DoorHan APRO 20 User manual

MENAPRO20032009
APRO 20 ENGLISH
The APRO 20 microwave movement detector controls the opening of factory gates and
automatic doors. It works in the K band. It can be installed at a height ranging from 3 to 6
metres and guarantees the surveillance of an area from 3 to 30 square metres .
The device will be automatically activated by moving persons or vehicles within the
controlled perimeter.
APRO 20 has been developed using planar technology, and can be set in mono-
directional (to detect movement either in forward or backward direction) or bi-
directional (activated by movement in both directions). A microprocessor processes the
signals received – generated through a Doppler effect – and sends an OK to the opening
command.
A LED on the front panel indicates that movement has taken place inside the controlled
area.
TECHNICAL DATA
Power voltage 12 – 24 VAC/12 - 30 VDC
Power current max. 50 mA
Operative frequency 9.90 GHz
Output Power (EIRP) d14 dBm
Range 1 – 10 m adjustable
Relay control time 1 – 6 s adjustable
Degree of protection IP 66
Installation height max. 6 m
Detectable speed 0.1 m/s minimum
Relay contact 1A - 24 VAC/DC
Vertical directionality 0-60°
Horizontal directionality +/- 45°
Operating temperature - 20 °C to + 50 °C
Dimensions/weight 160x95x110 mm / 500 g
Warranty 24 months
NOTE: A SELV power source must be used (certified power supply unit or safety transformer) in
compliance with CEI EN 41003:1993 standard.
We hereby declare that Apro20 complies with the essential requirements of Directive 99/05/EC (R&TTE)
harmonised radio standard pursuant to Art. 3.2 of Italian Law No. 269 dated 9.5.2001: EN300440-2 V 1.1.2
Via Cagliari, 19 - Tel. [phone]
10153 Torino - ITALIA

MENAPRO20032009
APRO 20 ENGLISH
SETTING FOR OPERATION
The APRO 20 movement detector can be configured in mono direction mode (one
direction only) or in bi directional mode (in both directions).
Remove the rubber plug from the lower section of the detector (Fig. 1-A) and set the
required function through the dip-switch (Fig. 1-B), choosing from the possibilities
indicated in the table:
DSW1 DSW2 DSW4 SENSITIVITY CONDITION
OFF - ON Low Movement is detected in both directions
OFF - OFF High Movement is detected in both directions
ON OFF ON Low Approach to the sensor is detected
ON OFF OFF High Approach to the sensor is detected
ON ON ON Low Movement away from the sensor is detected
ON ON OFF High Movement away from the sensor is detected
ASSEMBLY AND ORIENTATION
APRO 20 can be installed at the centre of the door to be controlled or on the side, on
non-vibrating structures (walls or ceiling) and at a maximum height of 6 m. Use the
template supplied to prepare the holes.
Fasten the device using the prepared holes, remove the lower cover (Fig. 2-A) and
loosen the screw that blocks the detector orientation. Direct the detector toward the area
to be controlled and lock in that position.
For correct operation, do not install APRO 20 :
- facing the moving parts of the door
- facing fluorescent lights (minimum distance 2m)
- facing areas where rain could provoke water fluxes
These conditions could activate the device and cause the unwanted opening of the door.
ELECTRICAL CONNECTIONS
Connect the pre-wired cable as indicated in table 1 then power the detector.
Via Cagliari, 19 - Tel. [phone]
10153 Torino - ITALIA

MENAPRO20032009
APRO 20 ENGLISH
The LED on the detector front panel (Fig. 2-B) will indicate the detection of a movement,
for all the time the relay is excited.
A E F B B A
Fig.1 Fig.2
Wire colour Description
Red 12-24 V AC/DC
Black 12-24 V AC/DC
Green COM relay contact
Brown NO contact (when device is not powered)
Blue NC contact (when device is not powered)
Tab.1
RELAY CONTACT SETTING
APRO 20 has a relay with switching contact.
According to the setting of the dip-switch 3 (Fig. 1-B) in the lower section of the detector,
the combinations described in table 2 can be obtained.
These conditions are valid when the device is powered.
Via Cagliari, 19 - Tel. [phone]
10153 Torino - ITALIA

MENAPRO20032009
APRO 20 ENGLISH
DSW3 ON
(Normal operation)
DSW3 OFF
(Positive safety)
Tab.2
SETTING OF DETECTION RANGE
It is possible to define the controlled area by changing the inclination of the detector and
the position of dip-switch 4 (Fig. 3). With trimmer TR1, located on the lower section of the
detector (Fig. 1-F), the regulation can be optimised to activate detection only for the
desired area.
AS: high sensitivity
BS: low sensitivity
Dimensions in metres
Fig. 3
REGULATION OF CONTACT DURATION
The trimmer TR2 on the lower section of the detector (Fig. 1-E) can be used to set the
desired duration of the electric contact, which can vary from 1 – 6 seconds.
BS (Incl. 60°)
AS (Incl. 45°)
Via Cagliari, 19 - Tel. [phone]
10153 Torino - ITALIA