DOM FAMILY 4109 User manual

BABY WALKER
Read all instructions before assembly and use of the walker.
Keep instructions for future use
1532 S Washington Ave Piscataway TWP NJ
08854
www.dreamonme.com
DRAWINGS IN THIS MANUAL ARE FOR ILLUSTRATION PURPOSES
ONLY, ACTUAL PRODUCT MAY VARY. MANUFACTURER RESERVES
THE RIGHT TO CHANGE ANY SPECIFICATION OR FEATURES WITHOUT
PRIOR NOTICE.
Email: [e-mail]

AWARNING
1. ) Never leave the child unattended ;
2. ) Prevent access to stairs, steps and uneven surface ;
3. ) Read the instructions carefully before use and keep them
for future reference.
The child may be hurt if you do not follow these instructions ;
4. ) The child will be able to reach further and move faster than
before when in the baby walking frame ;
5. ) Guard all fires, heating and cooking appliances ;
6. ) Remove hot liquids, electrical flexes and other potential
hazards from reach ;
7. ) Prevent collision with glass in doors, windows and furniture ;
8. ) Do not use the baby walking frame if any components
are broken or missing ;
9. ) This baby walking frame should be used only for short
periods of time(e.g.2O min);
10. )This baby walking frame is intended to be used by children
who can sit unaided , approximately from 6 months. It is not
intended for children weighing about 26 pounds or 12 kgs;
11. )Do not use replacement parts other than those approved
by the manufacturer or distributor;
12. )Should you have any questions about your baby walker
or experience any difficulties , please contact the retailer
from which you purchased the product. Your local retailer
is in the best position to promptly address any requirements.
13. )Executive standard: ASTM F977,16 CFR 1216.
14. )Never leave child unattended.Always keep child in view
while in walker.
15. )Use only on flat surfaces free of objects that could cause
the walker to tip over.
16. )To avoid burns, keep the child away from hot liquids,ranges,
radiators, space heaters, fireplaces,etc.
17. )Each walker shall be labeled with a separate stairs warning
visible to the consumer when placing the child in the walker.
18. )The product shall be assembled by an adult
nn
Care and Maintenance:
1. ) Never force mechanisms or moving parts. If you are not sure what to
do refer to the instructions.
2. ) Clean plastic and metal parts with a damp cloth or a light detergent.
Do not use solvents,ammonia or petrol.
3. ) Regularly check unit to ensure no parts are loose or broken.
4. ) Clean the rubber pad regularly to maintain stopping performance.
A
WARNING
STAIR HAZARD
Avoid serious injury or death.
Block stairs/steps securely
before using walker.
Parking brake use does not
totally prevent walker
movement.Always keep child
in view when in the walker,
even when using the parking
brakes.

4. FUNCTION:
1.HEIGHT ADJUSTOR
To adjust walker to desired position (there are 3 positions available)
put one hand on the top of walker, and turn the red button on
the height adjustment mechanism beneath the top table by 90
degrees with other hand. Then push up the button to adjust height
position. When you release the red button, it will return to original
position. The mechanism is locked automatically (See Fig1&2).
2.GLOBAL FRONT WHEELS: Front wheels can rotate(See Fig3).
3.SAFETY RUBBER PADS: Safety rubber pads for avoiding
children falling down the stairs or tipping over in walker(See Fig4).
4.STRAIGHT WHEELS: The straight wheels will automatically brake
when baby walker is moving backwards too fast(See Fig5).
EE!
1. PARTS IDENTIFICATION
NON-MUSICAL TOY TRAY
HEIGH ADJUSTMENT
MECHANISM
BOTTOM TRAY
RUBBER PADS
FABRIC SEAT
UPPER TRAY
STRAIGHT WHEELS
TUBE
GLOBAL WHEELS
2. CARTON CONTENTS:
Please check if all those parts are included when you open the carton. If there are any
missing parts please contact your local retailer
Q J& .
WALKER FRAME X1 PC FABRIC SEAT X1 PC TOY TRAY X1 PC PLASTIC BACKREST
X1PC
O1
STRAIGHT WHEELS X2PCS TOYX1PC RUBBER PADS X6PCS GLOBAL WHEELS X2PCS
E3

3. ASSEMBLY INSTRUCTION
1) ASSEMBLY OF THE PARTS UNDER THE BOTTOM RIM:
See Fig 1: Insert those 6 rubber pads into their positions.
See Fig 2: Insert 2 global wheels into the holes under front bottom,
as the left and right wheels are different,make sure that the left and
right wheels are properly installed as per above Fig 1, DO NOT
install the left and the right wheel up side down.
See Fig 3: Insert 2 straight wheels into the holes under rear bottom.
Please make sure that all parts are fixed well as picture shown on Fig4.
2) FRAME ASSEMBLY:
As picture shown on Fig 5 & Fig 6, please follow the direction of the
arrow. Completely open frame when you hear the sound “click”.
3) Backrest assembly:
See Fig 7: Insert 2pins on the both side of backrest as the arrow
shown. See Fig 8, press down the backrest as the arrow shown.
E0
______________________________________ /
Assembly of the fabric seat:
First, insert the pins in the front of seat into the holes on the upper
tray referring to Fig 9. Then pull out the buckles at the back of seat
through the holes on the upper tray according to Fig 10. The fabric
seat is fixed completely as shown on Fig 11.
TOY TRAY ASSEMBLY &DISASSEMBLY:
See Fig 12, Following the derection of of the
arrow,insert the toy into hole of the tray,the
assembly is finished.
See Fig 13/14, Putting the toy tray on the upper
tray and pushing down, when hearing a “click”, the
assembly is finished, See Fig 15. Following the
direction of arrow and pressing the button of the
musical toy tray under the upper tray, the
disassembly is completed.
BE!

Enter our monthly giveaway!
Simply scan the QRcode to register.
Chat with us!
For any questions or concerns or feedback.
1532, S. Washington Avenue
Piscataway, NJ 08854
E-mail: [email protected]
www.dreamonme.com
Follow us on
to get your nursery featured on our social media.
@dreamonmeinc @dreamonmeinc