Dometic WDCVL Manual

This product is designed solely for use in
recreational vehicles or other mobile equipment.
©2013 Dometic Corporation
LaGrange, IN 46761
WASHER / DRYER COMBO VENTLESS
MODEL WDCVL(XX)
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
SERVICE CENTER &
DEALERLOCATIONS
Please Visit:
www.eDometic.com
INSTALLATION & OPERATING
INSTALLATION & OPERATING
INSTRUCTIONS
INSTRUCTIONS
Read these instructions carefully. These
instructions MUST stay with this product.
This product is designed solely for use in
recreational vehicles or other mobile equipment.
REVISION E
16138100A 13262 10/16
@2016 Dometic Corporation
Elkhart, IN 46514

2
TABLE OF CONTENTS
INTRODUCTION....................................................................................................................................................................2
DOCUMENT SYMBOLS ........................................................................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS................................................................................................................................3
A. Recognize Safety Information ...................................................................................................................................3
B. Understand Signal Words..........................................................................................................................................3
C. State of California Proposition 65 Warnings ..............................................................................................................3
D. General Safety Messages .........................................................................................................................................3
E. Electric and Installation Precautions..........................................................................................................................3
F. Operation Precautions...............................................................................................................................................4
G. Maintenance, Service, and Disposal Precautions .....................................................................................................5
INSTALLATION REQUIREMENTS ........................................................................................................................................6
A. Tools and Parts..........................................................................................................................................................6
B. Location Requirements..............................................................................................................................................6
C. Installation Clearances ..............................................................................................................................................6
D. Electrical Requirements.............................................................................................................................................7
E. Appliance Dimensions ...............................................................................................................................................7
F. Unpacking the Appliance ...........................................................................................................................................7
G. Packing Material Disposal .........................................................................................................................................7
H. Remove Transport Bolts ...........................................................................................................................................7
I. Select the Location ....................................................................................................................................................8
J. Connect the Inlet Hose..............................................................................................................................................8
K. Drain System Options................................................................................................................................................8
L. Fastening and Leveling the Appliance.......................................................................................................................9
OPERATING INSTRUCTIONS............................................................................................................................................ 10
A. Laundering Recommendations................................................................................................................................10
B. View of Control Panel and Functions ...................................................................................................................... 11
C. Option Buttons.........................................................................................................................................................13
D. Reference Symbols Displayed on the Panel ...........................................................................................................14
E. Preparing for First Use ............................................................................................................................................14
F. Laundering Fabrics..................................................................................................................................................14
CARE AND CLEANING........................................................................................................................................................16
A. Cleaning the Appliance Cabinet ..............................................................................................................................16
B. Cleaning the Internal Drum......................................................................................................................................16
C. Cleaning the Detergent Dispenser and Grooves.....................................................................................................16
D. Cleaning the Inlet Filter............................................................................................................................................16
E. Cleaning the Tap Filter............................................................................................................................................. 16
F. Washing the Filter in the Appliance .........................................................................................................................17
G. Removing Foreign Objects ......................................................................................................................................17
H. Winterizing/Storing when temperatures drop below 32° F (0° C):...........................................................................17
DISPLAY DIAGNOSTIC CODES .........................................................................................................................................19
APPENDIX ...........................................................................................................................................................................20
A. Fabric Care Label References.................................................................................................................................20
B. Technical Specifications ..........................................................................................................................................20
INTRODUCTION
These instructions apply to the washer/dryer combo (hereinafter referred to as the “appliance”). The appliance is designed
and intended for installation and use in a recreational vehicle or other mobile applications.
These instructions will ensure a properly installed and properly functioning appliance.
Dometic Corporation reserves the right to modify appliance appearances and specifications without notice.
DOCUMENT SYMBOLS
Indicates additional information that is not re-
lated to physical injury. Indicates step-by-step instructions.

3
IMPORTANT SAFETY INSTRUCTIONS
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.
A. Recognize Safety Information
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
B. Understand Signal Words
A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.
indicates a hazardous situation that,
if NOT avoided, could result in death or serious in-
jury.
indicates a hazardous situation that,
if NOT avoided, could result in minor or moderate
injury.
is used to address practices NOT
related to physical injury.
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries .
C. State of California Proposition 65
Warnings
The California Safe Drinking Water
and Toxic Enforcement Act requires the Governor
of California to publish a list of substances known
to the State of California to cause cancer, birth
defects, or other reproductive harm, and requires
business to warn of potential exposure to such sub-
stances.
This product contains a chemical known to the Sate
of California to cause cancer, birth defects, or other
reproductive harm. This appliance can cause low-
level exposure to some of the substances listed,
including benzene, formaldehyde, and carbon mon-
oxide.
D. General Safety Messages
Failure to obey the following instruc-
tions could result in death or serious injury due to
electrical shock, fire, or explosion.
This appliance MUST be installed and serviced by a
qualified service technician.
Read and understand these instructions before install-
ing, using, servicing, or performing maintenance on
this appliance.
The safety precautions provided in this manual cannot
cover all possible conditions that may occur. Com-
mon sense and caution MUST be exercised when
installing, maintaining, and operating this appliance.
The installation MUST comply with all applicable local
and national codes including the latest editions of the
following standards:
U.S.A.
●ANSI/NFPA70, National Electric Code (NEC)
●ANSI/NFPA1192, Recreational Vehicles Code
Canada
●CSA C22.1, Parts I & II, Canadian Electrical Code
●CSA Z240 RV Series, Recreational Vehicles
E. Electric and Installation Precautions
Failure to obey the following instruc-
tions could result in death or serious injury due to
electrical shock, fire, or explosion.
●This appliance weighs 175 lbs (79 kg). Do NOTat-
tempt to move or reposition this appliance unless
you are fully capable of doing so without injury.
●The appliance should NOT be installed in any
room with above-average humidity. It MUST NOT
be stored in any room with explosive or caustic
gases.
●Ensure that the water and electrical hookup(s)
is/are connected by a qualified technician in ac-
cordance with the manufacturer's instructions
(refer to the "Installation Instructions" on pages
6-9) and local safety regulations.
●Do NOT modify the power cord provided with the
appliance for any reason. Have a proper outlet
installed by a qualified electrician.
●Route and secure the power cord to protect it from
damage. Do NOT use extension cords.
●This is a 120V/60Hz appliance. Make sure the
cord is connected to a 120V/60Hz power source.
●Ensure this appliance is only used on a dedi-
cated 120V electrical circuit that has 15 amps of
overcurrent protection. Use time-delay fuses with
this appliance when it is connected to a circuit
protected by fuses.

4
●This appliance MUST be grounded. In the event
of a malfunction or breakdown, grounding will
reduce the risk of electrical shock by providing a
path of least resistance for the electric current.
This appliance is equipped with a cord that has an
equipment-grounding conductor and a grounding
plug. The plug MUSTbe plugged into an appropri-
ate outlet that is properly installed and grounded
in accordance with all local and national codes
and ordinances.
●This appliance is for indoor use only.
●Packing materials may cause suffocation. Keep
all packing materials away from children.
●All packaging and transportation bolts MUST be
removed, otherwise serious damage may occur
while washing or drying clothes.
Risk of corrosion or freeze damage.
●Do NOT install or store this appliance where it will
be exposed to temperatures below 32°F (0°C) or
moisture.
F. Operation Precautions
Failure to obey the following instruc-
tions could result in death or serious injury due to
electrical shock, fire, explosion, suffocation, poison-
ing, or allergic reaction.
●Read and understand this entire manual before
using the appliance.
●Contact your local distributor, service agent, or
the manufacturer if you have any questions about
the proper operation and service of the appliance
●This appliance is intended for RV use only.
●This appliance is NOT intended for use by per-
sons (including children) with reduced physical,
sensory, or mental capabilities, unless the user
is operating the appliance under the supervision
of a legal parent or guardian capable of safely
operating the appliance. When children become
mature enough to operate the appliance, it is the
legal responsibility of the parent or guardian to
ensure that they are instructed in and capable of
the safe use of the appliance.
●Do NOT use any toxic solvents, such as alco-
hol, as a detergent. Only approved detergent
pods or select HE liquid detergents suitable
for front-loading washing machines should
be used.
●Do NOT launder fabrics that have been cleaned,
washed, soaked, or spotted with gasoline, dry
cleaning solvents, or any other flammable or
explosive substances as they give off vapors that
could ignite or explode.
IMPORTANT SAFETY INSTRUCTIONS
●Do NOT add gasoline, dry cleaning solvents, or
any other flammable or explosive substances to
the appliance as they give off vapors that could
ignite or explode.
●Do NOT place any item with traces of any flam-
mable substance, such as vegetable oil, cooking
oil, or any other petroleum-based oil or distillate
into the appliance. Even after laundering, these
substances may smoke or ignite.
●Under certain conditions, hydrogen gas may be
produced in a hot-water system that has NOT
been used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If the hot-water system
has NOT been used for two weeks, open all hot-
water faucets and allow water to flow for several
minutes before using the appliance. This will re-
lease any accumulated hydrogen gas. The gas is
flammable. Do NOT smoke or use an open flame
during this time.
●Do NOT allow children to play on, in, or with the
appliance. Close supervision of children is neces-
sary when the appliance is in use.
●Children or pets may climb into the appliance
between uses. Check the appliance before each
use.
●Do NOT operate the laundering machine if any
guards, panels and/or fasteners, except transport
bolts, have been removed.
●Do NOT operate the appliance if any parts are
missing or broken.
Failure to obey the following instruc-
tions could result in personal injury.
●Be careful of scalding water or steam when the
appliance drains hot wash water.
●Ensure that the water inside the drum has drained
before opening the door. Do NOT open the door
if there is any water visible.
●The glass door may become very hot during
operation.
●Caution should be used when opening the appli-
ance door after the drying cycle.
●ALWAYS turn the appliance off before opening
the door. Do NOT reach into the appliance if the
tub is in motion.
●Do NOT place any fiberglass materials, such
as curtains or window coverings that may use
fiberglass, in the appliance. Small particles may
remain and stick to fabrics in subsequent washes
causing skin irritation.

5
IMPORTANT SAFETY INSTRUCTIONS
Failure to obey the following instruc-
tions could result in premature wear, water damage,
or other damage to the appliance or its surroundings.
●Before operating this appliance, all packing mate-
rials and transport bolts MUST be removed. Oth-
erwise, the appliance may be seriously damaged
during attempted use (refer to page 7 "Remove
Transport Bolts").
●Prior to initial use, run the appliance through the
cotton and hot water modes without any articles
of fabric inside. This is required to flush out any
debris that may be in the hoses or drum.
●Only fabrics suitable for machine laundering and/
or drying should be placed in the appliance.
●Do NOT dry anything containing foam rubber or
similarly textured rubber-like materials.
●Do NOT wash carpets.
●Any sharp or metal objects such as coins, nails,
screws, pebbles, jewelry, hair broaches, or curl-
ers may cause appliance or fabric damage if put
into the appliance.
●Ensure all pockets on clothing are emptied before
laundering.
●Do NOT use fabric softener sheets in the appli-
ance. Use liquid fabric softeners only.
●Disconnect the power and shut off the water sup-
ply when the appliance will NOT be in use.
●NEVER refill the water by hand during laundering.
●ALWAYS empty the machine when the cycle has
completed.
●ALWAYS follow the fabric care instructions rec-
ommended by the fabric manufacturer.
●Do NOT use standard powdered detergents with
the appliance. Use caution and limit the quantity of
bleach and other stain removers when pretreating
stained fabric.
●Do NOT use the controls in a manner inconsistent
with the instructions in this manual.
●Check the fill hose connection on a regular basis
to ensure there is no leakage.
●Do NOT climb, lean, or sit on the appliance.
●Do NOT close the door with excessive force. If it
is difficult to close the door, ensure that the load
is evenly distributed and does NOT exceed the
appliance's capacity (see page 11).
G. Maintenance, Service, and Disposal
Precautions
Failure to obey the following instruc-
tions could result in death or serious injury due to
electrical shock, fire, or suffocation.
●ALWAYS unplug the appliance before perform-
ing any maintenance. Disconnect the power by
grasping the plug, NOT the cord.
●NEVER disconnect the power cord with wet
hands.
●This appliance MUST be repaired by an autho-
rized service center using only authentic ac-
cessories and service parts, unless specifically
recommended in the user maintenance instruc-
tions or in published user repair instructions that
you understand and have the skill to implement.
●Do NOT attempt to repair or replace any part of
the appliance unless specifically recommended in
the user maintenance instructions or in published
user repair instructions that you understand and
have the skill to implement.
●If the power cord is damaged, have it replaced
by a qualified service professional.
Failure to obey the following instruc-
tions could result in structural damage to the appliance
or water damage to its surroundings.
●The interior of the appliance should be cleaned
periodically by a qualified service professional.
●The transport bolts MUST be reinstalled by a
qualified technician prior to moving the appliance.
●The accumulated water should be drained from
the appliance prior to moving or servicing the
appliance.
●Handle the appliance carefully. NEVER grasp a
protruding part while lifting the appliance. The
appliance door cannot be used as a handle dur-
ing transport.
●If you decide to dispose your appliance, please
observe local waste disposal regulations. Cut off
the power cord so that the appliance cannot be
connected to a power source. Remove the door
so that animals and small children cannot get
trapped inside the appliance.

6
INSTALLATION REQUIREMENTS
Risk of serious injury or death due to
electrical shock.
The appliance MUST be properly grounded. Ground-
ing reduces the risk of electrical shock if the appliance
housing becomes energized.
Risk of serious injury or death due
to fire.
The appliance MUST be connected to a dedicated
15 amp circuit separate from other electrical appli-
ances. The overcurrent protection MUST be rated
at 15 amps.
The life of the appliance may be sig-
nificantly shortened if operated on an incline.
The maximum incline angle upon which the appliance
rests MUST be no more than two degrees.
A. Tools and Parts
Gather the required tools and parts before attempting
installation. The parts included with the appliance are
in the drum. Other items required for installation are
the responsibility of the installer.
●Items included:
●(2) Water hoses
●(3) Brackets
●(4) Transport bolts
●(1) Template
●Items NOT included:
●1/4" nut driver
●3/8" open end wrench
●7/16" socket with ratchet
●3/8" socket with ratchet
●Adjustable 9/16" open-end wrench
●Channel-lock adjustable pliers
●Carpenter’s level
●Flexible screw driver extension
●Cable tie
●Screws
●Siphon break (if required)
B. Location Requirements
Selecting the proper location for your appliance im-
proves performance, minimizes noise and possible
appliance movement. Your appliance can be in-
stalled under a custom counter, closet, or recessed
area. See “Drain System Options” (Page 8). Proper
installation is the qualified installer's responsibility.
●Required Items:
●A water heater set to deliver 120°F (49°C)
water to the appliance.
●A grounded electrical outlet located within 3
ft. (1 m) of where the power cord is attached
to the back of the appliance. See “Electrical
Requirements”.
●Hot and cold water faucets located within 3
ft. (1 m) of the hot and cold water fill valves,
and water pressure of 7.3–145 psi (0.05MPa–
1MPa).
●A level floor with a maximum slope of 2° (2.5
cm) under the entire appliance.
●A sturdy and solid floor to support the appli-
ance's total weight (water and load) of 200 lbs.
Installing the appliance on soft floor surfaces,
such as carpets or surfaces with foam backing,
is NOT recommended.
●Do NOT operate or store your appliance in
temperatures below 32°F (0°C). Some water
can remain in the appliance and cause dam-
age in low temperatures.
C. Installation Clearances
●The location MUST be large enough to allow the
appliance door to be fully opened.
●Additional spacing should be considered for ease
of installation and servicing. The door opens more
than 90°, and it is NOT reversible (Fig. 1).
●Additional clearances might be required for wall,
door, and floor moldings.
●Spacing of 1 inch (2.5 cm) on all sides of the ap-
pliance is required (Fig. 2).

7
FIG. 1
FIG. 2
The dimensions shown are for minimal spacing using a
custom under-counter installation.
F. Unpacking the Appliance
●After unpacking, check the appliance for any
damage that may have occurred during transport.
●Instructions for unpacking the appliance from
the carton are located on the top of the transport
carton.
●Ensure that all included items are undamaged. If
any part of the appliance incurred damage during
transport, file a damage claim with the shipping
company.
G. Packing Material Disposal
Risk of serious injury or death due to
suffocation. The packing materials of this machine
may be dangerous to children. Please dispose of
them properly, and keep out of reach of children.
●Do NOT throw the packing materials away with
the other daily trash. Dispose of these materials
according to the relevant local regulations.
H. Remove Transport Bolts
Before using this appliance, transport bolts
MUST be removed from the backside of this
machine. Complete the following steps to re-
move the bolts:
D. Electrical Requirements
Risk of serious injury or death due
to electrical shock, fire, or explosion if the following
instructions are NOT followed.
●A 120V/60Hz, AC only, 15 or 20 amp fused elec-
trical supply is required. A time-delay fuse or a
circuit breaker serving only this appliance MUST
be provided.
●This appliance is equipped with a power supply
cord that has a 3-prong grounding plug. Do NOT
remove the ground plug.
●Do NOT use an adapter.
●Do NOT use an extension cord.
●To minimize possible shock hazard, the power
cord MUST be plugged into a 3-prong, grounding
type outlet that is grounded in accordance with
local codes and ordinances. If a 3-prong outlet is
NOT available, it is the responsibility and obliga-
tion of the user to have the properly grounded
outlet installed by a qualified electrician.
●If local codes permit the use of a separate ground
wire, it is necessary that a qualified electrician
determine that the ground path is adequate.
●DO NOT ground the appliance to a gas hose.
●Consult a qualified electrician if you are unsure
whether the appliance is properly grounded.
●DO NOT use a fuse in the neutral or ground
circuit.
E. Appliance Dimensions
INSTALLATION REQUIREMENTS
FIG. 3
FIG. 1

8
INSTALLATION INSTRUCTIONS
Loosen all bolts with a wrench and then remove
them and their sleeves.
2. Cover the holes with transport hole plugs.
3. Keep the transport bolts for future use.
4. Make sure the small triangle foam is removed
with the bottom one together. If not, lay the unit
down with side surface, then remove the small
foam from the unit bottom manually.
Risk of damage to appliance or sur-
roundings. Review and follow all safety and installa-
tion instructions during installation.
I. Select the Location
Before installing the appliance, select a location
that adheres to the following criteria:
A rigid, dry, and level surface removed from di-
rect sunlight.
2. Proper ventilation
3. Room temperature must be above freezing
(32°F or 0°C).
4. Isolated from heat sources
NOTE: Ensure the appliance does not rest on its
power cord. It is recommended the appliance is
not installed on any soft floor surfaces.
J. Connect the Inlet Hose
Connect the inlet hose as indicated in the
figure. Connect the hoses to the hot water taps
as indicated.
Do not over-tighten the hoses. If there is any
leakage after connection, confirm the hose end
has a rubber “O” ring and repeat the steps to
connect the inlet hose.
2. Connect the fitting to the tap and fasten it clock-
wise.
FIG. 6
3. Connect the opposite end of the hose to the
inlet valve on the backside of the appliance.
FIG. 5
K. Drain System Options
●The standpipe drain system may be installed in the
wall (Fig. 6) or floor (Fig. 7).The drain requires a min-
imum inner-diameter standpipe of 2 inches (5 cm).
●The minimum carry away capacity of the drain can
be no less than 17 gal (64 L) per minute. The top
of the standpipe MUST be between at least 23.6
inches (60 cm) and 39.4 inches (100 cm) above
the bottom of the appliance.
●The laundry tub drain system (Fig. 8) requires a
minimum 20 gal (76 L) capacity. The top of the
laundry tub MUST be a minimum of 23.6 inches
above the floor but no more than 39.4 inches.
FIG. 8
FIG. 4
6
60
(100 cm
)
”
2
3.6
”
Max 39
.4”
FIG. 7

9
INSTALLATION INSTRUCTIONS
●The floor drain system (Fig. 9) requires an air
gap and siphon break that MUST be purchased
separately. The siphon break MUST be a mini-
mum of 23.6 inches (60 cm) from the bottom of
the appliance. Additional hoses may be needed.
L. Fastening and Leveling the Appliance
If the template is not placed flush with the back
wall of the installation area, measure its location
to ensure proper alignment of the appliance.
2. Align the appliance with the template and se-
cure the brackets with screws on the exposed
bracket sides. Next, remove the template
and finish securing the brackets. Note: The
slot openings must be facing toward the front.
3. Ensure the floor’s surface is protected against
damage. Slide the appliance and align the rear
legs to the rear bracket slot openings. Ensure
that the legs are within ¼ inch from the back of
the slot.
4. Level the machine using the front legs.
a. When positioning the laundering machine,
ensure the front legs are in the shortest po-
sition that will allow room for the foot to fit
inside the bracket. If not, adjust the legs to
their shortest position by hand and tighten
the nuts with a wrench.
b. After positioning the appliance, ensure that it
is stable by pressing on the four corners of
the appliance. If the appliance shifts, the leg
underneath must be adjusted.
c. To ensure the positioning of the appliance,
loosen the lock nut with a wrench and turn
the leg with your hand until it contacts the
floor.
d. Press the leg with one hand and fasten the
nut tightly to the cabinet with a wrench.
e. Press the four corners again to ensure the
legs have been properly locked and adjust-
ed. Repeat step 4b if the appliance is still
unstable.
f. Use a level to ensure the appliance is
not on an incline. Repeat steps 4b–d un-
til the machine is completely leveled.
5. Align the bracket on the front right side in line
with the leg, and slide the bracket over the leg
until it touches the foot. The slot opening must
be facing the back of the appliance. Fasten
the bracket with screws through the two out-
board holes. The inboard holes are left empty.
TEMPLATE TOP VIEW
BACK OF APPLIANCE
FRONT
FRONT
FIG. 9
FIG. 10
FIG. 12
FIG. 11
FRONT OF APPLIANCE
FIG. 13

10
FIG. 14
OPERATING INSTRUCTIONS
A. Laundering Recommendations
●Review, understand, and follow all Safety and Op-
eration instructions when operating the appliance.
●Thoroughly review all operating instructions be-
fore using the appliance. Any incline of the RV
contributes to the angle of the appliance. Do NOT
operate the appliance if the tilt of the appliance
exceeds 2°.
●Dometic is NOT responsible for damage to any
improperly laundered fabrics, including but NOT
limited to color fading, color transfer, wrinkling,
and shrinkage.
●If you are laundering clothes for the first time,
check their color fastness. Use a white towel
damp with liquid detergent to rub a portion of the
fabric and check if the towel is stained by the fab-
ric. Wash clothes that lose their color separately.
●Wash temperature-sensitive clothes as directed
by the label to avoid premature fading.
●NEVER store clothes in the appliance. Otherwise
they may mold or stain. Remember to dry clothes
immediately after laundering to prevent molding.
Clothes may change color or fade if the label
instructions are NOT observed.
●Clothes that may NOT be washed:
●Clothes that may be damaged if immersed
in water.
●Ties, waistcoats, leather garments, and outer
garments, which may shrink if immersed in
water.
●DO NOT wash clothes marked for dry clean-
ing only.
●Costumes, embossed, or resin clothes may be
damaged when immersed in water. Along with
cotton and wool materials, the clothes that are
most easily damaged are wrinkle-style silk and
any fabric lined with fur.
●DO NOT wash clothes without material labels
or laundering requirements.
●Some clothes such as fleece and corduroy should
be turned inside-out before laundering to reduce
fiber loss. ALWAYS check the care label before
laundering.
●DO NOT wash water-proof materials such as ski
suits or raincoats.
Failure to obey the following instruc-
tions could result in death or serious injury due to
fire or explosion. NEVER wash clothes stained with
chemicals such as gasoline, petroleum, benzene,
paint thinner, alcohol, cooking oils, etc. NEVER add
such chemicals to the appliance.
●Regarding detergents:
●Use the recommended Dometic Detergent
Pods inside the drum with clothes. For liquid
detergent, use HE front-loading specifically
formulated detergent. Pre-detergent, liquid
detergent and fabric softener go in the dis-
penser drawer. Use only 1–2 tablespoons of
liquid detergent.
●Take into consideration the type and amount of
fabric to be washed and the laundering method
before choosing your detergent; otherwise,
excessive suds may be generated.
●Use bleach sparingly as it can damage fabric
permanently.
●DO NOT use powder detergents as it will cre-
ate sudsing.
●Laundering effectiveness depends on water
softness as well as using detergent properly.
●Keep detergents and additives in a dry place
out of reach from children.
●Additional notes and guidelines for clothes:
●Clothes washed together should share similar
characteristics. Care labels define whether a
shirt is cotton, blended fiber, synthetic fiber,
silk, or wool.
●White and colorful clothes MUST be washed
and dried separately. All new colorful fabrics
should be washed separately.
●Delicate articles MUST be washed separately.
New pure wool fabrics, curtains, and silk fab-
rics should be washed on the delicate setting.
●Clothes should be sorted prior to laundering.
Remove the hooks from any curtain before
laundering.
●Decorations on fabric may damage the
laundering machine. Fabric with buttons or
embroideries should be turned inside-out be-
fore laundering. ALWAYS read the care label
before laundering.

11
OPERATING INSTRUCTIONS
TABLE 1
●Zippers should be zipped closed and buttons
or hooks should be secured.
●NOTE: Any type of garment with hook or wire
inserts should be washed within an enclosed
mesh bag. It is suggested to wash bras in a
pillow slip to prevent the steel wire from pro-
truding from the bra and potentially damaging
the appliance. Other delicate fabric, such
as stockings or handkerchiefs, should also
be washed within an enclosed mesh bag.
●Laundering large or heavy articles such as
towels, jackets, or bedding may cause a load
imbalance. Adding additional articles of fabric
should help to offset the imbalance. Do NOT
exceed the appliance loading capacities.
●Delicate articles should be washed separately.
Increase the rinsing time of any delicate ar-
ticles to ensure there is no residual detergent.
●Fabrics with tough stains should be pretreated
before placement in the appliance.
●Do NOT overload the appliance. Different fabrics
have different load restrictions. Refer to the table be-
low for the maximum load capacity of the appliance:
Max Wash Load
Capacity
Max Dry Load
Capacity
Fiber Types
Cotton 15 lbs (6.8 kg) 7.5 lbs (3.4 kg)
Synthetic 7.5 lbs (3.4 kg) 7.5 lbs (3.4 kg)
Wool 5.5 lbs (2.5 kg) 5.5 lbs (2.5 kg)
B. View of Control Panel and Functions
Refer to FIG. 17 for the selection options listed
below.
1. On/Off: Press once to turn the appliance on,
press again will turn off the appliance.
2. Start/Pause: Press to start a wash or dry cycle.
If the appliance is running, pressing the button
once will temporarily pause the laundering pro-
cess. Press it again to restart the cycle. If the
cycle is not restarted within 10 minutes, it will be
cancelled.
3. Select cycles and options: Not all options are
available with all cycles. Cycles and options can
be changed any time before the Start/Pause
button is pressed. The Dry function is available
in options with the symbol .
4. To cancel a cycle:
●Press and hold the On/Off button until the
unit shuts off. Press the power button once to
turn the unit back on. After turning on the unit,
wait 3-5 seconds for an audible click indicat-
ing the appliance door has unlocked. A new
wash/dry cycle may be selected at this time.
NOTE: Turning the unit off while it is running
will not save any of the information of the cur-
rent cycle.
5. To add a garment:
●Press and hold the Start/Pause button until
an audible beep is heard. Wait 3-5 seconds
and an audible click will indicate the appli-
ance door has unlocked. The user may add
additional garments to the load. To resume
the current cycle, press the Start/Pause but-
ton again. NOTE: A new cycle cannot be se-
lected when following the steps in this option.
6. To drain the appliance manually:
a. Press Power for approximately 3 seconds.
b. Select spin.
c. Press the Start/Pause button.
d. When the spin is complete, the door will un-
lock.
7. Wash cycles:
NOTE: The screen displays a preset run
time, but the run time is dependent on the
appliance’s sensors. The length of operation
is based on fabric dryness and temperature.
All times displayed for a given cycle are ap-
proximate.
●Normal/Cotton: The default setting on Normal/
Cotton wash cycle runs for approximately 54
minutes. It comes with the option of Wash+Dry
,Extra Rinse, and Time Save. When dry is
turned on, the cycle runs for approximately 2
hours and 17 minutes.
FIG. 15
FIG. 16

12
OPERATING INSTRUCTIONS
FIG. 17
Notes: 1. The control panel line chart is for reference only. 2. The control panel could be changed without written notice. 3. The program cycle with icon indicates that the Dry cycle option is available as an add on.

13
OPERATING INSTRUCTIONS
●Heavy Duty: The Heavy Duty wash is for heavy
material and has the option of Wash+Dry, .
●Bulky/Large: The Bulky/Large wash is for
materials that are bulky with the cycle running
approximately 1 hour and 30 minutes.
●Duvet: The Duvet wash is designed for wash-
ing duvet.
●Sport: This cycle helps wash heavily soiled
fabric with higher prewash and main wash
temperatures. Its has the option of Wash+Dry.
●Spin Only: This is a separate spin cycle. All
water will be drained before this cycle begins.
●Rinse & Spin: Select this cycle to rinse and
spin a load separately from a regular cycle.
This can be helpful in preventing fresh stains
from setting into fabrics.
●Tub Clean: (Self-Cleaning Function): NOTE:
Do NOT use this setting to wash fabrics. Do
NOT add detergent or fabric softener when us-
ing this cycle. This cycle is specially designed
to clean the appliance’s drum and tubes. It
uses an extremely high temperature to steril-
ize and maintain the proper functioning of the
appliance. Adding a small amount of oxidizing
bleach to the cycle will increase the cleaning
effect. Use this cycle on a monthly basis to
keep the inside of the appliance clean.
●Quick: This cycle is ideal for quickly launder-
ing small loads. It comes with the option of
Wash+Dry.
●Delicate: This cycle is ideal for silk fabrics and
similar delicate materials.
●Sanitize: This cycle is specially designed to
sanitize clothes with high water temperatures.
It does NOT drain water, it needs to be com-
bine with another wash function to complete
the wash cycle.
●Wool: This cycle is ideal for wool fabrics
labeled “Machine Wash”. Select the proper
temperature as indicated by the fabric’s care
label. NOTE: Proper detergent MUST be used
when laundering wool fabrics.
●Under Wear: This cycle is ideal for laundering
under garments. It has an additional rise cycle.
●Refresh: During this cycle, hot air is pumped
into the drum to remove wrinkles and restore
freshness to fabrics. It can be used to dry fab-
rics collectively weighing less than 1.1 lbs (0.5
kg), such as a damp shirt or a pair of shorts.
●Dry: This is for drying only. The dry time can
be selected based on load size up to load limit
specified on Table 1 on page 11.
●My Cycle: Press "Spin" for 3 seconds to load
the cycle and options you are currently using to
the "my cycle" program. Selecting this program
in the future will load the cycle for quick use.
C. Option Buttons
Note: To select the desired option, press the button
until setting shows on the screen.
●Time Save: This function can decrease the
wash time.
●Delay: The delay function can be set between
0-24 hours. The start light will illuminate to
indicate the delay time. It will start the cycle
after the selected delay time has elapsed.
To Active:
I. Select program cycle.
II. Press delay button to choose time.
III. Press Start/Pause to active Delay option.
To cancel:
I. Press the Delay button until the display
shows 0H. It should be pressed before
activating the program.
II. If the program as already started, press
the On/Off button.
●Temp.: Press this button until desired setting
is lit. Available options will vary based on wash
cycle selected.
●Spin Speed: The appliance drum spins at up to
1200 rpm. This reduces drying time and saves
energy. Press the “Spin Speed” button until
the indicator light for the desired setting is lit.
Delicate fabrics require a slower spin speed.
●Soil level: This option is divided into three
levels. Choosing the right soil level increases
the appliance’s efficiency.
●Dry Level: Press this button to select the
cycle’s temperature based on load size. There
are three levels available.
●Child Lock: Press the “Soil” and “Dry level”
buttons at the same time to lock/unlock the
control panel.

14
OPERATING INSTRUCTIONS
D. Reference Symbols Displayed on the
Panel
E. Preparing for First Use
●Before laundering clothes for the first time, the
laundering machine MUST run through the com-
plete cycle of procedures without fabric as follows:
1. Connect to a power source and water.
2. Put liquid detergent into the dispenser and
close it.
3. Press the “Power” button.
4. Press the “Start/Pause” button.
●The drawer is separated as follows:
I: Pre-detergent
II: Main detergent
: Laundering additive, such as fabric soft-
ener
●Putting detergent into the appliance:
1. When using a Dometic or any other pod de-
tergent, place the pod in the drum with fab-
ric, or if using liquid detergent:
●Pull out the detergent dispenser.
●Pour liquid pre-detergent into Case I
(when necessary).
●Pour liquid detergent into Case II.
2. Pour laundering additives, such as fabric
softeners, into Case when necessary).
3. Close the drawer securely.
NOTICE: Dilute liquid detergents or additives with
water before pouring it into the detergent dispenser
to prevent the inlet from being blocked and over-
flowing while filling with water.
F. Laundering Fabrics
●Starting the appliance:
1. Load the clothes to be washed into the drum.
2. Add liquid detergent or any other approved
cleaning solvents in drawer (pods go in the
drum).
3. Press the “Power” button.
4. Select the desired cycles and options.
5. Press the “Start/Pause” button.
●Selecting the Wash Cycle:
1. Select the proper wash cycle.
2. Select the proper temperature according
to soil level. Higher temperatures consume
more power.
3. Select the proper spin speed. The higher
the spin speed, the drier the garments will
be before drying.
DO NOT attempt to open the door
while the appliance is running. Doing so may re-
sult in personal injury or property damage. To load
additional clothes into the dryer, press the Pause
button and wait for the door to unlock. The door will
NOT unlock until all the water is drained from the
appliance and the internal temperature drops be-
low 122°F. Press Start only once the door is closed
again. Overflowing water resulting from misuse of
the appliance may cause property damage.

15
TABLE 2
OPERATING INSTRUCTIONS
YD: Default Option
Y: Option Available
N: No-Option
Note: The parameters in this table are only
for user's reference. The actual maybe
different with the above noted.
To prevent personal injury and/or property damage, the door will remain locked until a safe water level and
internal temperature have been reached. This can take a minimum of 45 minutes depending on multiple external factors.
This operation is normal with a washer/dryer combo designed for RVs and other mobile applications.
TABLE OF WASH and Dry Selections
Normal /
Cotton Heavy Duty Sports Bulky Duvet Quick Delicate Wool Under Ware Sanitize
Light YD Y Y Y YD YD Y YD YD N
Med Y Y Y YYY Y YY N
Heavy YYDYDYDYY YD YY YD
Highest YYDY YYY NN
YN
High YD Y YD YD Y YD Y Y YD N
Med YYYYYDYYDYDYN
Low Y Y Y YYY Y YY N
No Spin Y Y Y YYY Y YY N
None YD YD YD NNN N NN N
Light YYYNNN N NN N
Normal YYYNNN N NN N
Heavy YYYNNN N NN N
Cold YYYYYDYYYYD
N
ECO Y Y YD YD Y Y YD YD Y N
Warm YD YD Y Y Y YD Y Y Y N
Hot Y Y Y YYY NN
YN
Hot+ YN N NNN N NN YD
Y Y Y YYY Y YY N
YYYYY
NYYYN
:54 1:34 :51 1:04 :57 :36 :54 1:05 1:21 1:52Default Time hr:min
Time Save
Program
Soil Level
Spin Speed
Dry
Water Temp
Extra Rinse
Spin
Only Rinse & spin Refresh Dry Tub Clean
Light N N N N N
Med NNNNN
Heavy N N N N N
Highest YYNYD N
High YD YD NNN
Med YYNNN
Low YYNNN
No Spin YYNNN
None NNNNN
Light NN N YN
Normal NNYD YD N
Heavy NN N YN
Cold NNNNN
ECO NNNNN
Warm NNNNN
Hot NNNNN
Hot+ NNNNN
NYD NNN
NNNNN
:11 :16 :31 1:47 1:27Default Time hr:min
Extra Rinse
Time Save
Program
Soil Level
Spin Speed
Dry
Water Temp

16
C. Cleaning the Detergent Dispenser and
Grooves
Remove the drawer.
1.1 Pull out drawer.
1.2 Press lever down.
1.3 Remove drawer.
FIG. 19
1.1
1.3
1.2
2. Remove center lever, wash thoroughly,
and replace.
2.1 Lift center lever.
2.2 Wash thoroughly & replace lever.
2.3 Replace drawer.
D. Cleaning the Inlet Filter
●The filter MUST be cleaned if there is little or
no water flow when the tap is opened.
E. Cleaning the Tap Filter
Turn off the tap.
2. Select any cycle except “Wash” or
“Drain”.
3. Press the “Start/Pause” button and keep
the cycle running for approximately 40
seconds.
4. Remove the inlet hose from the tap.
5. Use water to wash the filter if present.
6. Reconnect the inlet hose.
CARE AND CLEANING
Failure to obey the following instruc-
tions could result in death or serious injury due to
fire or explosion.
●Read and understand all safety instructions.
●Before attempting maintenance, disconnect the
power and shut the water valves off.
●Do NOT use unapproved cleaning solvents that
may damage the laundering machine and gener-
ate toxic gases which can explode.
●NEVER spray water on the laundering machine
to clean it.
●Any detergents containing PCMX should NOT be
used to clean the machine.
A. Cleaning the Appliance Cabinet
●Proper maintenance of the appliance can
extend its working life. The surface can be
cleaned with a diluted non-abrasive detergent
when necessary. If there is any water overflow,
use a wet cloth to wipe it off immediately. No
sharp items should be used on the cabinet.
●Do NOT use any acid, diluted solvents, or
equivalent substances to clean the cabinet.
B. Cleaning the Internal Drum
Any rust left inside the drum by metal articles
MUST be removed immediately with chlo-
rine-free detergents. NEVER use steel wool
or any other abrasive cleaning materials.
●Removing the Remaining Water in the Inlet
Hose
Burn Hazard. This step should be
completed after the hot water inside the machine
cools down.
Turn off the tap.
2. Unscrew the inlet hose from the tap and
put its end into a large container to catch
the water.
3. Start any cycle except the Single Wash
or Drain procedure.
4. If there is any water, it will be drained out
of inlet hose for about 40 seconds.
5. Reconnect the inlet hose to the tap.
6. Remove the remaining water in the drain
pump.
FIG. 18
FIG. 20
2.1
2.2
2.3

17
CARE AND CLEANING
F. Washing the Filter in the Appliance
Unscrew the inlet hose from the backside
of the machine.
2. Pull out the filter with long-nose pliers,
and reinstall it after cleaning (see Fig.
21).
3. Reconnect the inlet hose.
4. Turn on the tap, and make sure there is
no water leakage.
G. Removing Foreign Objects
Drain Pump Filter: The filter collects lint and
small foreign objects. Clean it periodically to
ensure normal operation of the appliance.
Drain water may be hot enough
to cause burns. Wait for the water to cool.
Ensure the water has cooled down inside
the appliance.
2. Drain the excess water from the drain
pump using the spin cycle.
3. Disconnect the appliance.
4. Gently clean the pump.
According to the soil level within the cycles
and the frequency of the cycles, regularly
inspect and clean the filter. The pump
should be inspected if the machine does
NOT empty and/or spin, or the machine
makes an unusual noise during draining
due to objects such as safety pins or coins
blocking the pump.
5. Open the service panel. Place a con-
tainer nearby to collect any spillage from
cleaning (see Fig. 22).
6. When water no longer spills out, unscrew
the pump cover and remove it. Always
keep a rag nearby to dry up any spillage
of water when removing the cover.
7. Remove any objects.
8. Fully screw the pump cover in.
9. Close the service panel.
Burn Hazard. When the appliance is
in use there may be hot water in the pump depend-
ing on the cycle selected. NEVER remove the pump
cover during a wash cycle. Wait until the appliance
has finished the cycle and is empty. When replacing
the cover, ensure it is securely tightened to avoid leaks
and to prevent children from removing it.
H. Winterizing/Storing when temperatures
drop below 32° F (0° C):
Remove the remaining water in the drain
pump by running the spin cycle.
2. After spin cycle is complete, disconnect
the power plug or disconnect the power
source.
3. Shut the water valves off, and let any hot
water in the hoses and machine cool be-
fore continuing.
4. Disconnect the drain and inlet hoses,
and drain any excess water.
The hot water hose may still con-
tain hot water.
5. Open the service panel located on the
bottom front-right side of the appliance.
6. Place a container and/or rags close to the
screw cap to collect any excess water.
7. Unscrew to remove cover. Excess water
will drain as the cover is removed.
8. Once all excess water has been re-
moved, replace the cover.
9. Close the service panel.
FIG. 21
FIG. 22
1. Open the
filter's door
2. Turn knob
counter clockwise
2. Pull out coin trap
and drain excess water

18
TROUBLESHOOTING
Problem Reason Solution
Appliance does not
start up
Check that the door is closed tightly. Check that the
power plug is inserted properly. Check that the elec-
tric supply fuse/breaker is not tripped. Check that the
water supply taps are open. Ensure the inlet hose
filters are unobstructed. Check if the “Power” button is
pressed. Check if the “Start/Pause” button is pressed.
Door does not open Water remains in the drum.
Internal temperature is too high.
Water temperature is too high.
The machine’s safety design protections are work-
ing. Disconnect the power. Reconnect the power after
allowing the machine to cool. Continue original cycle.
Run spin cycle if necessary.
Water does not get
warm or hot
The temperature sensor is damaged. Normal laundering can continue, but without hot water.
Contact the service center promptly.
Water leakage The supply hose gasket is missing or
damaged.
The connection between inlet hose
or outlet hose and tap or laundering
machine is not tight. Drain pipe in the
room is blocked.
Check and fasten the water hoses. Clean up the outlet
hose and ask a specialized technician to repair it when
necessary.
Water is overflowing
from the bottom of the
machine
The inlet hose is damaged or not con-
nected firmly.
Outlet hose has water leakage.
The pump service plug is not tight.
Fix the inlet hose. Tighten the pump service plug. Re-
place the drain pipe.
Indicator or display
does not light
Power is disconnected. The PC board
has problems.
Loose wiring connections.
Check if the power breaker/fuse is shut down and
power plug is connected correctly. Contact a qualified
service technician.
Detergent residue in
the dispenser
Powdered detergent was used or liq-
uid detergents were not diluted.
Clean and wipe the dispenser. Use liquid HE deter-
gents or laundry pods per the instructions.
Laundering effects are
not satisfactory
The clothes are too dirty, insufficient
detergent was used, or the wrong
cycle was chosen.
Do not wash heavily soiled fabrics. Select a proper
cycle. Add the proper detergent quantity according to
the instructions on the detergent package.
Abnormal noise or
vibration
Check if the transport bolts have been removed, and
that the cabinet is installed on a solid level floor. Check
if there are any heavy or metal articles inside the drum.
Check if the legs in the laundering machine are prop-
erly leveled.
Frozen appliance/
drain pipe/hose(s)
Appliance was located in a location
where freezing temperatures were
present and water was left in the drain
pipe and/or hose(s).
Verify the vehicle's supply water pipes are not dam-
aged. Disconnect the power supply for the appliance.
Wash the tap with warm water to loosen the inlet hose.
Remove the inlet hose and immerse it in warm water.
Pour warm water into the laundering drum and wait
10 minutes. Reconnect the inlet hose to the tap, and
check that the inlet and outlet are working normally.
Timer display on
same # for extended
period of time.
Large drying loads require extended
time to dry completely. Internal drum
sensor communicates to "pause" the
countdown to ensure maximum drying
level is achieved.
Note: The unit is still functioning properly even if the
timer display is paused. To avoid this "pause" on the
display, dry load size should be less than 7.5lbs.

19
DISPLAY DIAGNOSTIC CODES
Diagnostic Service Codes Description Appliance Action User Corrections
E10 Water fill time exceeds 7
minutes.
Unit will close valves and
stop.
Tap is not open. Check inlet
hose and filters.
E11 There is excessive water
left in the unit during unit
standby or end of cycle.
Unit will start pump with
door locked, valve closed,
and motor stopped.
Check outlet hose for fold-
ing, clogs and grey water tank
level. Run spin cycle to drain
water. Clean pump filter with
caution, prepare for large
amount of water that will drain.
E12 The water level in the drum
exceeds the designed level.
Unit will start pump with
door locked, valve closed,
and motor stopped.
Check outlet hose for fold-
ing, clogs and grey water tank
level. Run spin cycle to drain
water. Clean pump filter with
caution, prepare for large
amount of water that will drain.
E21 In three minutes, the water
level doesn't drain with
pump started.
Unit will pause with pump
stopped, door unlocked if
water level is low enough.
Check outlet hose for fold-
ing, clogs and grey water tank
level. Run spin cycle to drain
water. Clean pump filter with
caution, prepare for large
amount of water that will drain.
E30 Door won't lock in three
tries.
Unit will stop. Check for latch or door seal
blockage. Ensure door is
closed.
E31 Door won't unlock in three
tries.
Unit will stop. Continue original cycle to
completion. Allow appliance to
cool. Run a spin cycle.
E70 Button stuck. No function. Check the buttons. Restart
unit.
Codes E20, 33-40, 64-81, and all others NOT listed above are an internal fault that MUST be corrected by a qualified
service professional. The appliance may NOT work or in a few cases will function but NOT fully as designed. Contact a
Dometic Corporation authorized service representative to repair the appliance.

20
APPENDIX
A. Fabric Care Label References
B. Technical Specifications
Power Supply 120V / 60Hz
Dimension (W*D*H) 23.44”*23.06”*33.44”
(595MM*565MM*850MM)
Weight 174lbs (79kg)
Laundering/Dry Capacity 15lbs (6.8kg)/ 7.5lbs (3.4kg)
Rated Current 12A
Standard Water Pressure 7.3-145 psi (0.05MPa-1MPa)
Max. Spin Speed 1200 rpm
Record this information for future reference:
Model Number:
Serial Number:
Date Purchased: