DOM FAMILY 414 User manual

Model: #414
Dream On Me Inc. 1532 South Washington Ave, Piscataway TWP, NJ 08854
Tel [phone] Fax [phone]
MADE IN FO SHAN, GUANG DONG, CHINA
Thank you for choosing Dream On Me and congratulations on joining The DOM
Family, a family that has been transforming lives for 30 years! We appreciate your
feedback and wish you the very best in the coming years with your new addition. If
you have any questions or concerns please don’t hesitate to reach out and a trusted
DOM representative will assist you. Thank you again for entrusting us to supply you
with the safest, functional and affordable baby products and accessories. Feel free
to follow us on Facebook and Instagram for further opportunities and offers.
1) Never force mechanisms or moving parts. If you are not sure about what to
do, please refer to the instructions.
2) Clean plastic and metal parts with a damp cloth or a light detergent. Clean
safety rubbers regularly to maintain stopping performance. Do not use
solvents, ammonia or petrol.
3) Regularly check unit to ensure that no parts are loose or broken.
4) Clean the rubber pads regularly to maintain stopping performance.
• Prevent access to stairs, steps and uneven surfaces.
• The child will be able to reach further and move faster than before
when in the baby walker.
• Guard all fires, heating, and cooking appliances.
• Remove hot liquids, electrical flexes, and other potential hazards
from reach.
• Prevent collision with glass in doors, windows and furniture.
• Do not use the baby walker if any components are broken or
missing.
• This baby walker should be used only for short periods of time
(e.g. 20min).
• Do not use replacement parts other than those approved and
provided by Dream On Me.
• Never leave child unattended. Always keep child in view while in
walker.
• Use only on flat surfaces, free of objects that could cause the
walker to tip over.
• To avoid burns, keep the child away from hot liquids, ranges,
radiators, space heaters, fireplaces, etc.
• Each walker is labeled with a separate stairs warning visible to
the consumer when placing the child in the walker.
• The product must be assembled by an adult.
Read the instructions carefully before use and keep them for future
reference. The child may get hurt if you do not follow these instructions.
•The product uses 2 AA 1. 5V batteries.
•Do not reverse the polarity of the batteries.
•It is prohibited to charge non-rechargeable battery.
•It is only available to charge the battery under adult' s attendance.
•Please take out the battery from the toy before charging.
•Do not mix use different type of batteries or new and old batteries
together.
•Ensure the proper and right polarity onto the toy.
•Please take out the worn-out batteries from the toy.
•Do not shortcut the polarities of the battery.
•It is prohibited to let child play with the battery as toy so as to
avoid danger.
As shown in Fig 18, remove the battery cover by unscrewing it.
Then, insert new batteries into the battery box. (Note, pay attention
to their poles "+" and "-" ). Now, screw the screws back in.
Press the music key for music.
WARNING!
•Never leave the child unattended. Always keep child in view while in walker.
•Intended for children who can sit unaided, approximately 6 months of age. Not
intended for children who can walk by themselves or weight more than 25 lbs or
hight more than 27.6 inches.
Avoid serious injury or death. Block stairs/steps securely
before using walker, even when using parking brake.
Fig 18
Fig 17
Fig 16
Fig 15
Turn the folding knob as shown in Fig 15, and push the walker body forward as
shown in Fig 16. Then, fold backward as shown in Fig 17.

Please check to make sure that all of the following parts listed are included in the box when
opened. If there are any missing parts, please contact Dream On Me before using the product.
.
Rear wheel knob
NOTE!
The knob as shown in Fig 6 is used
for the walk-behind. Please refer to
the detailed instructions of function.
4. Instruction for the rear wheel knob
(For walk-behind model only)
Insert the rear wheel knob into the mounting hole of the rear wheel until it is locked tightly. Turn
the knob tight or loose to control the walk speed. The rear wheel knob needs to be removed when
the product is switched back into the walker model. Turn the knob counter-clockwise to loosen
and pull off.
•As shown in the Fig 1, place the walker right side up and
insert the wheel rod into the hole, pressing it in place.
•Insert the rear wheels into the mounting slots, pressing it in
place.
•Insert the anti-sliding bars into the mounting slots, pressing it in
place.
•Power switch.
•Function keys: touch the key to switch games,
children songs, little pianist, etc.
•The music key: Press them to light up and play
music.
1. Function instroduction
As shown in Fig 5, lift up and
pull back the backrest until it
"clicks" into position.
Turn the walker body over. Lift and unfold the walker body by pulling up the handle. Rotate it to
the position as shown in Fig 4 until you hear a "click", which means that the walker has locked
into place. Please check and make sure that the walker locks into position before use.
Insert the handle bar into the mounting holes of the
walker body in place as shown in Fig 2 until it is
locked. (Note: The direction of the armrest should
be in line with Fig 2.)
As shown in Fig 8, change the length of the
ribbon in front of the cushion to adjust its height.
•Switch to walk-behind function:
As shown in Fig 9, wiggle the lock
buckle as shown by the arrow
and lift it up outward to remove
the seat ring. Next, remove the
cushion to allow the walker to be
used in it's walk-behind function
by having your baby can walk
holding the handle bar.
•Switch to walker function:
As shown in Fig 11, insert the
seat ring into its locking holes on
the frame and press it down as
the arrow shown in Fig 12 until
they "click" into position and are
locked tightly.
Fig 13
Front wheel
Handle bar 1 pc
Anti-sliding bar 6 pcs
Rear wheel
Walker body
Fig 12Fig 11
Fig 10Fig 9
Fig 8
Fig 14
Fig 7
Fig 6
Fig 5
Fig 4
Fig 3
Fig 2
Fig 1
Handle bar
Walker body 1 pc Front wheel 2 pcs Rear wheel 2 pcs
Rear wheel knob 2 pcs
Anti-sliding bar
Assembling the handle bar