Dongguan Sen Dong Lv Electronics B1326 User manual

B1326
蓝牙无线耳机
快速操作指南
包装内容
外观
使用方法
● 连接设备
● 播放控制
● 电话控制
● 耳机充电
● 开/关机
1.耳机
2.USB充电线
1.音量 + 按键
5.音量 - 按键
2.多功能按键
6.USB接口
3.LED指示灯
LED指示灯
4.麦克风
● 长按多功能键3秒，蓝色指示灯
闪3次，语音提示“嘟嘟”
LED指示灯
开机
关机
复位
● 长按多功能键约3秒,红色指示灯
闪3次,语音提示“嘟”
● 长按多功能按键8S,恢复出厂
设置。
在配对之前，请确保您的耳机有足够的电量并确保您的连接设
备在有效的使用范围之内进行配对和连接。
● 配对
打开您的B1326耳机，按住多功能键
约5秒。红蓝指示灯快速交替闪烁表示
B1326 进入到配对模式和准备配对连
接到您的蓝牙设备。语音提示“滴”
● 连接成功
蓝牙设备搜索B1326并连接，蓝色指示
灯7S闪一次。
● 配对超时
红蓝色指示灯快速交替闪烁，3分钟后
没有与手机连接将会自动关机。
● 连接断开
设备端人为把蓝牙断开连接，蓝色指示
灯3秒闪一次，5分钟后没有与手机连接
，红色灯闪三次关机。
● 同时连接两部手机
成功配对到第一台手机后关闭B1326重新开机进入到配对状态，
然后连接上第二台手机后耳机再次关机，然后开机会自动连接
到第二台手机，在手机上手动点连接第一台手机。蓝色指示灯
1秒闪烁3次。语音提示“嘟”。
在您的无线蓝牙设备：iPhone、iPad、iPod及Android
智能手机或者平板电脑
● 在您的蓝牙设备上打开“设置”功能。
● 确保您的蓝牙设备上的“蓝牙”选项是打开的，点击“搜索”
功能。
● 等待B1326的蓝牙名称显示在“可用设备”的蓝牙列表中。
● 选择B1326蓝牙名称，开始与您的蓝牙设备进行配对和连接。
●
在您的 B1326 无线蓝牙耳机与手机连接时，蓝色指示灯7秒闪烁2
次表示您的无线蓝牙耳机已经配对成功，您可以开始播放和聆听您
喜欢的音乐。
● 单击 音量加
长按 下一曲
● 单击 音量加
● 单击 音量减
● 单击 音量减
长按 上一曲
● 单击 多功能键 播放/暂停
● 单击多功能键接听电话
● 长按多功能键约2秒，
拒绝来电
● 通话过程中短按多功能键
结束通话
● 您的B1326无线蓝牙耳机的电池在出厂时只充了一部分电，我
们建议您先充满电后再播放，这样可以让播放时间最长久。
● 红色恒亮 – 表示电池正在充电。
蓝色恒亮 – 表示电池已经充满。
●
低电量
当电压降低到3.4V以下， 每隔7秒红色指示灯闪2次。
● 轻轻地插入 Micro USB线到耳机的Micro USB接口,轻轻地插入
Micro USB线的另外一头到带USB接口的充电器或者电脑的
USB接口给耳机电池充电，需要1.5小时充满电池。
备注：在插入USB线给耳机充电时，为了保护电池寿命，此时在
耳机上长按多功能按键不能开机，需要拔出USB线后,长按多功能
按键使耳机开机。
● 规格参数
● 注意事项
● 电池：90mAh
● 输入电压：5V/65mA
● 充电时间：1.5hours
● 待机时间：100hours
● 播放时间：≥5hours
● 蓝牙连接距离：≥10m
● 操作、存储和充电温度：0℃-40℃
● 为安全起见，骑自行车、摩托车或驾车时请勿使用耳机。音量
开得过大而无法听清外面声音会很危险；请留意周围车辆谨慎
驾驶。
● 请勿拆卸、摔碰、挤压本产品。
● 请勿本产品置于高温、潮湿环境下。
● 请勿本产品投入火中、水中或含有腐蚀性的液体里。
● 充电时请勿将本产品放在易燃物质上。
● 如自行拆卸更换内置电池，可能存在爆炸危险。
● 避免音量过大或长时间大音量佩戴耳机，以免听力受损。
● 常见问题
如果B1326无线蓝牙耳机不开机？
● 检查您的B1326无线蓝牙耳机的电池有足够的电量。
● 如果您的电脑自身的电池耗尽了，您电脑的USB端口将无法给
B1326的电池进行充电，请尝试用5V(1A或2A)的USB充电器
给B1326的电池进行充电，充电时间至少要充2-3小时。
如果播放音乐耳机没声音？
● 检查播放装置与蓝牙耳机是否建立有效连接，若音频设备未能
正常连接，请重新连接，同时调整手机和蓝牙耳机的音量到合
适的音量等级。
如果手机无法搜索到蓝牙耳机？
● 请确认手机蓝牙是否处于“设备可见模式”，若长时间未进行
配对，蓝牙配对功能自动关闭，请重新开启蓝牙至“设备可见
模式”。若手机程序出错，请重启手机；若蓝牙耳机程序出错
请重启蓝牙耳机。

Package Contents
Appearance
Instructions
● Connect equipment
● Play Control
● Phone control
● Headphone charging
● Power ON /OFF
1.Earphone
2.USB charging cable
1.Volume + button
5.Volume- button
2.Multifunction button
6.USB charging port
3.LED indicator
LED indicator
4.Microphone
● Press and hold the multi-
function button for 3 seconds.
The blue indicator flashes 3
times and the voice prompts
"Beep".
LED indicator
Power ON
Power OFF
Reset
● Press and hold the multifunction
button for about 3 seconds.
The red indicator flashes 3
times. The voice prompts
“Beep”.
● Press and hold the multifunction
button for 8 seconds to restore
the factory design settings.
Before pairing, make sure that your headphone has
enough power and that your connect source device is
paired and connected within the effective range of use.
● Pairing
Turn on B1326 headphone and
press the multifunction button
for about 5 seconds.
Red and blue lights flash alternately
indicating that the EN61 enters
pairing mode and is ready to
connect to your Bluetooth device.
Voice prompt "pairing".
● Successful connection
The Bluetooth device searches for
EN61 and connects, and the blue
light flashes quickly.
● One Press Volume +
Long press next track
● One Press Volume up
● One Press Volume down
Long press play previous
● One Press Volume -
Long press play previous
● One Press Multifunction
button Play/Pause
● One Press the multi-function
button to answer the call
● Press and hold the multifunction
button for about 2 seconds to
reject the call
● Short press the multifunction
button to end call
● Low Power
When the battery power lower less than 15%, there will be
a "beep beep" voice prompt ,every 7 seconds the red
indicator will flash 2 twice.
● Gently insert the Micro USB cable into the Micro USB
charging port of the headphone, and gently insert the other
end of the Micro USB cable into the USB port of the charger
or the computer's USB port to charge the headphone. It
takes 1.5hours to fully charge the battery.
Note: When using the USB cable to charge the
earphones, in order to protect the battery life, long
press the multifunction button can not boot the
earphone. , You need to pull out the USB cable, long
press the multifunction button to boot the earphone.
● Specifications
● Attention
● Battery: 80mAh
● Input voltage: 5V/65mA
● Charging time:1.5hours
● Standby time: 80hours
● Playing time: ≥5hours
● Bluetooth connection distance: ≥10m
● Operation, storage and charging temperature: 0°C-40°C
● For safety, do not use headphones when riding a bicycle,
motorcycle, or driving. It is dangerous to open the
volume too loud and can not hear outside sounds. Please
pay attention to careful driving and surrounding vehicles.
● Don’t disassemble, avoid dropping.
● Do not place this product in a hot, humid environment.
● Do not put this product into fire, water, or corrosive
cleaner.
● common problem
If B1326 wireless Bluetooth headphone does not turn on?
● Check if the battery of your B1326 wireless Bluetooth
headphone has enough power.
● If your computer's own battery is exhausted, your
computer's USB port will not be able to charge the
EN61's battery. If charging the B1326's battery with a
5V (1A or 2A) USB charger, charging time should be at
least Charge 2-3 hours.
If there is no sound in the headphones when you play
music？
● Check whether the device and the Bluetooth headphone
establish a valid connection. If the audio device fails to
connect properly, reconnect it and adjust the volume of
the phone and Bluetooth headphone to an appropriate
volume level.
If the phone cannot search the Bluetooth headphone?
● Please confirm whether the Bluetooth of the mobile
phone is in the “Device Visible Mode”. If the pairing is
not performed for a long time, the Bluetooth pairing
function will be automatically closed. Please turn
Bluetooth on again to “Device Visible Mode”. If there
is phone program error, please restart the phone; if
headphone bluetooth goes wrong, please restart the
Bluetooth.
Bluetooth Wireless Earphone
MODEL:B1326
User Manual
● Pairing timeout
The red and blue lights quickly flash alternately and turn off
automatically after 3minutes. Voice prompt "beep."
● Disconnect
Manually disconnect the Bluetooth on the device,and the red
indicator will flash quickly after 5 minutes.The connection
between the device and the B1326 is out of the valid range
(10 meters) .The blue light indicates “beep” every 15
seconds for the first 5 minutes and turns off after 5 minutes.
● Connect two mobile phones at the same time
After successfully pairing to the first phone, close B1326
and reboot to enter the pairing state. After connecting the
second phone, turn off the headphone again. Then the
connection will be automatically connected to the second
phone, manually connect the first mobile phone on the
phone. The blue light flashes 3 times for 1 second.
In your wireless Bluetooth device: iPhone, iPad, iPod and
Android smartphone or tablet.
● Open the "Settings" feature on your Bluetooth device.
● Make sure the "Bluetooth" option on your Bluetooth
device is turned on. Click the "Search" function.
● Wait for the B1326’sBluetooth name to appear in the
Available Devices' Bluetooth list.
● Select the B1326 Bluetooth name and start pairing and
connection with your Bluetooth device.
● The blue light on your B1326 wireless Bluetooth earphone
flashes quickly, indicating that your wireless Bluetooth
earphone has been paired successfully and you can start
playing and listening to your favorite music.
● The battery of your EN61 wireless Bluetooth headphone
is only partially charged at the factory. We recommend
that you fully charge the battery before playing it. This
will allow you to enjoy the longest play time.
● Steady red charging
Steady blue full charged
● Do not place this product on flammable substances
when charging.
● If you remove or replace the internal battery by yourself,
there is a risk of explosion.
● Avoid excessive loud volume or wear headphones for a
long time to avoid hearing loss.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RFexposure requirement. The device can be u
sed in portable exposure condition without restriction
Warning:
Products suffer from static electricity and need to be manually connected.