Door Knox VDP300 User manual
DoorKnox PhoneSEE WiFi Box
xVDP300
DoorKnox.com
© 2021 System Q Ltd
VDP300
I
© 2021 System Q Ltd
DoorKnox.com
Table of Contents
Part 1 Introduction 1
1 Key Features ............................................................................................................................................................. 1
Part 2 Connections 2
1 Overview .................................................................................................................................................................... 2
2 Input Connections .................................................................................................................................................... 3
3 Output Connections ................................................................................................................................................. 4
Part 3 LED Indicators 5
Part 4 Controls 6
Part 5 Mounting 7
Part 6 Smart App 8
Part 7 Network Setup 9
1 EZMode Setup .......................................................................................................................................................... 9
2 Cable Mode Setup ..................................................................................................................................................12
3 AP Mode Setup ....................................................................................................................................................... 15
Part 8 Using the App 19
1 Visitor Calls ........................................................................................................................................................... 19
2 AppControls ........................................................................................................................................................... 19
Part 9 SD Card 20
Part 10 Signal Setup 20
Part 11 DoorKnox Wiring 21
1 Cameras .................................................................................................................................................................. 21
2 Monitors .................................................................................................................................................................. 21
3 Powering Cameras ................................................................................................................................................ 21
4 Powering Monitors ................................................................................................................................................ 21
5 Cable Runs .............................................................................................................................................................. 22
Part 12 Troubleshooting 23
1 Signal Loss / No Image ......................................................................................................................................... 23
Part 13 General Maintenance 23
Part 14 Specification 24
Part 15 Conditions 25
1 Tuya Smart App ..................................................................................................................................................... 25
Index 26
Introduction
1
© 2021 System Q Ltd
DoorKnox.com
1 Introduction
The VDP300 PHONESEE WiFiDoorKnox box is used to integrate DoorKnox cameras and
monitors for remote viewing and door relay controlvia the "Tuya Smart"application.
The VDP300 is installed betweenDoorKnox cameras and DoorKnox monitors to intercept the
images to streamand connect withthe Tuya Smart app via the WiFior via a Ethernet network
cable connected to a router.
1.1 Key Features
·
Remote monitoring
·
Remote relay control
·
Push notifications
·
Wi-Fipairing
·
LED connection indicators
·
SD card recording
VDP300
2
© 2021 System Q Ltd
DoorKnox.com
2 Connections
2.1 Overview
The VDP300 is installed between DoorKnox cameras and DoorKnox monitors in order to
intercept the images to streamand connect withthe Tuya Smart app via the WiFior anEthernet
network cable connected to a router.
Connections
3
© 2021 System Q Ltd
DoorKnox.com
2.2 Input Connections
VDP300
4
© 2021 System Q Ltd
DoorKnox.com
2.3 Output Connections
LED Indicators
5
© 2021 System Q Ltd
DoorKnox.com
3 LED Indicators
PowerLED
ON = Device is powered
Note:-
During boot-up the WIFI, SERVER and SIGNAL LEDs willbe ON
Once boot-up is complete the WIFI, SERVER and SIGNAL LEDs willturn OFF
WIFI LED
ON = Network ok
OFF = Network disconnected
Fast flash = Configuring network
Slow flash = EZ mode
SERVER LED
ON = Server connection ok
OFF = Server disconnected
Slow flash = WIFI setup mode
SIGNAL LED
See SignalSetup
20
VDP300
6
© 2021 System Q Ltd
DoorKnox.com
4 Controls
The controlbuttons on the back ofthe VDP300, are shown below.
S-link (Only use ifthe SERVER light is not on solid)
Short Press (>1s) = Restarts the VDP300 and starts "EZ Mode", the WIFI LED will
flash slowly. See EZ Mode Setup
AP (Only use ifthe SERVER light is not on solid)
See AP Mode Setup
SignalSee SignalSetup
ResetLong press (5s) = Factory default the VDP300.
Channel (Dip-switches)
See SignalSetup
9
15
20
20
Mounting
7
© 2021 System Q Ltd
DoorKnox.com
5 Mounting
The VDP300 Hub canbe mounted usingthe screws provided and the mountingholes onthe
rear.
Network Setup
9
© 2021 System Q Ltd
DoorKnox.com
7 Network Setup
The VDP300 WiFibox canbe setup with3 different modes; EZ Mode, AP Mode, Cable
Mode.
7.1 EZ Mode Setup
The VDP300 WiFi box can be paired up with a router (wirelessly) using the S-link pairing button
on the back ofthe VDP300 and the "Tuya Smart"app.
1. Press the S-link to start the EZ pairing. The WiFiLED willflash slowly when in pairing mode
2. Open the "Tuya Smart"app, select “Add Device” or
press the “+”at the top right to add a device
3. Select "Video Surveillance"category on the left,
then select "Smart Doorbell"
VDP300
10
© 2021 System Q Ltd
DoorKnox.com
4. At the top right, select "EZMode"
5. Tick "Next Step", then select Next
6. Select the WiFiHub (Router or Access point) and
enter the WiFi password, then select Next
Network Setup
11
© 2021 System Q Ltd
DoorKnox.com
7. The WiFiLED will flash quickly once it starts pairing
8. Once paired the app willshow the device is Added
VDP300
12
© 2021 System Q Ltd
DoorKnox.com
7.2 Cable Mode Setup
The VDP300 canbe connected to a router directly usingthe RJ45 network port for remote
viewing and door relay controlvia the "Tuya Smart"application.
1. Connect anEthernet (CAT5 / 5e / 6) cable to the RJ45 port on the back of the VDP300.
(The network port LED indicators willlight up once connected)
2. Press the S-link to start pairing. The WiFi LED willflash slowly when in pairing mode
3. Open the "Tuya Smart"app, select “Add Device” or
press the “+”at the top right to add a device
4. Select "Video Surveillance"category on the left,
then select "Smart Doorbell"
5. At the top right, select "Cable Mode"
VDP300
14
© 2021 System Q Ltd
DoorKnox.com
9. The app willthen try to add the device via the
network
10. The app willshow the device is Added
Network Setup
15
© 2021 System Q Ltd
DoorKnox.com
7.3 AP Mode Setup
The VDP300 WiFi box can be paired up with a router (wirelessly) using the AP button on the
back ofthe VDP300 and the "Tuya Smart"app.
1. Press the AP button to set the VDP300 to access point mode.
2. On the mobile phone / tablet navigate to the WiFi
settings
Search for "SmartLife-xxxxxx", connect using the
password "12345678"
3. Open the "Tuya Smart"app, select “Add Device” or
press the “+”at the top right to add a device
4. Select "Video Surveillance"category on the left,
then select "Smart Doorbell"
VDP300
16
© 2021 System Q Ltd
DoorKnox.com
5. At the top right, select "AP Mode"
6. Tick "Next Step", then select Next
7. Use the switch button to connect to the main WiFi
Hub (Router or Access point).
Network Setup
17
© 2021 System Q Ltd
DoorKnox.com
8. Go back to the Tuya Smart app and select Next
9. Click "Go to Connect"to connect the mobile phone
back to the "SmartLife-xxxxxx"WiFi. Thengo back to
the Tuya Smart app.
VDP300
18
© 2021 System Q Ltd
DoorKnox.com
10. The WiFiLED will flash quickly once it starts pairing
11. Once paired the app willshow the device is Added
Table of contents
Other Door Knox Intercom System manuals
