DOLFINOS The Cello Grip-Foot Standard Edition User manual

DOLFINOS
P L AY YOU R WAY
WITH DOLFINOS
The Cello Grip-Foot - Standard Edition
SWISS MADE

a. Plate c. Balljoint screw
d. Cylindric coupling partb. Grip sole
f. Locking screwe. Rubber sleeve
g. Allen key

1. HOW TO MOUNT
1. Insert the balljoint screw (c) with the pro-
vided allen key (g)
2. Start by putting the lip of the grip sole
(b) over the plate (a) by placing the keyway
(where the small logo is) into the notch of the
plate
3. Screw the cylindric coupling part (d) onto
the balljoint screw (c), sticking out of the
plate by using the allen key (g). Please read 2.
Special Remarks before doing this
4. Add the locking screw (f )
5. Add the rubber sleeve (e) to your endpin.
The round end of the rubber sleeve should
face down. If the rubber sleeve is too tight,
wetten the endpin to make it easier to mount
6. Fix your endpin to the Cello Grip-Foot with
the locking screw (f)
7. For the best grip of the lamella, make sure
to put the Cello Grip-Foot in front with the
logo facing up towards you.
8. To remove the Cello Grip-Foot, simply loos-
en the locking screw. The balljoint screw does
not need to be loosened for transport, it will
lose its locking function if loosened too often.
9. The smoother and cleaner the floor is, the
better the lamellar structure adheres.
Caution: with very dirty or uneven surfaces,
the floor adhesion will be reduced!
Please note that the endpin should be at least
20mm long.
The rubber sleeve is compatible with enpins
with a diameter between: 6.5 - 7.2mm. If your
endpin is between 7.3-9.8mm, you don't have
to use the rubber sleeve and use tape/mask-
ing tape instead.

3. CARE INSTRUCTIONS
1. For a rough cleaning: use a moist tooth-
brush to clean the grip sole
2 For a more thourough cleaning: Use a brush,
soap and water to remove dirt and dust. Rinse
it with water and let it dry completely before
reattaching
3. Always brush inline with the lamellas
If you always keep the Cello Grip-Foot clean,
it will prolong its lifespan.
Tipp: Use a thin thread to fasten the locking
screw to the coupling part - so you never lose
the small parts!
© 2021 DOLFINOS, All Rights Reserved.
Patent pending
2. SPECIAL REMARKS
THE BALLJOINT-SCREW:
The ballljoint screw is prepared with a
threadlocking varnish. When screwing it onto
the coupling part, this varnish prevents the
screw from loosening itself. Use the provided
allen key to adjust the tightening torque. The
friction torque in the balljoint system can be
adjusted to the desired value during initial use
(from loose to tight). Once locked, the friction
torque will remain and not loosen. You can
re-adjust the friction torque up to 3 times.
After that, the threadlocking varnish will lose
its effect. In this case, you can refresh the
threadlocking varnish yourself with Loctite
No. 243 or send your product in for a free re-
varnish. Over-tightening is not recommend-
ed. If the tightening torque is too strong, the
system may be damaged.
HIGHEST POSSIBLE INCLINATION
- Inclination towards the player: approx. 40°
- Pivot left and right: 35° to each side
[email protected]
[phone]
DISCLAIMER
DOLFINOS is not liable for any damages caused by the application and use of the product, to the instrument,
other property and person. DOLFINOS is not liable if damage is caused to the product itself, the instrument,
other property or person as a result of improper assembly and/or adjustment of the product.
The product contains small parts which can be swallowed. Keep away from children as they pose a choking
hazard!
4. ADD-ONS
1. Grip sole and rubber sleeve are wear parts.
You can order replacement parts on
www.dolfinos.com
2. If you want use the Cello
Grip-Foot on a endpin with
an unscrewable spike, you can
order a M6 coupling part