DoorBird A1091 Series User manual

VERSION ., MIN. HW .
Page 2-13
Installation Manual
Gigabit PoE-Injector
A1091 Series
Seite 14-27
Installationsanleitung
Gigabit PoE-Injektor
A1091 Serie
A1091

2
INSTALLATION MANUAL
Read these instructions carefully before starting to use any components.
Keep the manual so you can refer to it at a later date if required. If you hand
over the device to other persons for use, please hand over the operating
manual as well.
You can always find the most up-to-date version of the installation manual
on www.doorbird.com/support
To make things easier we use the term “device” for the product “DoorBird
Gigabit PoE-Injector A1091”.
Liability
Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions.
Bird Home Automation GmbH cannot be held responsible for any technical
or typographical errors and reserves the right to make changes to the product
and manuals without prior notice. Bird Home Automation GmbH makes no
warranty of any kind with regard to the content of this document, including,
but not limited to, the implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH shall neither be liable
nor responsible for incidental or consequential damages in connection with
the furnishing, performance or use of this material. This product is only to
be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no
components that require service by the user. Unauthorized equipment
changes or modifications will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Caution: Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Danger: Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Warning: Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

3
ENGLISH
3
Notice: Indicates a situation which, if not avoided, could result
in damage to property.
Note: Indicates useful information which helps in getting the
most out of the product.
NOTICE
Hazard information
Mounting, installation and servicing work on electrical devices may
only be performed by a qualified eletrician. Failure to observe this
regulation could result in the risk of serious damage to health or fatal
injury due to electric shocks.
Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must
be pulled out if a hazard occurs.
For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.
Because of electrostatic charging, direct contact with the circuit
board can result in destruction of the device. Direct contact with the
circuit board must therefore be avoided at any time.
Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have
the device checked by an authorized expert.
Do not open the device. This voids the warranty of the device.
The device does not contain any parts that can be maintained by the
user. In the event of an error, please have the device checked by an
authorized expert.
WARNING
Important: Indicates significant information which is essential
for the product to function correctly.

44
For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized
change and/or modification of the device is not permitted.
The device is not a toy; do not allow children to play with it. Do not
leave packaging material lying around. Plastic films/bags, pieces of
polystyrene, etc. can be dangerous in the hands of a child.
Always lay cables in such a way that they do not become a risk to
people and domestic animals.
Voltage is applied to parts within the equipment. Do not touch any
parts that are not associated with the installation, wiring, or connection.
Electric shock could result.
On devices which are not marked as weather-proof: Keep the device
away from water or any other liquid.
Do not install or make any wire terminations while power supply is
plugged in. It can cause eletric shock or damage to the device.
Before turning on power, make sure wires are not crossed or shorted.
If not, fire or eletric shock could result.
High voltage may be present internally. Do not open the device.
Electric shock could result.
The device is not of explosion-proof. Do not install or use near gases
or flammable materials. Fire or explosion could result.
Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power
supply to the device.
Do not connect any terminal on the device to an AC power line. Fire
or electric shock could result.
Keep AC cord from being marred or crushed. If the AC cord is fractured,
fire or electric shock could result.
Do not plug or unplug with wet hands. Electric shock could result.
WARNING

5
ENGLISH
5
Do not put any metal or flammable material into the device.
Fire, electric shock, or device trouble could result.
Existing wiring such as chime wiring, etc. may contain high voltage
AC electricity. Damage to the device or electric shock could result.
Wiring and installation must be done by a qualified eletrician.
When mounting the device on a wall or ceiling, install the device in
a convenient location, but not where it could be jarred or bumped.
Injury could result.
On devices with ground terminals, connect to an earth ground.
Otherwise fire or malfunction could result.
On devices with plastic or real glass, do not put high pressure on
the glass. If fractured, injury could result.
On devices with LCD, if LCD is punctured, do not allow contact
with the liquid crystal inside. Injury could result. If necessary, gargle
your mouth and clean your eyes or skin with clear water for at least
15 minutes and consult your doctor.
Do not put anything on the device or cover the device with cloth,
silicone, glue, coating, separate covering etc. Fire or device issues
could result.
Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.
- Places under direct sunlight or places near heating equipment that
varies in temperature.
- Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
- Places subject to moisture and humidity extremes, such as bathrooms,
cellars, greenhouses, etc.
- Places where the temperature is very low, such as inside a refrigerated
area or in front of an air conditioner.
- Places subject to steam or smoke (e.g. near heating or cooking surfaces).
- Where noise generating devices such as dimmer switches or inverter
electrical appliances are closeby.
- Locations subject to frequent vibration or impact.

66
On devices with intercom, be sure to perform a call test with low
audio volume on both intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.
If the device does not operate properly, unplug the power supply.
All devices which are not marked as weather-proof are designed for
indoor use only. Do not use outdoor.
On devices which are marked weather-proof: Do not spray with
high-pressure water. Device issues could result.
We do not assume any liability for damage to property or personal
injury caused by improper use or the failure to observe the hazard
information. In such cases, any claim under warranty ceases.
For consequential damages, we assume no liability!
WARNING
Safety instructions
The device shall be used in compliance with local laws and regulations.
Store the device in a dry and ventilated environment.
Avoid exposing the device to shocks or heavy pressure.
Do not install the device on unstable brackets, surfaces or walls.
Make sure the material is strong enough to support the weight of
the device.
Use only applicable tools when installing the device. Using excessive
force with tools could cause damage to the device.
Do not use chemicals, caustic agents, or aerosol cleaners.
Use a clean dry cloth for cleaning.
Use only accessories that comply with technical specification of the
device. These can be provided by Bird Home Automation GmbH.
Use only spare parts provided by or recommended by Bird Home
Automation GmbH.
Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.
NOTICE

7
ENGLISH
7
Keep the device more than 1 m (3.3') away from microwave, radio, TV,
wireless router and any other wireless devices.
On devices with intercom or built-in speaker or built-in microphone
or signal transmission functions, keep the wires more than 30 cm (12'')
away from AC 100-240 V wiring. AC induced noise and/or device
malfunction could result.
Install the device in an area that will be accessible for future inspections,
repairs and maintenance.
If the device is used close to a cellular phone, the device may malfunction.
The device can be damaged if dropped. Handle with care.
The device turns inoperative during power failure.
On devices with intercom or built-in speaker or built-in microphone,
in areas where cellular or Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio frequency interference.
On devices with LCD screen, it must be noted in advance that the LCD
panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its picture elements always lit
or not lit at all. This is not considered a device malfunction.
On devices with intercom, due to the environmental sound around
the device, it may hinder smooth communication, but this is not a
malfunction.
On devices with Username/Password, the Username/Password to
access the device is the customer's responsibility. Make sure to use
password that cannot be easily guessed by a third party.
We recommend that you change the Password on a regular basis.
We will, under no circumstances, be liable for damage that occurs due
to failures in power supply, network equipment or terminal devices;
failures due to Internet providers and cellular network providers;
failures such as disconnected lines and other losses in communication,
which makes it impossible to provide this service as well as in any way
delay this service due to any other causes outside of our responsibility;
or if an error or missing data occurs during transmission.

8
COMPONENTS
Warranty Information
For information about the device warranty, see www.doorbird.com/warranty
Transportation
When transporting the device, use the original packaging or
equivalent to prevent damage to the device.
NOTICE
1x Drilling template
1x RJ45 network cable
(300 cm)
1x DIN-Rail adapter 2x Phillips countersunk
head screws and dowels
1x Quickstart guide
with Digital Passport
1x Installation manual1x Device
1x Power supply unit (mains adaptor)
with four country-specific adaptors

9
ENGLISH
LAN IN
RJ45 jack to connect a standard
Network cable Cat.5 or better,
coming from the Internet Router.
PWR
Power Input Diagnostic-LED.
15 VDC IN
Power supply (Input, 15 VDC).
2
3
6
1
4
5
POE
PoE Diagnostic-LED (Output).
POE + DATA OUT
RJ45 jack to connect a standard
Network cable Cat.5 or better,
going to the product to supply
with PoE and network data.
Screw holes
Two screw holes for mounting the
device on a wall or ceiling.
DEVICE
2x Phillips countersunk
head screws and dowels
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support.
Each individual step of the installation is clearly documented in the videos.
INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird

10
App. The user experience is only as good as your network speed, network
stability and quality of your network components, such as your Internet router
and WiFi access points or WiFi repeaters. Please also make sure that your net-
work components are not older than two years, have been manufactured by a
well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, for example that
the performance of audio and video is poor or push notifications are delayed
or do not arrive on your smartphone or tablet at all.
Requirements:
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11 b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the door
station, door chime, electric door opener, power supply unit, PoE-Switch /
PoE-Injector etc.
STEP 2: DETERMINING THE ASSEMBLY LOCATION
The device is IP50 certified (not water-proof). Please make sure to put the
device into an appropriate housing if you want to use it outdoors.
The network cable between the device and the product to supply with PoE
and network data can have maximum length of 80 meters/262 feet.
STEP 3: DOWELS AND SCREWS
You can mount the device permanently on a wall or ceiling using appropriate
screws. Please skip this step if you do not want to mount the device permanently.
Press the drilling template of the device against the wall or ceiling at the
desired installation site and mark the boreholes with a pencil. Remove the
drilling template again. Ensure that no cables are to be found in the wall
or ceiling behind the boreholes.
If the wall of the house is not made of wood, you should drill dowel holes
5 mm in diameter in the wall according to the drilling template and then place
the dowels provided into the boreholes. If the wall of the house is made of
wood, dowels are normally not required. There are special dowels for assembling
the device on an insulating wall, e.g. Fischer insulating dowels. Please check with
your insulating material manufacturer regarding which dowels they recommend.

11
ENGLISH
Press the device on the wall or ceiling, so you can see the boreholes in the wall/
ceiling through the screw holes of the device. Use the Phillips countersunk head
screws provided to position it in the dowels or on the wall to fix the device on
the wall/ceiling.
STEP 4: INSTALLATION
Connect the network cable coming from your Internet to the RJ45 jack “LAN
IN” of the device. Then connect a second network cable to the RJ45 jack
“POE + DATA OUT” of the device. Connect the spare end of the network cable
connected to the RJ45 jack “POE + DATA OUT” to the product you would
like to establish a PoE and network data connection with, e.g. a DoorBird IP
Video Door Station, DoorBird 2-Wire Ethernet PoE Converter (Sender) or an
IP Camera.
A Cat.5 network cable with RJ45 plug or better must be used to connect to
the “LAN IN” and “POE + DATA OUT” jacks of the device.
Connect the 5.5 mm DC plug of the Power supply unit (mains adaptor)
supplied with the device into the jack “15 VDC IN” of the device. Do not plug
the Power supply unit itself into a wall socket yet.
STEP 5: ACTIVATING THE DEVICES
Switch on the power leading to the assembly location again. Then plug the
Power supply unit (mains adaptor) of the device into a wall socket.
The “PWR” and the “POE” Diagnostic-LEDs of the device should be active
now. Please check the network cable connections and the power supply if
the Diagnostic-LEDs are not active.
DIAGNOSTIC-LEDS
You can check if the power supply and PoE supply of the device are working
by checking the Diagnostic-LEDs. The Diagnostic-LEDs should be active.

12
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird
Home Automation GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh,
iPad, Multi-Touch, iOS, iPhone and iPod touch are
trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks
of Google, Inc.
4. The Bluetooth® word mark and logos are regis-
tered trademarks of Bluetooth SIG, Inc.
5. All other company and product names may
be trademarks of the respective companies with
which they are associated.
6. We reserve the right to make changes to our
products in the interests of technical advance-
ment. The products shown may also look different
from the products supplied based on ongoing
enhancement.
7. Reproducing or using texts, illustrations and
photos from this instruction manual in any media
– even if only in the form of excerpts – shall only be
permitted with our express written consent.
8. The design of this manual is subject to copy-
right protection. We do not accept any liability for
any errors or any erroneous content or printing
errors (even in the case of technical specifications
or within graphics and technical sketches).
9. Our products are in compliance with all techni-
cal guidelines, electrical and telecommunications
regulations applicable in Germany, the EU and
the USA.
Data privacy and data security
1. For maximum security, the device uses the same
encryption technologies as are used in online
banking. For your security, no port forwarding or
DynDNS is used either.
2. The data centre location for remote access over
the Internet by means of an App is obligatory in
the EU if the determined Internet IP-Address
location of the device is within the EU. The data
centre is operated in line with the most stringent
security standards.
3. Video, audio and any other surveillance methods
can be regulated by laws that vary from country
to country. Check the laws in your local region
before installing and using this device for surveil-
lance purposes.
If the device is a door-, indoor station or camera:
In many countries video and voice signal may
only be transmitted once a visitor has rung the
bell (data privacy, configurable in the App).
Please carry out the mounting in such a way
that the detection range of the camera limits the
device exclusively to the immediate entrance
area.
The device may come with a visitor history and
motion sensor. You can activate/deactivate this
function if required.
If necessary, indicate the presence of the device in
a suitable place and in a suitable form.
Please observe any relevant country-specific
statutory regulations concerning the use of
surveillance components and surveillance cameras
applicable at the installation site.
Check with the property owner and your house
community if you are allowed to install and use
this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or
miss-configuration of this product, including the
unauthorized opening of a door.
Bird Home Automation cannot be held responsible
for damages caused by improper existing installations
or improper installation.
Software and operating system’s updates
(so-called “firmware updates”) are generally
automatically installed on the products of
Bird Home Automation GmbH via Internet, if
technically possible. Automatic firmware updates
keep the products‘ software up to date so that
they always work reliably, safely and efficiently.
Through further development, features can be
added, extended or slightly changed. Major
changes or limitations to existing features will
generally occur if Bird Home Automation GmbH
deems it necessary (e.g. for data protection, data
security or stability reasons, or to keep them up
to date). When a firmware update is available,
Bird Home Automation GmbH‘s servers generally
automatically distribute it to all compatible
products connected to the Internet or Bird
Home Automation GmbH‘s servers. This process
is gradual and can take several weeks. As soon
as a product receives a firmware update, the
system will be installed and will restart by itself.
Installed firmware updates cannot be undone.
Since the products and software of Bird Home
Automation GmbH are not explicitly customer-
specific products, a customer cannot deny an
automatic update if the product is connected
to the Internet or to the Bird Home Automation
GmbH’s server.

13
ENGLISH
Instructions for disposal
Do not dispose of the device with regular domestic
waste. Electronic equipment must be disposed
e.g. at local collection points for waste electronic
equipment in compliance with the Waste Electrical
and Electronic Equipment Directive.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: [email protected]
Other manuals for A1091 Series
2
Table of contents
Other DoorBird Laboratory Equipment manuals
Popular Laboratory Equipment manuals by other brands

Major Science
Major Science MC-0203 instruction manual

Met One
Met One BAM 1020 Operation manuals

caron
caron 7545-1 Preventative Maintenance Kit instructions

Biosan
Biosan Inteliwasher 3D-IW8 User instructions

Cole Parmer
Cole Parmer SPEX 8000M Operation manual

Markes International
Markes International HiSorb Agitator Instructions for use

Hemotherm
Hemotherm 400MR Operation & technical manual

Biuged Laboratory Instruments
Biuged Laboratory Instruments BGD 626 instruction manual

Witeg
Witeg Wisd CF-10 operating manual

Witeg
Witeg Wisd WiseMix RT-10 operating manual

Behncke
Behncke UV matic A20 user manual

Faro
Faro SK07 Series instruction manual