DoorBird A1081 Series User manual

1
ENGLISH
VERSION ., MIN. HW .
Page 2-18
Installation Manual
IP I/O Door Controller
A1081 Series
Seite 19-37
Installationsanleitung
IP E/A Tür Controller
A1081 Serie
Page 38-55
Manuel d‘installation
Commande de porte
IP E/S
Série A1081
A1081

2
INSTALLATION MANUAL
Read these instructions carefully before starting to use any components. Keep
the manual so you can refer to it at a later date if required. If you hand over the
device to other persons for use, please hand over the operating manual as well.
You can always find the most up-to-date version of the installation manual on
www.doorbird.com/support
To make things easier we use the term “device” for the product “IP I/O Door
Controller” and “mobile device” for a smartphone or tablet.
Liability
Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions.
Bird Home Automation GmbH cannot be held responsible for any technical
or typographical errors and reserves the right to make changes to the product
and manuals without prior notice. Bird Home Automation GmbH makes no
warranty of any kind with regard to the content of this document, including,
but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Bird Home Automation GmbH shall neither be liable nor
responsible for incidental or consequential damages in connection with the
furnishing, performance or use of this material. This product is only to
be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no
components that require service by the user. Unauthorized equipment
changes or modifications will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Caution: Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Danger: Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Warning: Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

3
ENGLISHENGLISH
3
Notice: Indicates a situation which, if not avoided, could result
in damage to property.
Note: Indicates useful information which helps in getting the
most out of the product.
NOTICE
Hazard information
 Mounting, installation and servicing work on electrical devices may
only be performed by a qualified eletrician. Failure to observe this
regulation could result in the risk of serious damage to health or fatal
injury due to electric shocks.
 Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must
be pulled out if a hazard occurs.
 For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.
 Because of electrostatic charging, direct contact with the circuit
board can result in destruction of the device. Direct contact with the
circuit board must therefore be avoided at any time.
 Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
 Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have
the device checked by an authorized expert.
 Do not open the device. This voids the warranty of the device.
The device does not contain any parts that can be maintained by the
user. In the event of an error, please have the device checked by an
authorized expert.
WARNING
Important: Indicates significant information which is essential
for the product to function correctly.

44
 For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized
change and/or modification of the device is not permitted.
 The device is not a toy; do not allow children to play with it. Do not
leave packaging material lying around. Plastic films/bags, pieces of
polystyrene, etc. can be dangerous in the hands of a child.
 Always lay cables in such a way that they do not become a risk to
people and domestic animals.
 Voltage is applied to parts within the equipment. Do not touch any
parts that are not associated with the installation, wiring, or connection.
Electric shock could result.
 On devices which are not marked as weather-proof: Keep the device
away from water or any other liquid.
 Do not install or make any wire terminations while power supply is
plugged in. It can cause eletric shock or damage to the device.
 Before turning on power, make sure wires are not crossed or shorted.
If not, fire or eletric shock could result.
 High voltage may be present internally. Do not open the device.
Electric shock could result.
 The device is not of explosion-proof. Do not install or use near gases
or flammable materials. Fire or explosion could result.
 Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power
supply to the device.
 Do not connect any terminal on the device to an AC power line. Fire
or electric shock could result.
 Keep AC cord from being marred or crushed. If the AC cord is fractured,
fire or electric shock could result.
 Do not plug or unplug with wet hands. Electric shock could result.
WARNING

5
ENGLISHENGLISH
5
 Do not put any metal or flammable material into the device.
Fire, electric shock, or device trouble could result.
 Existing wiring such as chime wiring, etc. may contain high voltage
AC electricity. Damage to the device or electric shock could result.
Wiring and installation must be done by a qualified eletrician.
 When mounting the device on a wall or ceiling, install the device in
a convenient location, but not where it could be jarred or bumped.
Injury could result.
 On devices with ground terminals, connect to an earth ground.
Otherwise fire or malfunction could result.
 On devices with plastic or real glass, do not put high pressure on
the glass. If fractured, injury could result.
 On devices with LCD, if LCD is punctured, do not allow contact
with the liquid crystal inside. Injury could result. If necessary, gargle
your mouth and clean your eyes or skin with clear water for at least
15 minutes and consult your doctor.
 Do not put anything on the device or cover the device with cloth,
silicone, glue, coating, separate covering etc. Fire or device issues
could result.
 Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.
- Places under direct sunlight or places near heating equipment that
varies in temperature.
- Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
- Places subject to moisture and humidity extremes, such as bathrooms,
cellars, greenhouses, etc.
- Places where the temperature is very low, such as inside a refrigerated
area or in front of an air conditioner.
- Places subject to steam or smoke (e.g. near heating or cooking surfaces).
- Where noise generating devices such as dimmer switches or inverter
electrical appliances are closeby.
- Locations subject to frequent vibration or impact.

66
 On devices with intercom, be sure to perform a call test with low
audio volume on both intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.
 If the device does not operate properly, unplug the power supply.
 All devices which are not marked as weather-proof are designed for
indoor use only. Do not use outdoor.
 On devices which are marked weather-proof: Do not spray with
high-pressure water. Device issues could result.
 We do not assume any liability for damage to property or personal
injury caused by improper use or the failure to observe the hazard
information. In such cases, any claim under warranty ceases.
For consequential damages, we assume no liability!
WARNING
Safety instructions
 The device shall be used in compliance with local laws and regulations.
 Store the device in a dry and ventilated environment.
 Avoid exposing the device to shocks or heavy pressure.
 Do not install the device on unstable brackets, surfaces or walls.
Make sure the material is strong enough to support the weight of
the device.
 Use only applicable tools when installing the device. Using excessive
force with tools could cause damage to the device.
 Do not use chemicals, caustic agents, or aerosol cleaners.
 Use a clean dry cloth for cleaning.
 Use only accessories that comply with technical specification of the
device. These can be provided by Bird Home Automation GmbH.
 Use only spare parts provided by or recommended by Bird Home
Automation GmbH.
 Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.
NOTICE

7
ENGLISHENGLISH
7
 Keep the device more than 1 m (3.3') away from microwave, radio, TV,
wireless router and any other wireless devices.
 On devices with intercom or built-in speaker or built-in microphone
or signal transmission functions, keep the wires more than 30 cm (12'')
away from AC 100-240 V wiring. AC induced noise and/or device
malfunction could result.
 Install the device in an area that will be accessible for future inspections,
repairs and maintenance.
 If the device is used close to a cellular phone, the device may malfunction.
 The device can be damaged if dropped. Handle with care.
 The device turns inoperative during power failure.
 On devices with intercom or built-in speaker or built-in microphone,
in areas where cellular or Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio frequency interference.
 On devices with LCD screen, it must be noted in advance that the LCD
panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its picture elements always lit
or not lit at all. This is not considered a device malfunction.
 On devices with intercom, due to the environmental sound around
the device, it may hinder smooth communication, but this is not a
malfunction.
 On devices with Username/Password, the Username/Password to
access the device is the customer's responsibility. Make sure to use
password that cannot be easily guessed by a third party.
We recommend that you change the Password on a regular basis.
 We will, under no circumstances, be liable for damage that occurs due
to failures in power supply, network equipment or terminal devices;
failures due to Internet providers and cellular network providers;
failures such as disconnected lines and other losses in communication,
which makes it impossible to provide this service as well as in any way
delay this service due to any other causes outside of our responsibility;
or if an error or missing data occurs during transmission.

88
Warranty Information
For information about the device warranty, see www.doorbird.com/warranty
Transportation
When transporting the device, use the original packaging or
equivalent to prevent damage to the device.
COMPONENTS
NOTICE
1x Device
1x Drilling template
1x RJ45 network cable 1x DIN-Rail adapter1x 2,4 GHz Antenna
2x Phillips countersunk head
screws and dowels
1x Quickstart guide
with Digital Passport
1x Installation manual
1x Screw connection
terminal plug
1x Power supply unit (mains adaptor)
with four country-specific adaptors

9
ENGLISHENGLISH
1) WiFi Antenna thread
Antenna thread to connect the
2.4 GHz WiFi Antenna supplied
with the device.
2) Loudspeaker
Loudspeaker for Diagnostic-
Sounds.
3) Diagnostic-LED
Diagonstic LED to visualize the
current status of the device.
4) Screw connection terminal
Screw connection terminal to
connect external devices such as
electric door openers and power
to the device.
5) Setup button
Setup button (SET) of the device,
to e.g. configure the WiFi interface
of the device using the DoorBird
App.
6) LAN/PoE jack
RJ45 jack to connect a
standard Network cable Cat.5
or better, coming from the
Internet Router/PoE-Switch/
PoE-Injector.
Device
WiFi Antenna
thread
Loudspeaker
Diagnostic-LED
Screw connection
terminal
Setup button
LAN/PoE jack
1
2
3
4
5
6
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.

1010
INSTALLATION
All the steps below should be carried out carefully by a competent adult,
taking into consideration any applicable safety regulations. Should you have
any questions, please contact us or a competent specialist directly.
Please ensure that all wires used for the installation are undamaged along
their entire length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App.
The user experience is only as good as your network speed, network stability
and quality of your network components, such as your Internet Router and
WiFi access points or WiFi repeaters. Please also make sure that your network
components are no older than two years old, have been manufactured by a
well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may occur, for example that the
performance of audio and video is poor or push notifications are delayed or
do not arrive on your smartphone or tablet at all.
Requirements:
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP
SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location,
i.e. the door chime, electric door opener, power supply unit for the
video door station etc..
DETERMINING THE ASSEMBLY LOCATION
The device is IP50 certified (not water-proof). Please make sure to
put the device into an appropriate housing if you want to use it
outdoors.
The network cable between the device and the PoE-Switch/PoE-Injector/
Internet Router can have a maximum length of 80 meters/262 feet.
You can mount the device permanently on a wall or ceiling. If you do not
want to mount it permanently, please skip the rest of this step.

11
ENGLISHENGLISH
Press the drilling template of the device against the wall or ceiling at the
desired installation site and mark the boreholes with a pencil. Remove the
drilling template again.
Ensure that no cables are to be found in the wall or ceiling
behind the boreholes.
If the wall of the house is not made of wood, you should drill dowel holes
5 mm in diameter in the wall according to the drilling template and then
place the dowels provided into the boreholes. If the wall of the house is
made of wood, you will usually not require any dowels. There are special
dowels for assembling the device on an insulating wall, e.g. Fischer insulating
dowels. Please check with your insulating material manufacturer regarding
which dowels they recommend.
Use the Phillips countersunk head screws provided to position it in the
dowels or on the wall, so that the countersunk head screws protrude a few
millimeters above the wall.
WIFI ANTENNA
The device has a built-in 2.4 GHz WiFi interface, to connect it wirelessly to your
Internet Router. Please assemble the WiFi antenna supplied with the device
to the WiFi antenna thread of the device. The WiFi interface of the device is
automatically inactive if you use a network cable to connect the device to your
PoE-Switch/PoE-Injector/Internet Router.
POWER SUPPLY OPTIONS
The device can be powered using the power-supply unit (mains adaptor)
supplied with it (Option 1) or via PoE (Power over Ethernet) using a network
cable (Option 2). The device can be alternatively also be supplied with power
using a DIN-rail power supply unit that you can obtain direclty from us.
The device does not use battery power.
OPTION 
Power supply using the power
supply unit (mains adaptor)
The power supply unit (mains adaptor) supplied with the device has a 300 cm
long cable with two insulated wires.

1212
NOTICE Do not plug the power supply unit into the wall socket yet. Only use
the power supply unit provided along with the device, or a DIN-rail
power supply unit that you can obtain from us separately, since this
has been specially stabilized electrically and is equipped with an
integrated audio interference reduction device. Other power
supply units may destroy the device or cause poor transmission
quality. The warranty expires automatically if you use a different
power supply unit.
OPTION 
Power supply via PoE
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector
(e.g. DoorBird Gigabit PoE Injector) in accordance with the PoE standard
IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a
Cat.5 cable or better are to be used. A Cat.5 cable or better must be used
as network signals can only be transmitted over completely insulated,
shielded and twisted cables. If you use PoE as a source of power, the WiFi
interface of the device is automatically inactive, and the four wires for PoE
then simultaneously form the data link. The device won’t start if your PoE-
Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af Mode
A (see Diagnostic-LED and Diagnostic-Sounds).
1.Disconnect the PoE-Switch or PoE-Injector from the power grid.
2.Run the network cable to the installation location of the device.
You can find further information about PoE here: http://www.doorbird.com/poe
 CONNECTING THE DEVICE
It is possible to connect the cables and wires to the device conveniently and
safely via labelled connection ports. You can connect all necessary cables
and wires to the device now. Please remove any cables and wires from the
connection ports of the device that you do not need.
Remove about 5 mm of insulation material at the end of the wires that you
would like to connect to the green screw connection terminal of the device.
PORT DESCRIPTION

13
ENGLISHENGLISH
REL1 REL2 REL3 EXT1 EXT2 15VDC
max. 24 V, 1 A max. 24 V, 1 A
15 V DC, 1A
max. 24 V, 1 A
max. 0 V, 0 A
LAN/POE RJ45 jack to connect a standard Network cable Cat.5
or better, coming from the Internet Router/PoE-Switch/
PoE-Injector.
NOTICE Do not power the device simultaneously via
the power supply from the power supply unit
(mains adaptor) and the power supply via PoE.
REL1, REL1
REL1
REL1
Bi-stable latching relay #1 (potential-free),
max. 24 V DC/AC, 1 A. Security feature: The relay keeps
its state even in the case of loss of power. You can
configure the default state of the relay (open/close) via
the DoorBird App. These ports can be used to connect
e.g. an electric door opener. The device does not supply
power to the connected device. The power supply for the
electric door opener must be installed separately.
REL2, REL2
REL2
REL2
Bi-stable latching relay #2 (potential-free),
max. 24 V DC/AC, 1 A. Security feature: The relay keeps
its state even in the case of loss of power. You can
configure the default state of the relay (open/close) via
the DoorBird App. These ports can be used to connect
e.g. an electric door opener. The device does not supply
power to the connected device. The power supply for the
electric door opener must be installed separately.

1414
REL3, REL3
REL3
REL3
Bi-stable latching relay #3 (potential-free),
max. 24 V DC/AC, 1 A. Security feature: The relay keeps
its state even in the case of loss of power. You can
configure the default state of the relay (open/close) via
the DoorBird App. These ports can be used to connect
e.g. an electric door opener. The device does not supply
power to the connected device. The power supply for the
electric door opener must be installed separately.
EXT1, EXT1
EXT1
EXT1
External input 1, max. 0 V DC/AC, 0 A. These ports can
be used to connect e.g. an external sensor, e.g. door
sensor or motion sensor.
NOTICE Please make sure to add no extra voltage on
these ports.
EXT2, EXT2
EXT2
EXT2
External input 2, max. 0 V DC/AC, 0 A. These ports can be
used to connect e.g. an external sensor, e.g. door sensor
or motion sensor.
NOTICE Please make sure to add no extra voltage on
these ports.
15 VDC - 15 VDC Power supply input, negative pole (-). Please
connect the black wire of the power supply unit (mains
adaptor) supplied with the device here, if you do not
power the device using PoE.
NOTICE Do not power the device simultaneously via the
power supply from the power supply unit (mains
adaptor) and the power supply via PoE.
15 VDC + 15 V DC Power supply input, positive pole (+). Please
connect the red wire of the power supply unit (mains
adaptor) supplied with the device here, if you do not
power the device using PoE.
NOTICE Do not power the device simultaneously via the
power supply from the power supply unit (mains
adaptor) and the power supply via PoE.
NOTICE Please take care when connecting the cables and wires. Connecting
the cables and wires the wrong way may damage the device.

15
ENGLISH
 FINAL ASSEMBLY
Mount the device on the Phillips countersunk head screws you already
positioned in step 2, if you want to mount the device permanently on a wall
or ceiling.
ACTIVATING THE DEVICE
Switch on the power leading to the assembly location.
If you use the the power supply unit (mains adaptor) to power the device, plug
it into into a wall socket. If you use PoE to power the device, make sure to
switch on power of the PoE-Switch / PoE-Injector that you have connected the
device to.
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adaptor) and the power supply via PoE.
You can see if the device receives power by checking the Diagnostic-LED,
which lights up about 30 to 60 seconds after the device gets connected to
power. The device is ready for operation (booting up process, any software
updates, etc.) once it has emitted a short diagnosis sound from the integrated
loudspeaker. This may last for up to 5 minutes. If the Diagnostic LED does not
light up, please check the power supply.. When using a wall-plug power
supply and not PoE please check whether you have connected the positive
pole and negative pole to the device correctly.
DOWNLOADING AND INSTALLING THE APP
Download the “DoorBird” App by Bird Home Automation onto your mobile
device from the Apple App Store or Google Play Store. You can always find the
most up-to-date version of the App manual on www.doorbird.com/support
If you use WiFi for connecting the device to your Internet Router, first go to
the DoorBird App “Settings →WiFi Setup” and follow the instructions.
If you have finished the WiFi setup or have connected the device to your
Internet Router by means of a network cable, go to the DoorBird App “Settings
→Administration” and log in to the Administration area of the DoorBird Video
Door Station (using the authentication details of the desired Video Door
Station!) you would like to pair the device with (using the authentication details
of the desired Video Door Station!). To pair the device there, go to “Peripherals
→Settings →Add”.
ENGLISH

1616
If you have problems adding the device to the App please check if the device
is online (www.doorbird.com/checkonline). If the device is not online, please
check the WiFi or network cable connection again.
DIAGNOSTIC-LED
You can see if the device is powered on by checking the Diagnostic-LED,
which lights up about 30 to 60 seconds after the power is connected.
DIAGNOSTIC-SOUNDS
The device emits brief diagnostic sounds about 30 to 60 seconds after it has
been connected to power.
TECHNICAL SPECIFICATIONS
Dimensions 122 x 86 x 32 mm (L x W x H)
4.8 x 3.39 x 1.26 in (L x W x H)
Power supply 15 V DC or power over Ethernet (PoE 802.3af mode A)
Operating
conditions
-25 to 55°C / -13 to 131°F
Humidity 10 to 85 % RH
(non condensing)
Connectors
SMA, RJ45 (10/100 Base-T) for LAN/PoE, 12-pin screw
terminal for
• 15 V DC input (+, -)
• Bi-stable latching relay #1, max. 24 V DC / AC, 1 A
• Bi-stable latching relay #2, max. 24 V DC / AC, 1 A
• Bi-stable latching relay #3, max. 24 V DC / AC, 1 A
• External input 1 (potential-free)
• External input 2 (potential-free)
2.4 GHz, 802.11 b/g/n, external antenna
PoE IEEE 802.3 af/at (Mode-A)
System
requirements
Mobile end device: latest iOS on iPhone/iPad, latest
Android on smartphone/tablet
Internet: High-speed landline broadband Internet
connection, DSL, cable or fiber, no socks or proxy server
Network: 802.11 b/g/n 2.4 GHz or Ethernet Network, with
DHCP
Compatible with all DoorBird IP Video Door Stations.

17
ENGLISHENGLISH
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird
Home Automation GmbH.
2. Apple, the Apple logo, Mac, Mac OS,
Macintosh, iPad, Multi-Touch, iOS, iPhone
and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are
trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are
registered trademarks of Bluetooth SIG, Inc.
5. All other company and product names may
be trademarks of the respective companies
with which they are associated.
6. We reserve the right to make changes to
our products in the interests of technical
advancement. The products shown may also
look different from the products supplied
based on ongoing enhancement.
7. Reproducing or using texts, illustrations and
photos from this instruction manual in any
media – even if only in the form of excerpts
– shall only be permitted with our express
written consent.
8. The design of this manual is subject to
copyright protection. We do not accept
any liability for any errors or any erroneous
content or printing errors (even in the case
of technical specifications or within graphics
and technical sketches).
9. Our products are in compliance with
all technical guidelines, electrical and
telecommunications regulations applicable
in Germany, the EU and the USA.
Scope of
delivery
1 x I/O Door Controller
1 x Network Cable
1 x Power supply unit (mains adaptor) with four country-
specific adaptors (110 - 240 V AC to 15 V DC)
1 x DIN-Rail adapter
1 x Drilling template
1 x Small parts
1 x Installation manual
Approvals CE, FCC, UL, RoHS, IP50
Weather-proof No
Weight 174 g
EAN 4260423860346
10. Our products and also the components
contained therein (ICs, software, etc.)
may only be used for civilian non-military
purposes.
Data privacy and data security
1. For maximum security, the device uses the
same encryption technologies as are used
in online banking. For your security, no port
forwarding or DynDNS is used either.
2. The data centre location for remote access
over the Internet by means of an App is
obligatory in the EU if the determined
Internet IP-Address location of the device is
within the EU. The data centre is operated
in line with the most stringent security
standards.
3. Video, audio and any other surveillance
methods can be regulated by laws that vary
from country to country. Check the laws in
your local region before installing and using
this device for surveillance purposes.
If the device is a door-, indoor station or camera:
• In many countries video and voice signal
may only be transmitted once a visitor has
rung the bell (data privacy, configurable in
the App).
• Please carry out the mounting in such a
way that the detection range of the camera
limits the device exclusively to the immediate
entrance area.

18
• The device may come with a visitor history and
motion sensor. You can activate/deactivate
this function if required.
If necessary, indicate the presence of the device
in a suitable place and in a suitable form.
Please observe any relevant country-specific
statutory regulations concerning the use of
surveillance components and surveillance
cameras applicable at the installation site.
Check with the property owner and your house
community if you are allowed to install and use
this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or
miss-configuration of this product, including
the unauthorized opening of a door.
Bird Home Automation cannot be held
responsible for damages caused by improper
existing installations or improper installation.
Software and operating system’s updates
(so-called “firmware updates”) are generally
automatically installed on the products of
Bird Home Automation GmbH via Internet,
if technically possible. Automatic firmware
updates keep the products‘ software up to
date so that they always work reliably, safely
and efficiently. Through further development,
features can be added, extended or slightly
changed. Major changes or limitations to
existing features will generally occur if Bird
Home Automation GmbH deems it necessary
(e.g. for data protection, data security or
stability reasons, or to keep them up to date).
When a firmware update is available, Bird
Home Automation GmbH‘s servers generally
automatically distribute it to all compatible
products connected to the Internet or Bird
Home Automation GmbH‘s servers. This process
is gradual and can take several weeks. As soon
as a product receives a firmware update, the
system will be installed and will restart by itself.
Installed firmware updates cannot be undone.
Since the products and software of Bird Home
Automation GmbH are not explicitly customer-
specific products, a customer cannot deny an
automatic update if the product is connected
to the Internet or to the Bird Home Automation
GmbH’s server.
Instructions for disposal
Do not dispose of the device with regular
domestic waste. Electronic equipment must
be disposed e.g. at local collection points for
waste electronic equipment in compliance with
the Waste Electrical and Electronic Equipment
Directive.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: [email protected]
It is possible that these manual still contains
typographical errors or printing errors.The
information in this manual will be checked
regularly and corrections will be made in the
next version. We accept no liability for errors
of a technical or printing nature and their
consequences.

DEUTSCH
19
INSTALLATIONSANLEITUNG
Lesen Sie diese Anleitung sorgfältig, bevor Sie die Komponenten in Betrieb
nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf!
Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben
Sie auch diese Bedienungsanleitung.
Die stets aktuelle Version der Installationsanleitung finden Sie unter
www.doorbird.com/de/support
Zur Vereinfachung der Begriffe verwenden wir „Gerät“ für das Produkt „IP E/A
Tür Controller“ sowie „mobiles Endgerät“ für ein Smartphone/Tablet.
Haftung
Die Erstellung dieses Dokuments wurde sorgfältig vorbereitet. Bitte infor-
mieren Sie Bird Home Automation GmbH über etwaige Ungenauigkeiten
oder Unterlassungen. Bird Home Automation GmbH kann nicht für tech-
nische oder typografische Fehler verantwortlich gemacht werden und behält
sich das Recht vor, Änderungen an dem Produkt und den Handbüchern
ohne vorherige Ankündigung vorzunehmen. Bird Home Automation GmbH
übernimmt keinerlei Garantie in Bezug auf das in diesem Dokument ent-
haltene Material, einschließlich, aber nicht beschränkt auf die implizierten
Garantien der Marktgängigkeit und Eignung für einen bestimmten Zweck.
Bird Home Automation GmbH haftet nicht für Neben- oder Folgeschäden im
Zusammenhang mit der Bereitstellung, Durchführung oder Verwendung dieses
Materials. Das Gerät darf nur für den vorgesehenen Zweck verwendet werden.
Gerätemodifikationen
Dieses Gerät muss in Übereinstimmung mit den Anweisungen in der
Installationsanleitung installiert und verwendet werden. Dieses Gerät ent-
hält keine vom Benutzer zu wartenden Komponenten. Durch unbefugte
Gerätemodifikationen oder Änderungen erlöschen alle anwendbaren
Zertifizierungen und Zulassungen.
Verwendete Symbole
Achtung: Weist auf eine gefährliche Situation hin, die, falls nicht
verhindert, zum Tod oder schweren Verletzungen führt.
Warnung: Weist auf eine gefährliche
Situation hin, welche, falls nicht verhindert, zum Tod oder schweren
Verletzungen führen kann.
Vorsicht: Weist auf eine gefährliche Situation hin, welche, falls nicht
verhindert, zu geringfügiger oder mäßiger Verletzung führen kann.

20
Gefahrenhinweise
Hazard information
• Mounting, installation and servicing work on electrical devices may only
be performed by a qualified eletrician. Failure to observe this regulation
could result in the risk of serious damage to health or fatal injury due to
electric shocks.
• Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must be
pulled out if a hazard occurs.
• For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.
• Because of electrostatic charging, direct contact with the circuit board
can result in destruction of the device. Direct contact with the circuit
board must therefore be avoided at any time.
• Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
• Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have the
device checked by an authorized expert.
• Do not open the device. This voids the warranty of the device. The device
does not contain any parts that can be maintained by the user. In the
event of an error, please have the device checked by an authorized
expert.
• For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized
change and/or modification of the device is not permitted.
• The device is not a toy; do not allow children to play with it. Do not leave
WARNUNG
NOTICE Bitte beachten: Weist auf eine gefährliche Situation hin, welche, falls
nicht verhindert, zu Sachschäden führen kann.
Wichtig: Weist auf wichtige Informationen hin, die den richtigen
Betrieb des Produkts gewährleisten.
Hinweis: Weist auf nützliche Informationen hin, die die optimale
Verwendung des Geräts unterstützen.