (1.75") high, 260mm
(10.25") deep behind mounting
surface;maximum projection in front of
mounting surface 7mm (0.28").
Weight:
5 kg, (11 lb.)
Power Requirements:
The SEU4 consumes about 20 watts and is
designed for operation from a centrally
switched power source. 230 V version: 198-
264 V ac, 50/60 Hz, uses one 20 mm T250 mA
fuse. Multi-voltage version: 85-132 V ac, 50/
60 Hz, uses one 1.25" 500 mA slow-blow fuse,
or 187-264 V ac, 50/60 Hz, uses one 20mm
T250 mA fuse.
Specifications subject to change without
notice.
MAIN

2-1
SECTION 2
CONNECTIONS
The SEU4 is a one-unit high chassis containing power supply, input/output connectors
and two plug-in circuit boards, a Cat. No.338 surround encoder and Cat. No.385 input/
output board.
Audio inputs and outputs use three-pin XLR connectors. All inputs and outputs have
level adjustments to match studio line levels. The unit has a two-channel external
processor loop to allow the insertion of external equipment such as a peak limiter; a link
between pins 6 and 7 of the remote control connector on the rear (J507) engages this loop.
2.1 Remote Connector J507
The SEU4 has a 15-pin female D-type connector that provides signals for remote metering
and control. For optimum immunity to rf interference, use shielded cable and connect the
shield to the metal housing of the male D-connector, not to one of the pins.
J507 Pin No. Function
1 (500mV) ................ Surround line in meter point
2 (500mV) ................ Right line in meter point
3 (500mV) ................ Center line in meter point
4 (500mV) ................ Left line in meter point
5 ................................ Link to signal ground to disable surround channel*
6 ................................ Link to signal ground for External Processor Loop On
7 ................................ Signal ground
8 ................................ Chassis ground
9
10
11
12
13 (500mV) .............. LT output meter point
14 (500mV) .............. RT output meter point
15 .............................. Signal ground
*J511 on the I/O board is set in ACTIVE HI position when shipped. With J511 set this way,
grounding D-connector J507 pin 5 will disable the surround channel. J511 can be changed to
accommodate ACTIVE LO control logic; with this setting of J511, grounding D-connector pin 5 will
enable the surround channel.
MAIN

2-2
2.2 Power and Fusing
2.2.1 230V-Only SEU4
OPEN THE
DOOR
OPENTHE
DOOR
ACTIVE
FUSE
FUSE
CARRIER
INSTALL
FUSE
METAL CLIP INSTALLED
ON UNUSED SIDE OF
CARRIER
TOP
Figure 2.1 Fuse compartment, 230V unit
Open the fuse compartment door in the AC mains input connector with a small flat blade
screwdriver (see Figure 2.1), and check that the fuse has the correct rating (T250mA 20mm
time-lag). The fuse carrier must be inserted into the compartment with the orientation as
shown. Do not force the carrier into the compartment. Damage will result.
2.2.2 Multi-Voltage SEU4
OPEN THE
DOOR
SPARE FUSE
(UPPER)
FUSE
ACTIVE
FUSE CARRIER
(LOWER)
FUSE
OCTAGONAL PEG
ROUND PEG
VOLTAGE SELECTOR
WHEEL
A2F4037
Figure 2.2 Fuse compartment, multi-voltage unit
Open the fuse compartment door in the AC mains input connector with a small flat blade
screwdriver(seeFigure2.2),andcheckthatthefusehasthecorrectrating. Ifnecessary,rotate
the selector drum until it displays the correct voltage for the installation. (The drum may also
be removed and replaced in the desired position. It will only fit one way around.) Snap the
fuse compartment door closed .
For 85 to 132 Vac use 500 mA 1.25" slow-blow fuse.
For 187 to 264 Vac use T250 mA 20mm time-lag fuse.
MAIN

2-3
2.3 Ground
It is normal practice to connect signal ground to power line ground for many reasons
including safety. In the SEU4 they are linked by a jumper on the input/output board
inside the unit.
On occasion, hum can be reduced by separating the two grounds. If this is necessary,
remove the front panel (2 screws on top and 5 along the bottom) and the top cover (2
screws each side), and move the jumper at the rear left of the unit (J510) to the “holder”
position. There is a 1 k ohm resistor across the link, so the signal ground is never totally
isolated from the chassis.
Note that the chassis is always connected to the ground pin of the power line cord; for
safety reasons, this ground MUST NEVER be disconnected
2.4 Audio Connections
The SEU4 has been designed to interface with professional audio equipment at commonly
found studio operating levels. Connections to and from the unit are made using standard
3-PinXLR-typeconnectors. Boththeinputandoutputstagesareelectronicallybalancedwith
pin 2 being positive and pin 3 being negative. For optimum immunity to radio-frequency
interference, cable shields should be connected to the shells of the XLR connectors, not to
pin1. For unbalanced operation, at the SEU4 end connect cables exactly as for balanced
circuits and unbalance the circuit only at the remote end.
2.5 Regulatory Notices
UL
Troubleshooting must be performed by trained technicians. Do not attempt to service the
unit unless you are qualified to do so.
WARNING: Check that the units have been set to the correct supply voltage and that the
correct fuses have been installed. To reduce the risk of fire, replace the fuses only with
the same type and rating. Do not use a ground-lifting adaptor and never cut the ground
pin on the three-prong power plug.
MAIN

2-4
UK
Connections for United Kingdom:
WARNING: THIS APPARATUS MUST BE EARTHED.
As the colours of the cores in the mains lead may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
• The core which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter Eor by the earth symbol , or coloured green or green and yellow.
• The core which is coloured blue must be connected to the terminal which is marked with the letter
Nor coloured black.
• The core which is coloured brown must be connected to the terminal which is marked with the
letter Lor coloured red.
EUROPEAN EMC
The 230V unit complies with the EMC requirements of EN 50081-1, EN 50082-1, prEN
55103-1 and -2 when installed in an E2 environment in accordance with this manual.
MAIN

2-5
GB
F
D
I
IMPORTANT SAFETY NOTICE
This unit complies with the safety standard IEC65. To ensure safe operation and to guard
against potential shock hazard or risk of fire, the following must be observed:
• Ensure the voltage selector is set to the correct mains voltage for your supply.
• Ensure fuses fitted are the correct rating and type as marked on the unit.
• The unit must be earthed by connecting to a correctly wired and earthed power outlet.
• The power cord supplied with this unit must be wired as follows:
Live—Brown Neutral—Blue Earth—Green/Yellow
IMPORTANT – NOTE DE SECURITE
Ce materiel est conforme à la norme IEC65. Pour vous assurer d'un fonctionnement sans danger et de prévenir
tout choc électrique ou tout risque d'incendie, veillez à observer les recommandations suivantes.
• Le selecteur de tension doit être placé sur la valeur correspondante à votre alimentation réseau.
• Les fusibles doivent correspondre à la valeur indiquée sur le materiel.
• Le materiel doit être correctement relié à la terre.
• Le cordon secteur livré avec le materiel doit être cablé de la manière suivante:
Phase—Brun Neutre—Bleu Terre—Vert/Jaune
WICHTIGER SICHERHEITSHINWEIS
Dieses Gerät entspricht der Sicherheitsnorm IEC65. Für das sichere Funktionieren des Gerätes und zur
Unfallverhütung (elektrischer Schlag, Feuer) sind die folgenden Regeln unbedingt einzuhalten:
• Der Spannungswähler muß auf Ihre Netzspannung eingestellt sein.
• Die Sicherungen müssen in Type und Stromwert mit den Angaben auf dem Gerät übereinstimmen.
• Die Erdung des Gerätes muß über eine geerdete Steckdose gewährleistet sein.
• Das mitgelieferte Netzkabel muß wie folgt verdrahtet werden:
Phase—braun Nulleiter—blau Erde—grün/gelb
NORME DI SICUREZZA – IMPORTANTE
Questa apparecchiatura è stata costruita in accordo alle norme di sicurezza IEC 65. Per una perfetta sicurezza
ed al fine di evitare eventuali rischi di scossa êlettrica o d'incendio vanno osservate le seguenti misure di
sicurezza:
• Assicurarsi che il selettore di cambio tensione sia posizionato sul valore corretto.
• Assicurarsi che la portata ed il tipo di fusibili siano quelli prescritti dalla casa costruttrice.
• L'apparecchiatura deve avere un collegamento di messa a terra ben eseguito; anche la connessione rete
deve avere un collegamento a terra.
• Il cavo di alimentazione a corredo dell'apparecchiatura deve essere collegato come segue:
Filo tensione—Marrone Neutro—Blu Massa—Verde/Giallo
AVISO IMPORTANTE DE SEGURIDAD
Esta unidad cumple con la norma de seguridad IEC65. Para asegurarse un funcionamiento
seguro y prevenir cualquier posible peligro de descarga o riesgo de incendio, se han de observar
las siguientes precauciones:
• Asegúrese que el selector de tensión esté ajustado a la tensión correcta para su alimentación.
• Asegúrese que los fusibles colocados son del tipo y valor correctos, tal como se marca en la unidad.
• La unidad debe ser puesta a tierra, conectándola a un conector de red correctamente cableado y puesto a
tierra.
• El cable de red suministrado con esta unidad, debe ser cableado como sigue:
Vivo—Marrón Neutro—Azul Tierra—Verde/Amarillo
VIKTIGA SÄKERHETSÅTGÄRDER!
Denna enhet uppfyller säkerhetsstandard IEC65. För att garantera säkerheten och gardera mot
eventuell elchock eller brandrisk, måste följande observeras:
• Kontrollera att spänningsväljaren är inställd på korrekt nätspänning.
• Konrollera att säkringarna är av rätt typ och för rätt strömstyrka så som anvisningarna på enheten föreskriver.
• Enheten måste vara jordad genom anslutning till ett korrekt kopplat och jordat el-uttag.
• El-sladden som medföljer denna enhet måste kopplas enligt foljande:
Fas—Brun Neutral—Blå Jord—Grön/Gul
BELANGRIJK VEILIGHEIDS-VOORSCHRIFT:
Deze unit voldoet aan de IEC65 veiligheids-standaards. Voor een veilig gebruik en om het gevaar van electrische
schokken en het risico van brand te vermijden, dienen de volgende regels in acht te worden genomen:
• Controleer of de spanningscaroussel op het juiste Voltage staat.
• Gebruik alleen zekeringen van de aangegeven typen en waarden.
• Aansluiting van de unit alleen aan een geaarde wandcontactdoos.
• De netkabel die met de unit wordt geleverd, moet als volgt worden aangesloten:
Fase—Bruin Nul—Blauw Aarde—Groen/Geel
E
S
NL
IEC NOTICES
MAIN

3-1
SECTION 3
CALIBRATION
3.1 General
The SEU4 is easily calibrated using an external tone, but consideration must be given to
the level this tone has in relation to the levels in the remainder of the recording system.
An external 1 kHz test tone is used to calibrate the Dolby Models SEU4/SDU4 encode/
decode combination. The tone should be set to the studio’s standard level, i.e., +4dBr or
0VU, etc. The SEU4 can be calibrated for input levels ranging between –8 and +8dBr.
The level used should have a known and constant relationship to the recording level and
monitor level in use. Any level can be used for reference level provided the recording
system and monitor system are related to this level.
Recording level. Dolby or Dolby Surround program
material often has wide volume range. Deciding on
optimum reference levels is a complex subject involving a
knowledge of the available headroom of the whole system
down to the release format. You should consult with our
staff on your particular application.
Monitor level. The external calibration test tone should be
related to the monitoring level. Monitor level is usually
established and verified using pink noise. Procedures for
setting monitor level are covered in the Model SDU4
manual. It is important to remember that the calibration
tone is referenced to a specific level of pink noise which, in
turn, should produce a known sound pressure in the
listening environment.
3.2 Items needed for calibration
External 1 kHz tone at standard level.
An AC voltmeter with XLR-type connector.
3.3 Calibration
1. Connect an external tone (1 kHz at studio reference level) to the L (left) input XLR
on the rear. Adjust the left input potentiometer at the front panel until the two
green leds on the left channel level indicator are on.
2. Repeat the above procedure for the Center, Right and Surround inputs.
MAIN

3-2
3. Apply the tone to the left input only. Connect a meter to the LT (left total) output
and adjust the LT output control to obtain studio reference level. Move the meter
to the LT EPL send connector and adjust the LT EPL send control for studio
reference level.
4. Repeat step 3 for the right channel by connecting the signal source to the right
input only and adjusting the RT output controls for reference level at the RT
outputs.
5. If you will be using the external processor loop, engage it by linking pins 6 and 7
on the remote control socket J507. Feed the reference tone into the L and R EPL
return connectors (together or separately) and adjust the EPL return
potentiometers to obtain reference level at the LT and RT outputs.
This completes the basic calibration of the SEU4. If the EPL loop is not to be used, remove
the link between pins 6 and 7 of J507 to restore normal operation.
Overall encoder operation and calibration can be verified by connecting the external
reference tone to each input in turn and observing the following levels on the LT and RT
outputs.
When applied to input Output should read:
at reference level: LT RT
L only ref --
C only ref –3 dB ref –3 dB (in phase)
R only -- ref
S only ref –3 dB ref –3 dB (out-of-phase)
MAIN

4-1
SECTION 4
BLOCK DIAGRAM
A3B3798 REV 4
SEU4 BLOCK DIAGRAM
2.
-3.8dB
+15V REG -15V REG
SUPPLY
POWER AND CAT.N0.385)
(TO CAT.N0.338
500mV TP201
SWITCH CONTROL
ELECTRONIC
LED GRN "EPL OUT"
CAT.NO.385. SELECTOR/POWER SUPPLY, AND THE CAT.N0.338 ARE ON THE 1. ALL ITEMS EXCEPT THE XLRS, J507, J510, AC VOLTAGE NOTES: (UNLESS OTHERWISE SPECIFIED)
DENOTES J507 PINS (D-SUBMINIATURE CONNECTOR
MOUNTED ON REAR PANEL).
3. ALL BALANCED INPUTS AND OUTPUTS ARE ON XLR CONNECTORS.
SIGNALS ON TEST POINTS (TPXXX) ARE IN PHASE WITH INPUTS AND OUTPUTS WHEN PIN 2 OF THE XLR CONNECTORS IS WIRED AS
"HIGH/HOT".
X
SELECTOR
VOLTAGE
GND 15
7
-3.8dB
LED RED "EPL IN"
14
LT
(STUDIO LEVEL)
OUTPUTS
MAIN
AMP
OUTPUT
13
500mV TP101
EPL 6
CHASSIS 8
INPUT
AC MAINS
RT
EPL RETURNS
METER 4-LED
METER 4-LED METER 4-LED
2
3
500mV
4
METER 4-LED
(-8 TO +8dBu)
INPUTS
LEVEL
STUDIO
SURROUND
LED YEL
1
RT LT
775mV
775mV
500mV L
C
R
500mV
500mV S
CAT.N0.338
RT
EPL SENDS
HYBRID OUTPUT
LT
TP301
LEVEL
EPL SEND
6dB BELOW
TP501
RT
C R
DC GROUND
(JUMPER ON I/O BOARD)
LINKED
OPEN
2J510
3
1
S
LT
AMP
DIFF
INPUT
SURR 5
DIFF AMP
INPUT
L
MAIN

A-1
APPENDIX
Dolby Surround: Getting Started
Studio Questionnaire
Technical Requirements for Dolby Surround in Recording Studios
"Phase Correctors" and Dolby Surround
MAIN

A-2
Dolby Laboratories Information
Dolby Surround: Getting Started
Console Buss Assignment
Interfacing with standard studio equipment, the professional SEU4 Encoder and SDU4
Decoder enable mixing in Dolby Surround for consumer release formats such as video,
broadcast and CD.
The SEU4 has four inputs for Left, Center, Right and Surround channels. It is not always
necessary to use the Center input. This signal is also created by central panning across
left and right groups.
On consoles specifically designed for surround mixing, use the Left, Center, Right and
Surround output busses. On stereo buss consoles, assigning two stereo output groups
designated “Left and Right,“ “Center and Surround,“ will provide the most flexible
operation. In a feature or drama production, while many sounds will remain static, it
enables the active panning of sounds, such as front to back fly-over effects.
Where a simpler mix is desirable, a Left and Right group will suffice, with a spare channel
or auxiliary send employed as the Surround send. This is particularly useful in sports or
live events where only a general ambience is usually required.
Mixing in Dolby Surround
Although no fixed rules apply, some basic mixing techniques have evolved that are
universally practiced. In features or drama production, dialogue and on-screen effects are
generally centrally positioned to provide an important visual and aural focal point.
Music and atmospheres are spread around all channels to create an enveloping ambience,
with spot effects panned to follow movement.
Similarly, in sports or live events, the main action and commentary are usually centerd,
with the audience diffused to create the atmosphere of being there.
In music-only production, a regular stereo approach provides the basis for creative
surround imaging without the constraints of matching sound to picture.
Being a system reliant on phase and signal relationships to determine imaging, it is
important to always monitor the final decoded output. For example, a typical stereo
effect like a reverb will provide a degree of center and surround information along with
the normal left and right channels. In practice, especially where time and resources are
limited, such “signal leakage” often assists in producing a quick, yet effective mix.
Audio Sources
Program material should be derived from standard multi-channel sources to enable
maximum control over sound positioning. The more independent these sources are,the
more creative the production can be.
MAIN

A-3
Stereo and Mono Compatibility
Dolby Surround is fully compatible with conventional stereo reproduction. Center
information will appear as a phantom image centered between Left and Right. Surround
information, being out-of-phase, will appear as a wide image. During mono reproduction,
the Surround signal will cancel. This rarely causes concern because such information,
especially ambience information, is usually partially present in the front channels. In the
unlikely event that information crucial to program intelligibility is only present in the
Surround channel, it may be necessary to modify the mix to ensure reasonable mono
compatibility. A monitor section on the Model SDU4 Decoder allows easy comparison
between formats.
Software Identification & Trademark Usage
All Dolby Surround masters should be identified on both packaging and report sheets.
For commercial distribution, use of the Dolby Surround logo, (or short video logo), is
encouraged on formats including video cassette, television broadcast and CD. A simple
no-cost trademark agreement is required and studios should advise their clients to contact
Dolby Laboratories directly. For regular users, a blanket agreement, covering all
productions, will keep formalities and paperwork to a minimum.
MAIN

A-4
Studio Questionnaire
Dolby Laboratories is active in the marketing of Dolby Surround and in order to maintain
our studio database, please complete and return the questionnaire located on the next
page. Our database is a valuable reference for production companies and on request,
facility addresses and contacts will be forwarded. Equipment and technical details will
however remain confidential.
Please photocopy and send or fax completed Questionnaire to either Dolby office shown.
MAIN

A-5
Questionnaire
Studio Products
Models SEU4 / SDU4
This questionnaire is for recording facilities equipped with the Dolby SEU4 Surround Encoder
and Dolby SDU4 Surround Decoder. All technical information will remain confidential.
Date _______________
Company______________________________________________________________________
Contact name ________________________ Title ____________________________________
Business address _______________________________________________________________
City____________________________________________ State/Prov ___________________
Country _________________________________________ Zip/Code ___________________
Phone ( ) ____________________________ FAX ( ) ___________________________
Model SEU4 Serial No. ____________________
Model SDU4 Serial No. ____________________
Main Equipment List:
Console _______________________________________________________________________
Monitoring - Left, Center, Right, Surround Speakers and Amps:
______________________________________________________________________________
Multitrack Machines: ___________________________________________________________
Mastering Machines: ____________________________________________________________
Other Equipment: ______________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
Please mail or fax to:
Dolby Laboratories
Studio Products Marketing
100 Potrero Avenue
San Francisco, California 94103-4813
USA
Facsimile 415-863-1373
Dolby Laboratories
Studio Products Marketing
Wootton Bassett
Wiltshire SN4 8QJ
England
Facsimile [phone]
MAIN

Dolby Laboratories Information
Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation
Signal Processing and Noise Reduction Systems
Wootton Bassett
Wiltshire SN4 8QJ England
Telephone [phone]
Facsimile 01793-842101
100 Potrero Avenue
San Francisco, California 94103-4813
Telephone [phone]
Facsimile 415-863-1373 S96/11097/11169
Technical Requirements for Dolby Surround
in Recording Studios
Using the Dolby SEU4 Encoder and SDU4 Decoder
Introduction
Dolby Surround is a format that enables the production and delivery of multi-dimensional
soundtracks for television, cable, consumer video, multimedia and other stereo media. Once
created, Dolby Surround soundtracks can be recorded, broadcast and reproduced the same as
any conventional stereo program, including compatible monaural playback. Consumers
equippedwithDolby Surround systems will experience the full measure of spatial dimension-
ality built into these programs, just as they do from thousands of Dolby encoded movies
currently available on home video media. This paper outlines the basic equipment necessary
for studios to produce soundtracks in Dolby Surround.
Surround Starts with Stereo
Many aspects of producing in Dolby Surround are the same as producing in stereo. The main
differenceisthatthemixingconsolemustideallyhaveatleastfourbussoutputstofeedaDolby
Surround encoder, and some additional speakers and amplifiers are needed to monitor the
center and surround channels via a Dolby Surround decoder.
In most cases, the finished two-channel encoded soundtrack is all that will be recorded.
However, it is sometimes desirable to record the four-channel “stems” (encoder input signals)
ontoseparatetracks when further elements are to be added later, such as with music pre-mixes
for movie soundtracks.
Necessary Equipment
1. Dolby Model SEU4 Surround Encoding Unit.
The SEU4 encodes four input signals (Left, Center, Right, Surround) into two output signals
(Lt, Rt).
2. Dolby Model SDU4 Surround Decoding Unit.
The SDU4 decodes two input signals (Lt, Rt) into four output signals (L, C, R, S) using Dolby
Pro Logic Surround decoding technology. The unit also provides switchable stereo and
monaural monitoring modes for evaluating compatibility. A ganged master fader allows all
output channels to be varied together.
MAIN

2
A note about Dolby’s products: The SEU4 and SDU4 are 1U high, 19" rack mount professional
units. Both use XLR type connectors with balanced line levels adjustable from -10 to +8 dBr
(0dBr=0.775 Vrms). Pin 2 is “hot.” For unbalanced connections, pin 1 is tied to pin 3 for proper
operation.
3. Mixing console.
Mixingwillbeperformedin four channels, so a four-buss output structure isneeded,asshown
in Figure 1. A conventional stereo console with sufficient subgrouping and auxiliary sends
may be used. Automation is not required, but may be beneficial for fine-tuning special effects.
Four channel pan pots are also desirable for certain effects, although even basic pair-wise left-
right and center-surround panning facilities may be adequate for some productions.
TheSDU4modeandlevelcontrolssimplifyconnectiondirectlytomonitoramplifiers. Figure1
shows typical signal flow.
Programmeters(withpeakand averageweighting)arerecommendedtoreadthe fourencoder
input signals and two encoder output signals.
SEU4
Encoder Mastering
Machine
Audio
Sources
SDU4
Decoder
L SRC
Amps
Speakers
S
Fig. 1 Mixing in Dolby Surround from Multitrack Elements
4. Speakers and amplifiers.
Three speakers are needed across the front to produce the left, center and right channels.
Ideally, all three will be the same model for best acoustic matching. Unfortunately, it may not
bepossibletousethe same speaker in the center due to spacerestrictions.Insuchcases,finding
one that blends well sonically is important. Using a smaller model from the same product line
as the left and right speakers is recommended. Use of a magnetically shielded speaker is
necessary whenever that speaker needs to be positioned near a video monitor.
MAIN