Dolmar HT-2249 D User manual

HEDGE TRIMMER
TAILLE-HAIES
HECKENBESCHNEIDEMASCHINE
TOSASIEPI
HEGGENSCHAAR
CORTASETOS
APARADOR DE SEBES
HÆKKEKLIPPER
ΨΑΛΙΔΙ ΜΠΟΡΝΤΟΥΡΑΣ
HT-2249 D
HT-2249 D
INSTRUCTION MANUAL
MANUEL D’INSTRUCTIONS
BETRIEBSANLEITUNG
ISTRUZIONI D’USO
GEBRUIKSAANWIJZING
MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUÇÕES
BRUGSANVISNING
ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ
WARNING:
To reduce the RISK of injury, user must read and understand
the instruction manual before using the Hedge Trimmer.
Manufacturer reserves the right to change specications
without notice.
Specications may differ from country to country.
Do only hand over the Hedge Trimmer together with this manual.
Avertissement:
An d’éviter les blessures, l’utilisateur doit lire et comprendre les
instructions de ce manuel avec attention avant d’utiliser le taille-haies.
Le fabricant se séserve le droit de modier les spécications sans
avertissement préalable. Les spécications peuvent varier d’un pays à
l’autre. Lorsque vous n’utiliser pas le toujours accompagner l’appareil du
manuel contenant les instructions.
WARNUNG:
Um das Risiko von Verletzungen zu verringern, sollte der Benutzer vor
verwendung des Heckenbeschneidemaschine die Bedienungsanleitung
sorgfältig durchlesen und sich mit dem Gerät vertraut machen. Der
Hersteller behält sich das Recht vor, Spezikatioen ohne Vorankündigung
zu ändern. Das Heckenbeschneidemaschine nur zusammen mit dieser
Bedienungsanleitung aushändigen.
Avvertenze:
Per ridurre il rischio di ferite, l’utilizzatore è tenuto a leggere ed a capire
questo manual d’istruzioni prima di mettere in funzione il tosasiepi. Il
produttore si riserva il diritto di modicare le caratteristiche del prodotto
senza preavviso. Le caratteristiche di questo tosasipi possono cambiare da
Paese e Paese.
Consegnare il tosasiepi solo se accompagnato da questo manuale di
istruzioni.
WAARSCHUWING:
Om het gevaar op verwondingen te vermindeen, dlent men de instructies
te lezen en te begrijpen alvorens de heggenschaar in gebruik te nemen.
De fabricant houdt het recht wijzigingen in de specicaties aan te brengen
zonder schrittelijke kennisgeving. Specicaties kunnen verschillen van land
tot land. Gebruik de heggenschaar alleen samen met deze instructies.
ADVERTENCIA:
Para reducir el riesgo de posibles lesiones, el usuario deberà leer y
entender las instrucciones de este manual antes de utilizar el cortasetos
El fabricante se reserva el derecho de cambiar las especicaciones sin
previo aviso. Las especifcaciones pueden variar de un país a otro. Ceda
únicamente el cortasetos junto con este manual.
ADVERTINDO:
Leia este manual cuidadosamente antes de pôr o Aparador de Sebes em
funcionamento e observe rigorosamente as normas de segurança.
Conserve este manual de instruções com cuidado.
ADVARSEL:
For at reducere risikoen for tilskadekomst skal brugeren læse og forstå
brugsanvisningen inden brug af hækkeklipperen.
Producenten forbeholder sig ret til at ændre specikationer uden varsel.
Specikationerne kan variere fra land til land.
Overdrag kun hækkeklipperen sammen med denne brugsanvisning.
ΠΡΟΕΙΔΟΠΟΙΗΣΗ:
Για την ελάττωση του ΚΙΝΔΥΝΟΥ του τραυματισμού, ο χρήστης πρέπει να
διαβάσει και να κατανοήσει το εγχειρίδιο οδηγιών πριν προβεί στη χρήση
του Ψαλιδιού Μπορντούρας.
Ο κατασκευαστής διατηρεί το δικαίωμα να αλλάξει τα τεχνικά
χαρακτηριστικά χωρίς προειδοποίηση.
Τα τεχνικά χαρακτηριστικά ενδέχεται να διαφέρουν ανάλογα με τη χώρα.
Να παραδίδετε πάντοτε το Ψαλίδι Μπορντούρας μαζί με αυτό το εγχειρίδιο.

2
Thank you very much for selecting the DOLMAR Hedge Trimmer. We are
pleased to e a le to offer you the DOLMAR Hedge Trimmer which is the result
of a long development program and many ears of knowledge and experience.
The Hedge Trimmer models HT-2249 D com ines the advantages of
state-of-the-art technology with ergonomic design, they are light weight, handy,
compact and represent professional equipment for a great variety of
applications.
Please read, understand and follow this booklet which refers in
detail to the various points that will demonstrate its outstanding
performance. This will assist you to safely obtain the best
possible results from you DOLM R Hedge trimmer.
SYMBOLS
It is very important to understand the following sym ols when reading this instructions manual.
WARNING/DANGER Fuel and oil mixture
Read, Understand and Follow
Instruction Manual Engine-Manual start
For idden Emergency stop
No smoking First Aid
No open flame Recycling
Protective gloves must e worn ON/START
Keep the area of operation clear of all
persons and pets OFF/STOP
Wear eye and ear protection CE - mark
English
Table of Contents Page
Sym ols.......................................................................2
Safety instructions........................................................3
Specification ................................................................6
Designation of parts.....................................................7
Fuels/Refuelling...........................................................8
Precautions efore starting ..........................................9
Starting the machine ..................................................10
Stopping the machine ................................................10
Operation of the machine........................................... 11
A
ngle change of rear handle......................................12
Maintenance instruction.............................................13
Storage ......................................................................15
Maintenance schedule...............................................15
Fault location .............................................................15

3
SAFETY INSTRUCTIONS
General Instructions
㪄㩷 THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read the Instructions
carefully for the correct handling, preparation, maintenance, starting and
stopping of the machine. Be familiar with all controls and the proper use of
the machine. (1)
㪄㩷 It is recommended only to loan the Hedge Trimmer to people who have
proven to e experienced with Hedge Trimmers.
Always hand over the instruction manual.
㪄㩷 First-time users should ask the dealer for asic instructions to familiarize
themselves with the handling of an engine powered Hedge Trimmer.
㪄㩷 Children and young persons aged under 18 years must not e allowed to
operate the Hedge Trimmer. Persons over the age of 16 years may
however use the device for the purpose of eing trained only while under the
supervision of a qualified trainer .
㪄㩷 Use the Hedge Trimmer with the utmost care and attention.
㪄㩷 Operate the Hedge Trimmer only if you are in good physical condition.
Perform all work calmly and carefully. The user has to accept lia ility for
others.
㪄㩷 Never use the Hedge Trimmer after consumption of alcohol or drugs, or if
feeling tired or ill. (2)
Intended use of the machine
㪄㩷 The Hedge Trimmer is only designed for the purpose of trimming ushes and
hedges, and must not e used for any other purpose. Do Not a use the
Trimmer.
Personal protective equipment
㪄㩷 The clothing worn should e functional and appropriate, i.e. it should e
tight-fitting ut not cause hindrance. Do not wear jewelry or loose clothing
which could ecome entangled with ushes or shru s, or the machine.
㪄㩷 In order to avoid eye, hand or foot injuries as well as to protect your hearing,
the following protective equipment and protective clothing must e used
during operation of the Hedge Trimmer.
㪄㩷 During operation of the hedge Trimmer always wear goggles or a visor to
prevent eye injuries. (3)
㪄㩷 Wear adequate noise protection equipment to avoid hearing impairment, ear
muffs, ear plugs, etc. (3)
㪄㩷 We strongly recommend that the user wears work overalls. (4)
㪄㩷 Special gloves made of thick leather are part of the prescri ed equipment and
must always e worn during operation of the Hedge Trimmer. (4)
㪄㩷 When using the Hedge Trimmer, always wear sturdy shoes with a non- slip
sole. protects against injuries and ensures a good footing. (4)
(1)
(3)
(2)
(4)

4
Starting up the Hedge Trimmer
㪄㩷 Please make sure that there are children or other people within a working
range of or 15 meters (5), also pay attention to any animals in the working
vicinity. avoid operating while people, especially children are near y.
㪄㩷 Before operating, always check that the Hedge Trimmer is safe for operation:
㪄㩷 Check the security of the throttle lever. The throttle lever should e checked
for smooth and easy action. Check for proper functioning of the throttle
lever lock. Check for clean and dry handles and test the function of the I-O
Switch. Keep handles free of oil and fuel.
Start the Hedge Trimmer only in accordance with the instructions.
Do not use any other methods for starting the engine (6)!
㪄㩷 Use the Hedge Trimmer only for applications specified.
㪄㩷 Start the Hedge Trimmer engine only after the entire assem ly is done.
Operation of the Hedge Trimmer is permitted only after all the appropriate
accessories are attached!
㪄㩷 Before starting, make sure that the cutter lade will not contact any o jects
such as ranches, stones, etc.
㪄㩷 The engine is to e stopped immediately if there are any engine pro lems.
㪄㩷 When working with the Hedge Trimmer, keep oth hands on handles always
wrap your fingers tightly around the handle, keeping the control handle
cradled etween your thum and forefinger. Keep your hand in this position
to have your machine under control at all times. Make sure your control
handle is in good condition and free of moisture, pitch, oil or grease.
Always ensure a safe, well-balanced footing
㪄㩷 Only use outdoors.
㪄㩷 Always e aware of your surroundings and stay alert for possi le hazards
that you may not hear due to the noise of the machine.
㪄㩷 Operate the Hedge Trimmer in such a manner as to avoid inhalation of the
exhaust gases. Never run the engine in enclosed rooms (risk of suffocation
and gas poisoning). Car on monoxide is an odorless gas. Always ensure
there is adequate ventilation.
㪄㩷 Stop the engine when resting and when leaving the Hedge Trimmer
unattended. Place it in a safe location to prevent danger to others, setting
fire to com usti le materials or damage to the machine.
㪄㩷 Never lay down the hot Hedge Trimmer onto dry grass or onto any
com usti le materials.
㪄㩷 To reduce fire hazard keep engine and silencer free of de ris, leaves, or
excessive lu ricant;
㪄㩷 Never operate the engine with a faulty exhaust muffler.
㪄㩷 Stop the engine during transport (7).
㪄㩷 Stop the engine or disconnect from mains efore:
㪄㩷 Cleaning or when cleaning a lockage;
㪄㩷 Checking, maintenance or working on the machine.
㪄㩷 Position the Hedge Trimmer safely during car or truck transportation to avoid
fuel leakage.
㪄㩷 When transporting the Hedge Trimmer ensure that the fuel tank is completely
empty to avoid fuel leakage.
㪄㩷 When transporting or storing the machine always fit the cutting device guard
Refuelling
㪄㩷 Stop the engine efore refuelling (7), keep well away from open flame (8) and
do not smoke.
㪄㩷 Do not attempt to refuel a hot or a running engine.
㪄㩷 Avoid skin contact with petroleum products. Do not inhale fuel vapor.
Always wear protective gloves during refuelling. Change and clean
protective clothing at regular intervals.
㪄㩷 Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the Hedge Trimmer immediately after fuel
has een spilt. Allow wet cloths to dry efore disposing in proper, covered
container to prevent spontaneous com ustion.
㪄㩷 Avoid any fuel contact with your clothing. Change your clothing immediately
if fuel has een spilled on it (danger hazard).
㪄㩷 Inspect the fuel cap at regular intervals making sure that it stays securely
fastened.
㪄㩷 Carefully tighten the locking screw of the fuel tank. Change locations to start
the engine (at least 3 meters away from the place of refuelling) (9).
㪄㩷 Never refuel in closed rooms. Fuel vapors accumulate at ground level (risk
of explosions).
㪄㩷 Only transport and store fuel in approved containers. Make sure stored fuel
is not accessi le to children.
㪄㩷 When mixing gasoline with two-stroke engine oil, use only gasoline which
contains no ethanol or methanol (types of alcohol).
This will help to prevent damage to fuel lines and other engine parts.
(5)
(6)
 Resting
 Transporting
 Refuelling
 Maintenance
 Tool Replacement
(7)
(8)
(9)
meters
(10 feet)

5
Method of operation
㪄㩷 Always use two hands to grip each handles during operation.
㪄㩷 Use the Hedge Trimmer only in good light and visi ility. During cold
seasons eware of slippery or wet areas, ice and snow (risk of slipping).
Always ensure a safe footing.
㪄㩷 Never work on unsia le surfaces or steep terrain.
㪄㩷 Never stand on a ladder and run the Hedge Trimmer.
㪄㩷 Never clim up into trees to perform cutting operation with the Hedge
Trimmer.
㪄㩷 To reduce the risk of stum ling and loss of control, do not walk ackward
while operating the machine.
㪄㩷 Always stop the engine efore cleaning or servicing the unit or replacing
parts.
㪄㩷 Do not operate the machine with a damaged or excessively worn cutting
device.
Maintenance instructions
㪄㩷 Be kind to the environment. Operate the Hedge Trimmer with as little noise
and pollution as possi le. In particular check the correct adjustment of the
car uretor.
㪄㩷 Clean the Hedge Trimmer at regular intervals and check that all screws and
nuts are securely tightened.
㪄㩷 Never service or store the Hedge Trimmer in the vicinity of open flames,
sparks, etc. (11).
㪄㩷 Always store the Hedge Trimmer in a well-ventilated locked room and with an
emptied fuel tank out of reach of children.
㪄㩷 Do not attempt to repair the machine unless you are qualified to do so;
Observe and follow all relevant accident prevention instructions issued by the trade associations safety boad and
by insurance companies.
Do not perform any modifications to the Hedge Trimmer as this will risk your safety.
The performance of maintenance or repair work y the user is limited to those activities as descri ed in this instruction manual. All other work
is to e done y Authorized Service Agent s.
Use only genuine spare parts and accessories supplied y DOLMAR authorized or factory service centers.
Use of non-approved accessories and tools means increased risk of accidents and injuries. DOLMAR will not accept any lia ility for accidents
or damage caused y the use of any non-approved accessories.
First aid
In case of an accident make sure that a well-stocked first-aid kit according to
DIN 13164, is availa le in the vicinity of the cutting operations.
Immediately replace any item taken from the first aid kit.
When asking for help, please give the following information:
㪄㩷 Place of accident
㪄㩷 What happened
㪄㩷 Num er of injured persons
㪄㩷 Extend of injuries
㪄㩷 Your name
Packaging
The DOLMAR Hedge Trimmer is delivered in a protective card oard ox to
prevent shipping damage. Card oard is a asic raw material and is therefore
consequently reusa le or suita le for recycling (waste paper recycling).
(11)
(10)

6
EC-DECLARATION OF CONFORMITY
Model; HT-2249 D
We declare under our sole responsi ility that this product is in compliance with the following standards of standardized
documents, EN774, EN55012 in accordance with Council Directives, 89/392/EEC, amended 98/37/EEC, 93/68/EEC,
89/336/EEC, amended 92/31/EEC.
Measured Sound Power: 106 dB
Guarantee Sound Power: 108 dB
These sound power levels wear measured in accordance with Council Directive, 2000/14/EC.
Conformity assessment procedure: Annex V.
CE2008
Tamiro Kishima Rainer Bergfeld
Managing Director Managing Director
Responsi le Manufacturer:
Makita Corporation.
3-11-8,Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
DOLMAR Gmbh
Jenfelder Str. 38, 22045 Ham urg, Germany
SPECIFICATION
Model HT-2249 D
Dimension (L x W x H) mm
1060 x 255 x 220
Mass (without lade cover) kg
4.7
Volume (fuel tank) L
0.4
Engine displacement cm
3
21.0
Cutting length mm
490
Maximum engine performance kw
0.6
Maximum lade speed m/s
2.1
Idling speed min
-1
3000
Clutch engagement speed min
-1
4000
Car uretor type type
WALBRO WYL
Ignition system type
Solid state ignition
Spark plug type
N K BPMR4A
Electrode gap mm
0.6 - 0.7
Idling 3000rpm m/s
2
7.5
Rear handle Racing 9300rpm m/s
2
12.9
Idling 3000rpm m/s
2
6.4
Vi ration
According to
ISO 7916
1)
Front handle Racing 9300rpm m/s
2
10.5
Sound pressure level average according to EN774
1)
dB
87.4
Sound power level according to EN774
1)
dB
106.4
Mixture ratio (fuel : DOLMAR 2-stroke engine oil) 50 : 1
Gear ratio 14 : 58
1) The data takes equally into account the idling and racing speed operating modes.

7
Ԥ
ԙ
Ԙ
ԣ
Ԣ
Ԡ
ԡ
ԟ
ԛ
Ԝ
Ԟ
ԝ
Ԛ
DESIGNATION OF PARTS
㩷㩷㩷㩷㩷㩷 HT-2249 D
DESIGNATION OF PARTS DESIGNATION OF PARTS DESIGNATION OF PARTS
1 Blade 7 Car uretor 13
Blade cover
2 Blunt extension 8 I-O Switch (ON-OFF)
3 Front handle 9 Throttle lever
4 Recoil starter 10 Rear handle
5 Fuel tank cap 11 Muffler
6 Choke lever 12 Gear ox

8
FUELS/REFUELING
Fuel and oil mixture
㪄㩷 The engine of the hedge Trimmer is a high-efficiency two-stroke engine.
It is run with a mixture of fuel and two-stroke engine oil. The engine is
designed for unleaded regular fuel with a min. -octane value of 91 ROZ.
In case no such fuel is availa le, you can use fuel with a higher octane value.
This will not damage the engine, ut may cause poor operating ehaviour.
A similar situation will arise from the use of leaded fuel.
To o tain optimum engine operation and to protect your health and the
environment, only unleaded fuel should e used!
㪄㩷 For lu ricating the engine use a two-stroke engine oil (quality grade:TSC-3),
which is added to the fuel.
The engine has een designed for use with DOLMAR two-stroke engine oil
and a mixture ratio of 50:1 only to protect the environment. In addition, a
long service life and a relia le operation with a minumum emission of exhaust
gases is guaranteed. It is a solutely essential to o serve a mixture ratio of
50:1 (DOLMAR 2-stroke engine oil), otherwise the relia le function of the
Hedge Trimmer cannot e guaranteed.
㪄㩷 The correct mixture ratio:
Gasoline : DOLMAR genuine two-stroke engine oil = 50 : 1 or
Gasoline : Other manufacturer’s two-stroke engine oil = 25 : 1
recommended
NOTE: For preparing the fuel-oil mixture, first mix the entire oil quantity with
half of the fuel required. In an approved can which meets of exceeds
all local code standards, then add the remaining fuel.
Thoroughly shake the mixture efore filling it into the Hedge Trimmer’s
tank.
It is not wise to add more engine oil than specified to ensure safe
operation. It will only result in a higher production of com ustion
residues which will pollute the environment and clog the exhaust
channel in the cylinder as well as the muffler. In addition, the fuel
consumption will rise and the performance will decrease.
Handling petroleum products
Utmost care is required when handling fuel. Fuel may contain su stances
similar to solvents. Refuel either in a well ventilated area or outdoors. Do not
inhale fuel vapors, avoid any contact of fuel or oil with your skin.
If your skin comes in contact with these su stances repeatedly and for an
extended period of time, it will desiccate.
Variouse skin diseases may result. In addition, allergic reactions are known to
occur.
Eyes can e irritated y contact with oil, fuel etc.
If oil, fuel, etc., comes into your eyes, immediately wash them with clear water.
If your eyes are still irritated, see a doctor immediately!
O serve the Safety Instructions on page 4.
Gasoline 50:1
1000 mL (1 L)
5000 mL (5 L)
10000 mL (10 L)
20 mL
100 mL
200 mL
䋫
䋫䋫
䋫

9
Refuelling
㪄㩷 The engine must e switched off.
㪄㩷 Stop the engine during refuelling, keep away from naked flames and do not
smoke.
㪄㩷 Take care not to spill either fuel or oil in order to prevent soil contamination
(enviromental protection).
Clean the Hedge Trimmer immediately after fuel has een spilt.
㪄㩷 Do not spill any fuel onto the engine. Wipe up if necessary to avoid fire.
㪄㩷 Avoid any fuel contact with your clothing. Change your clothing instantly if
fuel has een spilt on it (to prevent clothing catching fire).
㪄㩷 Inspect the fuel cap at regular intervals making sure that it can e securely
fastened and does not leak.
㪄㩷 Carefully tighten the fuel tank cap. Change location to start the engine (at
least 3 meters away from the place of refuelling.)
㪄㩷 Never refuel in enclosed rooms. Fuel vapours accumulate at ground lever.
(Risk of explosions.)
㪄㩷 Transport and store fuel only in approved containers. Make sure the fuel
stored is not accessi le to children.
㪄㩷 Thoroughly clean the area around the tank cap to prevent dirt from getting
into the fuel tank.
㪄㩷 Unscrew the plug and fill the tank with fuel. Use a gauze funnel to filter the
fuel.
㪄㩷 Tightly screw on the plug y hand only.
㪄㩷 Clean around the screw plug and the tank after refuelling.
㪄㩷 Always wipe up any spilt fuel to prevent a fire.
Storage of fuel
㪄㩷 Fuel cannot e stored for an unlimited period of time.
㪄㩷 Purchase only the quantity required for a 4 week operation period.
㪄㩷 Use approved fuel storage containers only.
PRECAUTIONS BEFORE STARTING
㪄㩷 Please make sure that there are no children or other people within a working
range of 15 meters, also pay attention to any animals in the working vicinity.
㪄㩷 Before use always check that the Hedge Trimmer is safe for operation. Check
the cutting device is not damaged, the control lever for easy action and check for
proper function of the I-O Switch.
Rotation of the cutting device during idling speed is not allowed.
Check with your dealer for adjustment if in dou t. Check for clean and dry
handles and test function of the I-O Switch.
㪄㩷 Start the Hedge Trimmer only in accordance with the instructions. Do not
use any other methods for starting the engine. (See Starting)
㪄㩷 Start the hedge Trimmer engine only after the entire assem ly is done.
Operation of the engine is only permitted after all the appropriate accessories
are attached. Otherwise there is a risk of injury.
㪄㩷 Before starting, make sure that the cutting device has no contact with o jects
such as ranches, stones, etc.
㪄㩷 Before trimming, inspect area for wires, cords, glass, or other foreigh o jects
which could come in contact with the lade.
㪄㩷 Electrical shock. Be aware of any and all electric lines and electric fences.
Check all areas for electrical lines efore cutting.
meters
(10 feet)
Diagrammatic figure

10
(1)
STARTING THE MACHINE
Move at least 3 meters away from the place of refuelling. Place the Hedge
Trimmer on a clean area of ground make sure that the cutting tool does not
come into contact with the ground or any other o jects.
Cold starting (When the engine is cold or it has een stopped for more than 5
minutes or when fuel is added to the engine.)
1. Push the I-O switch (1) to “I” position.
2. Give a gentle push on the primer pump (2) repeatedly (7 to 10 tim es) until
fuel comes into the primer pump.
3. Move the choke lever (3) to position “ ”
4. Hold the unit down firmly so you will not lose control while cranking the
engine. If not held down properly, the engine could pull you off alance or
swing the cutting lade into an o struction or your ody.
5. Pull the starter handle slowly for 10 to 15 cm, and check the location of
pressure.
6. Pull strongly when pressurization can e felt and start the engine.
7. When the engine starts, return the choke lever to “ . ” Please note that
the choke lever will return to “ ” position automatically when the throttle
lever is operated and the throttle is opened.
8. Run the engine for approximately one minute at a moderate speed efore
applying full speed.
Note:
•
If the starter handle is pulled repeatedly when the choke lever
remains at “ ” position, the engine will not start easily due to
excessive fuel intake.
•
In case of excessive fuel intake, remove the spark plug and pull
the starter handle slowly to remove excess fuel. Also, dry the
electrode section of the spark plug.
Hot staring: (Restarting immediately after the engine has stopped) When
restarting a hot engine, first try the a ove procedure: 1, 2, 4, 5, 6. If the engine
does not start, repeat a ove steps 1-8.
Note: Do not pull the starter rope to its full extent and do not allow the
starter grip to be retracted without control, ensure that it is
retracted slowly.
STOPPING THE MACHINE
1. Release the throttle lever completely.
2. Push the I-O switch (1) to “O” position, the engine rotation will ecome low
and the engine will stop.
(1)
(2)
(3)

11
OPERATION OF THE MACHINE
㪄㩷 Never operate with a loose grip.
㪄㩷 Never touch the cutting device when starting the engine and during operation.
㪄㩷 Operate the Hedge Trimmer in such a manner as to avoid inhalation of the
exhaust gases. Never run the engine in enclosed rooms (Risk of gas
poisoning). Car on monoxide is an odorless gas.
㪄㩷 All protective installations and guards supplied with the machine must e
used during operation.
㪄㩷 Never operate the engine with a faulty exhaust muffler or if it is missing.
㪄㩷 Use the Hedge Trimmer only in good light and visi ility.
㪄㩷 During the winter season eware of slippery or wet areas, ice and snow.
(Risk of slipping.) Always ensure a safe footing .
㪄㩷 Never stand on a ladder and run the Hedge Trimmer. Keep oth feet on the
ground.
㪄㩷 Never clim up the trees with the Hedge Trimmer to perform cutting
operation.
㪄㩷 Never work on unsta le surfaces.
㪄㩷 Remove sand, stone, nails, wire, etc. found within the working area. Foreign
o jects may damage the cutting lades.
㪄㩷 Before commencing cutting, the cutting lades must have reached full
working speed.
㪄㩷 Always hold the Hedge Trimmer firmly with oth hands on the handles only.
㪄㩷 Use a firm grip with thum s and fingers encircling the handles.
㪄㩷 When you release the throttle, it takes a few moments efore the cutting
lades stop.
㪄㩷 The Hedge Trimmer must not e used for cutting with fast idle. The cutting
speed cannot e adjusted with the throttle control in fast idle position.
㪄㩷 When cutting a hedge, the machine should e held so that the lades form a
15-30°angle with the cutting line.
㪄㩷 If the Hedge Trimmer is used with circular movements against the edge of the
hedge, the twigs will e thrown directly to the ground.
㪄㩷 Pay special attention when cutting hedges, which are, laid out a long a
wire-fence and have grown through the fence.
㪄㩷 The lade must not contact the fence; otherwise the lades may e
destroyed.
㪄㩷 Do not use the Hedge Trimmer continuously for a long time. It is normal to
take a reak of 10 to 20 minutes after every 50 minutes operation.
㪄㩷 Should the cutting lades hit stones or other hard o jects, immediately switch
off the engine and inspect the cutting lades for damage. Replace damaged
lades efore re-commencing work.
㪄㩷 The engine must e switched off immediately in case of any engine
pro lems.
㪄㩷 Operate the Hedge Trim m er with as little noise and contam ination as possi le.
In particular check the correct setting of the car uretor and the fuel/oil ratio.
㪄㩷 Do Not attempt to remove jammed cut material when lades are running.
Put unit down, turn it off, and remove necessary cuttings.

12
ANGLE CHANGE OF REAR HANDLE
To permit vertical operation of the unit, the angle of the rear handle is designed to e changed.
How to change the angle
㪄㩷 Return the throttle lever, and rotate the rear handle, push the rotation lever.
㪄㩷 Rotate the rear handle to the right or left y 90 degrees.
㪄㩷 After rotation, release the lock pin. To secure the rear handle, hold the
rotation lock pin gently y the finger.
NOTE: For safety, the stopper works to catch the throttle lever during rotation
of the handle. Rotate the rear handle after complete rotation y 90
degrees.
Vertical operation
㪄㩷 In rotating the rear handle to the right, hold the rear handle y the right hand,
and the front handle y the left hand. Perform cutting in a circle.
㪄㩷 In rotating the rear handle to the left, hold the front handle y the right hand,
and the rear handle y the left hand. Perform cutting in a circle.
Rotation leve
r

13
MAINTENANCE INSTRUCTIONS
㪄㩷 Turn off the engine and remove the spark plug connector when replacing or sharpening cutting tools, also when cleaning the cutter or cutting
device or carrying out any maintenance.
㪄㩷 Never straighten or weld a damaged cutting lade.
㪄㩷 Inspect the cutting lades with the engine switched off at short, regular intervals for damage.
㪄㩷 (Detection of hairline cracks y means of tapping-noise test.) Beware the teeth are sharp.
㪄㩷 Clean the Hedge Trimmer at regular intervals and check that all screw and nuts are well tightened.
㪄㩷 Never service or store the Hedge Trimmer in the vicinity of naked flames to avoid fires.
㪄㩷 Always wear leather gloves when handling or sharpening the lades, as they are sharp.
Blade sharpening
If the edges are rounded and do not cut well any more, grind off only the
shaded portions. Do not grind the contact surfaces (sliding surfaces) of the top
and ottom edges.
㪄㩷 Before grinding, e sure to secure the lade firmly and switch off the engine
and remove the spark plug cap.
㪄㩷 Wear gloves, protective glasses, etc.
㪄㩷 An edge ground too much at a time or ground many times will lose its
hardened layer. It ecomes rounded and dull very quickly in use.
Checking and adjusting the idling speed
The cutting lade should not when the control lever is fully released.
㪄㩷 Idle speed should e set to 3,000 min
-1
.
㪄㩷 If necessary, correct it y means of the idle screw (the cutting lade must not
run when the engine is on idle).
 Clockwise : for faster rate of revolution
 Counter-clockwise : for slower rate of revolution
Check that there is sufficient difference etween idling and clutch
engagement speed to ensure that the cutting tool is at a standstill while the
engine is idling. (If necessary, reduce idling speed.) If the tool still
continues to run under the idling conditions, consult your nearest authorized
service agent.
 The clutch should engage at minimum 3,750 min
-1
.
 Check the functioning of the I-O Switch, the lock-off lever, the control lever,
and the lock utton.
Cleaning of air cleaner - Every 8 hours Daily)
㪄㩷 Remove the air cleaner cover.
㪄㩷 Push the choke lever up (arrow), to prevent dirt particles from entering the
car uretor.
㪄㩷 Take out the sponge element, wash it in lukewarm water and dry it
completely.
㪄㩷 After cleaning, put ack the sponge element and the air cleaner cover.
NOTE: If there is excessive dust or dirt adhering to the air cleaner, clean it
every day. A clogged air cleaner may make it difficult or impossi le to
start the engine or increase the engine rotation speed which could
cause damage.
Disk grinder
10 q 10 q
Edge cross
section
Holding the disk grinder at
a 45°angle, grind the edge
off to the dotted line to
shar
p
en the rounded ti
p
.

14
Checking the spark plug - Every 8 hours Daily)
㪄㩷 Only use the supplied universal wrench to remove or to install the spark plug.
㪄㩷 The gap etween the two electrodes of the spark plug should e 0.6 to
0.7mm. If the gap is too wide or too narrow, adjust it. If the spark plug is
clogged with car on or fouled, clean it thoroughly or replace it. Use an exact
replacement.
Supply of grease and lubricant
㪄㩷 Supply grease from the grease nipple every 20 operating hours. (Shell
Alvania No.2 or equivalent)
NOTE: Be sure to o serve the specified time and amount of grease supply.
If the grease supply is not mad e at the specified interval or if the
amount of grease supplied is not sufficient, the machine may fall into a
trou le ecause of lack of grease.
Suction head in the fuel tank
㪄㩷 The felt filter (1) of the suction head is used to filter the fuel required y the
car uretor.
㪄㩷 A periodical visual inspection of the felt filter is to e conducted.
㪄㩷 For that purpose, open the tank cap, use a wire hook and pull out the suction
head through the tank opening.
Filters found to have hardened, een polluted or clogged up are to e
replaced.
㪄㩷 Insufficient fuel supply can result in the admissi le maximum speed eing
exceeded. It is therefore important to replace the felt filter at least quarterly
to ensure satisfactory fuel supply to the car uretor.
Cleaning of muffler exhaust port
㪄㩷 Check of muffler exhaust port (2) regularly.
㪄㩷 If it is clogged y car on deposits, carefully scratch the deposits out with a
suita le tool.
Do not allow car on to fall into engine ports.
Any maintenance or adjustment work that is not included and descri ed in this manual is to e performed y Authorized Service Agent only.
Daily checkup and maintenance
To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should e performed at regular
intervals.
㪄㩷 Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter lade screws.
㪄㩷 Before operation, always check for clogging of the cooling air passage and the cylinder fins. Clean them if necessary.
㪄㩷 Perform the following work daily after use:
 Clean the Hedge Trimmer externally and inspect for damage.
 Clean the air filter. When working under extremely dusty conditions, clean the filter several times a day.
 Check the lades for damage and make sure they are firmly mounted.
Grease nipple
Grease will come out from here.
(1)
(2)

15
STORAGE
㪄㩷 When keeping the machine in storage for a long time, drain fuel from the fuel
tank and car uretor, as follows: Drain all fuel from the fuel tank.
㪄㩷 Remove the spark plug and add a few drops of oil into the spark plug hole.
Then, pull the starter gently to confirm that oil film covers the engine inside
and tighten the spark plug.
㪄㩷 Clear dirt or dust from the cutter lade and outside of engine, wipe them with
a oil-immersed cloth and keep the machine at a place as dry as possi le.
MAINTENANCE SCHEDULE
General Engine assem ly,
screws and nuts Visual inspection for damage and tightness Check for general condition and security
After each refuelling Throttle lever
Safety lock key
I-O switch
Functional check
Functional check
Functional check
Daily Air filter
Cooling air duct
Cutting tool
Idling speed
To e cleaned
To e cleaned
Check for damage and sharpness
Inspection (cutting tool must not move)
Every 20 hours Gear case Supply of grease
Weekly Spark plug
Muffler Inspection, replace if necessary Check and if necessary clean the opening
Quarterly Suction head
Fuel tank To e replaced To e cleaned
Shuting down
procedure
Fuel tank
Car uretor Empty fuel tank Operate until engine runs out of fuel
FAULT LOCATION
Fault System Observation Cause
Ignition system Ignition spark is present Faulty fuel supply or compression system, mechanical defect Engine not starting or
under difficulties No ignition spark I-O switch operated, wiring fault or short circuit, spark plug or
connector defective, ignition module faulty
Fuel supply Fuel tank filled Incorrect choke position, car uretor defective, suction head (gas
line filter) dirty, fuel supply line ent or interrupted
Inside of engine Cylinder ottom gasket defective, crankshaft seals damaged,
cylinder or piston rings defective
Compression
Outside of engine Improper sealing of spark plug
Mechanical
fault Starter not engaging Broken starter spring, roken parts inside of the engine
Warm start pro lems Tank filled
Ignition spark existing Car uretor contaminated, have it cleaned
Incorrect idling adjustment, suction head or car uretor
contaminated
Engine starts ut dies
immediately Fuel supply Tank filled
Fuel tank vent defective, fuel supply line interrupted, ca le or
I-O switch faulty
Insufficient
performance Several
systems may
simultaneously
e affected
Engine idling Air filter contaminated, car uretor contaminated, muffler clogged,
exhaust duct in the cylinder clogged

㩷
16
Vous venez d’acheter un Taille-Haies DOLMAR, fruit d’importants pro rammes
de développement et de nombreuses annétudes et d’expérience-et nous vous
en remercions.
Les modéles HT-2249 D lé ers, prafiques et compact s, allient les avanta es
d’une technolo ic de pointe à une conception er onomique, et sont des outils
de professionnels pour de norebreuses applications.
Lire attentivement ce manuel et suivre les instructions données.
Il décrit en détail les divers points démontrant les exc eptionnelles
performances du souffleur. Ceci v ous permettra d’obtenir les
meilleurs résultats de ce Taille-Haies.
SYMBOLES
Lors de la lecture de ce manuel, prêtez une attention particuliêre aux symboles ci-après:
Attention! Dan er! Mélan e de carburant et d'huile
Lire ct suiver le manuel de fonctionnenent Démarra e manuel de la machine
Interdit Arrêt d'ur ence
Interdit de fumer Premier secours
Interdiction d’utilisation de produits
inflammables Recycla e
Port de ants de protection obli amire On/Démarra e
Zone de fonctionnement interdite aux
humains et aux animanx Off/Arrêt
Port de lunettes de protection er
cache-creilles obli atoire Lo o de la CE
Table des matières Page
Symboles................................................................... 16
Consi nes de sécurité ............................................... 17
Données techniques.................................................. 20
Liste des piéces......................................................... 21
Carburant/Ravitaillement ........................................... 22
Precautions a observer avant le demarra e............... 23
Demarra e de la machine ........................................ 24
A
rret de la machine.................................................... 24
Fonctionnement de la machine.................................. 25
Chan ement de l’an le de la poi nee arriere............. 26
Instructions de maintenance................................. 27-28
Remisa e .................................................................. 29
Pro ramme d’en tretien .............................................. 29
Localisation des défauts ............................................ 29
French

㩷
17
CONSIGNES DE SECURITE
Généralités
㪄㩷 CET APPAREIL PEUT PROVOQUER DES BLESSURES GRAVES.
Veuillez lire attentivement le manuel d’instruction afin de manipuler, entretenir,
mettre en route et arretêr correctement l’appareil. Chaque utilisateur est
prié de se familiariser avec la totalite des commandes et des modes
d’utilisation appropriés du taille-haies. (1)
㪄㩷 Il est recommandé de prêter le taille-haies uniquement aux personnes
expérimentées dans la manipulation du taille-haies. Remettez leur toujours
le manuel d’instructions.
㪄㩷 Les premiers utilisateurs devraient demander des instructions de base au
concessionnaire afin de se familiariser à la manipulation d’un taille-haies
matorisé.
㪄㩷 Les enfants et les jeunes ens de moins de 18 ans ne devraient pas être
autorisés à faire fonctionner le taille-haies. Les personnes de plus de 16
ans peuvent cependant utiliser la machine pour s’entraîner à la seule
condition qu’ils soient sous la surveillance d’une professeur qualifié.
㪄㩷 Utilisez le taille-haies avec un soin et une vi ilance extrêmes.
㪄㩷 Utilisez le taille-haies uniquement si vous êtes en bonne condition physique.
Effectuez tous les travaux avec calme et soin. L’utilisateur doit accepter la
responsabilité des autres personnes.
㪄㩷 N’utilisez jamais le taille-haies après absorption d’alcool ou de médicaments
ou si vous vous sentez fati ué ou malade. (2)
㩷
Fonction de la machine
㪄㩷 Le taille-haies est conçu uniquement dans le but de couper des buissons et
des haies et ne doit pas être utilisé pour tout autre tâche.
Prière de ne pas malmener le taille-haies.
㩷
Equipement de protection personnel
㪄㩷 Le volet de protection de l’appareil de coupe doit être monté lors du transport
de la machine vers un autre lieu.
㪄㩷 La tenue doit être fonctionnelle et appropriée, c’ est - à - dire qu’elle doit être
serrée sans toutefois entraver les mouvements. Ne portez pas de bijoux ou
d’habits susceptibles de s’entrelacer dans les buissons, les broussailles ou la
machine.
㪄㩷 Utilisez l’équipement de protection et les habits de protection suivants lors de
l’utilisation du taille-haies afin d’éviter des blessures au niveau de la tête, des
mains ou des pieds ainsi qu’afin de proté er votre ouïe.
㪄㩷 Portez toujours des lunettes ou une visière pour éviter les blessures au
niveau des yeux lors de l’utilisation du taille-haies. (3)
㪄㩷 Portez un équipement de protection sonore approprié pour éviter les
détériorations auditives, des boules Quies, des bouchons d’oreilles, etc. (3)
㪄㩷 Nous recommandons fortement aux utilisateurs de porter une combinaison
de travail. (4)
㪄㩷 Des ants spéciaux en cuir épais font partie de l’équipement prescrit et
doivent toujours être portés lors de l’utilisation du taille-haies. (4)
㪄㩷 Lors de l’utilisation du taille-haies, portez toujours des chaussures solides
avec une semelle antidérapante. Elles vous éviteront des blessures et vous
arantiront une bonne stabilité. (4)
(1)
(3)
(2)
(4)

㩷
18
Mise en marche du taille-haies
– S’assurez qu’aucun enfant ou aucune autre personnene se trouve à moins
de 15 mètres (5) de la zone d’utilisation du taille-haies’assurez é alement
qu’il n’y a aucun animal dans les para es. S’assurez é alement qu’il n’y a
aucun animal dans les para es. Evitez de mettre l’appareil en marche s’il y
a du monde près de vous, notamment des enfants.
– Avant l’utilisation, toujours vérifier les points suivants afin d’assurer la sécurité:
– Vérifier que la manette des az est bien fixée. S’assurer que la manette des
az est facile à manoeuvrer et que son mouvement est ré ulier. S’assurer
que le verrou de la manette des az fonctionne correctement. S’assurer
que les poi nées sont propres et sèches et vérifier le fonctionnement du
bouton “arrêt”. Veiller à ce qu’il n’y ait ni huile ni carburant sur les poi nées.
– Avant de mettre la machine en marche, assurez-vous que toutes les
instructions sont bien respectées.
N’utilisez pas d’autres méthodes de mise en marche de l’appareil (6).
– N’utilisez la machine et les outils fournis que pour les applications spécifiés.
– Ne mettez la machine en marche que lorsque tous les accessoires ont été
mis en place. L’appareil ne fonctionne que lorsque tous les accessoires
appropriés y sont fixés.
– Avant de démarrer l’appareil, s’assurer que la lame n’est pas en contact avec
d’autres objets, tels que brancha es, pierres, etc.
– En cas de problème du moteur, l’arrêter immédiatement.
– Lors de l’utilisation du taille-haies, toujours bien refermer les doi ts sur la
poi née, de façon à avoir la poi née de commande entre le pouce et l’index.
Laisser la main à cette position pour avoir constamment le plein contrôle de
l’outil. Veiller à ce que la poi née de commande soit en bon état et libre de
toute humidité, pente, huile ou raisse.
Veiller à a oir toujours une bonne prise des pieds.
– Utiliser exclusivement à l’extérieur.
– Restez toujours conscient de ce qui se passe autour de vous, et toujours
vi ilant devant toute sorte de dan er pouvant survenir et que vous n’aurez
pas entendu venir du fait du bruit que fait l’appareil en fonctionnement.
– Pendant le fonctionnement de l’appareil, évitez toute inhalation de az
d’échappement. N’utilisez jamais l’appareil dans des endroits clôs (en
raison des risques d’étouffement et d’empoisonnement par les az
d’échappement). N’oubliez pas que le monoxyde de carbone est un az
sans odeur. N’utilisez l’appareil que dans un endroit bien aéré.
– Coupez le moteur lorsque vous n’utilisez pas l’appareil, et mettez-le en lieu
sûr pour éviter de blesser l’entoura e, de mettre le feu aux matériaux
combustibles, ou d’endomma er la machine.
– Ne posez jamais la machine chaude sur de l’herbe sèche ou des matériaux
combustibles.
– Afin d’éviter tout risque d’incendie, s’assurez qu’aucuns débris, feuilles ou
lubrifiant excessif ne soit resté attaché au moteur ou au silencieux.
– Ne faites jamais fonctionner la machine si le silencieux pose problème.
– Coupez l’alimentation du moteur pendant le transport (7).
– Coupez le moteur ou débranchez-le avant:
 de nettoyer l’appareil ou de nettoyer un bourra e;
 toute vérification, entretien ou travail sur l’appareil.
– Pendant le transport, évitez toute fuite de carburant.
– Pendant le transport, assurez-vous que le réservoir de carburant est
totalement vide.
– Enclenchez systèmatiquement le dispositif de sûreté lors du transport ou de
l’entreposa e de l’appareil.
Plein de carburant
– Coupez le moteur (7), assurez-vous qu’il n’y a aucune flamme à proximité (8).
– Ne faites jamais le plein d’un moteur chaud ou en marche.
– Ne fumez pas. Evitez tout contact avec la peau et les produits dérivés du
pétrole. N’inhalez pas les vapeurs d’essence. Portez toujours des ants
de protection. Chan ez et nettoyez ré ulièrement les ants de protection.
– Veillez à ne pas renverser de carburants ou d’huile, pour éviter de
contaminer le sol (protection de l’environnement). En cas de fuite de
carburant, même lé ère, nettoyez immédiatement l’appareil. Faites toujours
sécher les chiffons avant de les jeter dans un conteneur approprié et couvert,
pour éviter tout risque de combustion spontanée.
– Evitez tout contact du carburant avec les vêtements. Si nécessaire,
chan ez immédiaternent de vêtement.
– Vérifiez ré ulièrement le bon fonctionnement du bouchon du réservoir.
Assurez-vous que le bouchon du réservoir est bien serré, et ne mettez le
moteur en marche qu’a un minimum de 3 m de l’endroit ou vous avez fait le
plein (9).
– Ne faites jamais le plein de carburant dansdes pièces fermées : les vapeurs
s’accumulent au niveau du sol (risque d’explosion).
– Ne transportez et ne stockez du carburant que dans des conteneurs
appropriés. Veillez à ce que les enfants n’y aient pas accès.
– Lorsque vous mélan ez de l’essence et de l’huile pour moteur à deux temps,
utilisez uniquement de l’essence ne contenant ni éthanol, ni méthanol pour
ne pas endomma er les pièces du moteur.
(6)
 Repos
 Transport
 Plein de carburant
 Maintenance
 Remplacement d’outils
(7)
(8)
(5)
15 mètres
(50 pieds)
(9)
3 meters
(10 feet)
3 mètres
(10 pieds)

㩷
19
Méthode d’utilisation
㪄㩷 Manipulez toujours le conpe-haies avec vos deux mains que vous lissez
fermement dans chacune des poi nées.
㪄㩷 N’utiliser le taille-haies qu’avec un éclaira e et une visibilité suffisante. En
hiver, prendre arde aux endroits lissants ou mouillés, à la lace et à la
nei e (risque de lisser). Veiller à avoir toujours une bonne prise des pieds.
㪄㩷 Ne jamais travailler sur une surface instable ou sur un terrain en pente.
㪄㩷 Ne jamais se tenir sur une échelle en manipulant le taille-haies.
㪄㩷 Ne jamais rimper dans les arbres pour procéder à des travaux de coupe
avec le taille-haies.
㪄㩷 Pour éviter de tomber et de perdre le contrôle de l’appareil, ne reculez jamais
pendant son fonctionnernent.
㪄㩷 Coupez toujours le motenr avant de nettoyer l’appareil on de remplacer
certaines de ces pièces.
㪄㩷 Ne faites jamais fonctionner le coupe-haies avec une lame endomma ée ou
trop usée.
Maintenance
㪄㩷 Respectez l’environnement ; vérifiez notamment le bon ré la e du
carburateur pour polluer aussi peu que possible l’atmosphère.
㪄㩷 Vérifiez ré ulièrement le taille-haies, et assurez - vous que ses vis et écrous
sont bien fixés.
㪄㩷 Pendant toutes les opérations de maintenance ou de stocka e, évitez
soi neusement la présence de flammes, d’étincelles ou autres (11).
㪄㩷 Stockez toujours l’appareil dans une pièce fermée à clé et bien aérée.
Avant de le stocker, videz soi neusement son réservoir.
㪄㩷 Ne cherchez pas à réparer l’appareil à moins d’être qualifié pour le faire.
Observer les consignes de prévention des accidents publiées par les associations professionnelles concernées et
par les sociétés d’assurance. Ne pas modifier la taille- aies car cela pourrait porter atteinte à la sécurité.
N’effectuez ancune opération de maintenance ou de réparation qui ne soit pas prévue par ce manuel. Toutes les autres opérations doivent
être effectuées par des représentants antorisés. N’utilisezque des pièces et des accessoires d’ori ine, fournis par DOLMAR.
L’utillsation d’outils et d’accessoir es non a réés an rnente les risques d’accident. DOLMAR décline toute responsabilité en cas d’accident ou
de domma e provoqué par l’utilisation d’accessoires ou d’outils non a réés.
Premiers secours
Pour être paré en cas d’accident, prévoir une trousse de pre m iers secours bien
fournie, et conforme à la norme DIN 13164, à proximité des opérations de
coupe. Remplacer immédiatement tout article pris dans la trousse de premiers
secours.
En cas d’accident, appeiez les services de secours et fournissez-leur les
informations suivantes:
– Lieu de l’accident
– Circonstances de l’accident
– Nombre de personnes blessées
– Type de blessures
– Vos coordonnées
Emballage
Le Taille - Haies DOLMAR est livré dans un carton qui le protè e contre les
domma es pendant le transport. Le carton est une matière première de vase
et il peut être réutilisé ou recycié (recycla e des vieux papiers).
(11)
(10)

㩷
20
DECLARATION DE CONFORMITE CE
Modèle : HT-2249 D
Nous prenons la responsabilité pour déclarer que le présent produit est conforme aux normes suivantes énoncées aux documents EN774,
EN55012 conformément aux Drectives du Conseil, 89/392/CEE, 98/37/CEE, 93/68/CEE, 89/336/CEE modifiées et 92/31/CEE modifiée.
Niveau sonore mesuré : 106 dB
Niveau sonore aranti : 108 dB
Niveaux sonores mesurés conformément à la Directive du Conseil, 2000/14/CE.
Procédure d'évaluation de conformité 㧦 Annexe V
CE2008
Tamiro Kishima Rainer Ber feld
Directeur Général Directeur Général
Producteur responsable:
Makita Corporation.
3-11-8,Sumiyoshi-cho, Anjo, Aichi, JAPAN
Représentant autorisé en Europe:
DOLMAR Gmbh
Jenfelder S tr. 38, 22045 Hambur , Germany
CARACTÉRISTIQUES TECHNIQUES
Modèle
HT-2249
Dimensions : lon ueur x lar eur x hauteur mm
1060 x 255 x 220
Masse (sans protection et lame de coupe) k
4.7
Volume (réservoir de carburant) L
0.4
Cylindrée du moteur cm
3
21.0
Lon ueur de coupe mm
490
Puissance maximale du moteur kw
0.6
Vitesse d’arbre maximale (correspondante) m/s
2.1
Vitesse de marche à vide min
-1
3000
Vitesse d’embraya e min
-1
4000
Carburateur type
WALBRO WYL
Systéme d’alluma e type
Type Allumage élect onique
Bou ie d’alluma e type
NGK BPMR4A
Ecartement entre les électrodes mm
0.6 - 0.7
Au ralenti 3000rpm m/s
2
7.5
prise
arrièr En marche 9300rpm m/s
2
12.9
Au ralenti 3000rpm m/s
2
6.4
Vibration
selon
ISO 7916
1)
prise
avant En marche 9300rpm m/s
2
10.5
Niveau moyen de pression acoustique selon EN774
1)
dB
87.4
Niveau moyen de puissance acoustique selon EN774
1)
dB
106.4
Rapport du mélan e (carburant:huile pour moteur 2 temps
50 : 1
Rapport d’en rena es
14 : 58
1) Les caractéristiques prennent en compte tous les modes de fonctionnement: Vitesse de marche á vide, emballement et papillon des az ouvert á
fond