Dorel Baby Relax DA6564 User manual

Lot number:
NOTE:
_______ / _______ / _______
THIS INSTRUCTION BOOKLET
_____________________________________
(TAKEN FROM CARTON)
CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
Date of purchase:
DOREL ASIA
Model No:
DA6564 (WHITE & GRAY)
3 IN 1 CRIB
0-65857-16619-4
UPC CODE:
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel #: [phone]
E-Mail: [email protected]
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

*Failure to follow these warnings and assembly instructions could result in serious injury or death.
*Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
*
*
*Stop using crib when child begins to climb out or reaches the height of 35 inches (89 cm).
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
* DO NOT place crib near window where cords from blinds or drapes may strangle a child.
*Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
*To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose
fasteners.
*If refinishing, use a non-toxic finish specified for children's products.
*When child is able to pull to standing position, set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps for climbing out.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
*Replace teething rail if damaged or loose (if teething rail is provided for this model).
*Follow warnings on all products in a crib.
*CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY
51-5/8 INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM)
BUT NOT EXCEEDING 6 INCHES (15CM).
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*The TODDLER BED or DAY BED is not intended for children under 15 months of age or over 50 pounds
(22.7kgs)
*If guardrails are used as the mattress containment means, guardrail(s) provided must be used to avoid the
formation of a gap between the mattress and the bed that could cause an entrapment (when product is
used as a TODDLER BED or DAY BED).
*
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts or
sharp edges before assembly and frequently during use. Securely tighten loose bolts and other fasteners.
DO NOT use crib if any parts are missing, damaged or broken. Contact a customer service representative
at 1-800-295-1980 for replacement parts and instructional literature if needed. DO NOT substitute parts.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
The mattress intended for use on the bed shall be a full-size crib mattress having minimum dimensions of
51-5/8 in. (1310 mm) in length and 27-1/4 in. (690 mm) in width with a minimum thickness of 4 in. (100 mm)
and not exceeding 6 in. (150 mm).
WARNING
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service
representative first! CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model
number, color and a detailed description of the part.
Montreal, Quebec
Canada, H1G 3L1
E-MAIL: [email protected]

* Ensure all parts and components are present before beginning assembly.
* Assemble on a soft, smooth surface to prevent damage to product finish.
* Phillips head screw driver is not included.
*
DO NOT use power tools.
* CAUTION: Adult assembly required.
* Assembly will require two people.
* Estimated assembly time: 30 minutes.
Check bolts/screws periodically and tighten them if necessary.
Dorel Asia warrants its product to be free from defects in material and workmanship and agrees to
remedy any such defect. This warranty covers 1 year from the date of original purchase. This
warranty is valid only upon presentation of proof of purchase. This is solely limited to the repair or
replacement of defective furniture components and no assembly labor is included. This warranty
does not apply to any product which has been improperly assembled, subjected to misuse or abuse
or which has been altered or repaired in any way. This warranty gives you specific legal rights and
you may also have other rights which vary from State to State.
WARNING: Should this product become
damaged, and/or components are broken or
missing, DO NOT USE.
NOTES
CARE AND CLEANING
Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage finish.
Excessive exposure to sunlight and extreme changes in temperature and moisture can damage
wood furniture.
MAINTENANCE
LIMITED WARRANTY

HARDWARE LIST
1 2
3 4
5 6
7
BOLT
2 PCS
3 IN 1 CRIB
DA6564
MATTRESS SUPPORT BOLT
16 PCS
BOLT
8 PCS
BOLT
8 PCS
ALLEN KEY
1 PC
BARREL NUT
8 PCS
Ø1/4" X 10mm X 13mm
Ø1/4" X 13mm X 60mm
Ø1/4" X 13mm X 44mm
Ø1/4" X 13mm X 78mm
Ø1/4" X 13mm X 18mm
Ø1/4" X 13mm X 55mm
BOLT
2 PCS

PARTS LIST
A1 A2 B1
B2 C D
E F G
H
RIGHT FRONT POST
1 PC
3 IN 1 CRIB
DA6564
RIGHT SIDE PANEL
1 PC
LEFT BACK POST
1 PC
LEFT FRONT POST
1 PC
MATTRESS SUPPORT
1 PC
FRONT RAIL
1 PC
RIGHT BACK POST
1 PC
BACK PANEL
1 PC
LEFT SIDE PANEL
1 PC
FRONT PANEL
1 PC

NOTE: When inserting bolts, turn clockwise until tight. Then loosen
1/2 - 3/4 of a turn. After crib is completely assembled, return to each
bolt and tighten. Use wax or soap on all bolts to facilitate assembly.
3 IN 1 CRIB
DA6564
CRIB ASSEMBLY INSTRUCTION

STEP 1
Attach left front post (A1) & left back post (B1) to left side panel (D) with bolts (1) as shown.
Use Allen Key (5) to tighten all bolts (1).
3 IN 1 CRIB
DA6564
①

STEP 2
Attach right front post (A2) & right back post (B2) to right side panel (E) with bolts (1) as shown.
Use Allen Key (5) to tighten all bolts (1).
3 IN 1 CRIB
DA6564
①

STEP 3
Attach the back panel (C) to left back post (B1) of left side panel (D) with bolts (2) and
barrel nuts (6) as shown.
Use Allen Key (5) to tighten all bolts (2).
Repeat this step to attach back panel (C) to right back post (B2) of right side panel (E).
3 IN 1 CRIB
DA6564
⑥②
INSIDE
NOTE:
The lower rails of side panels
(D & E)
are labeled "INSIDE." To ensure
proper assembly, the side panels must
be attached so that the INSIDE label
face inside the crib.

STEP 4
3 IN 1 CRIB
DA6564
Attach mattress support (H) to the posts with mattress support bolts (3).
Use Allen key (5) to tighten the bolts (3).
INCORRECT-
Raised edge
should face
down -this photo
shows mattress
support is
upside down.
INCORRECT-
Tabs on corners
of mattress
support should
point up.
CORRECT
*Tabs to point UP.
*Flat surface of mattress
support to face up - mattress
must sit on flat surface.

NOTE: The above photos and drawings showing how to properly attach the
mattress support are for reference only. Crib styles and colors will vary.
③

STEP 5
Attach front rail (G) to left front post (A1) of left side panel (D) with bolt (2) and barrel nut (6).
Use Allen key (5) to ti hten the bolt (2).
Repeat this step to attach front rail (G) to ri ht front post (A2) of ri ht side panel (E).
3 IN 1 CRIB
DA6564
⑥
②
11

STEP 6
Attach front panel (F) to left front post (A1) of left side panel (D) with bolts (2)（4） and barrel
nut (6). Use Allen key ( ) to tighten the bolts (2)（4）.
Repeat this step to attach front panel (F) to right front post (A2) of right side panel (E).
3 IN 1 CRIB
DA6564
④②
⑥
12

STEP 7
Fasten the front panel (F) and front rail (G) with bolts (7).
Use Allen key (5) to tighten the bolts (7).
3 IN 1 CRIB
DA6564
⑦
NOTE:
DO NOT throw away this
instruction manual. Use the
crib pouch attached to the
mattress support to store this
manual for future use.

WARNINGS:
*ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY
51-5/8 INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES
(10CM) BUT NOT EXCEEDING 6 INCHES (15CM).
*The day bed is not intended for children under 15 months of age or over 50 lbs (22.7 kgs).
STEP 1: Unscrew the bolts (7) underneath the front rail (G) with Allen Key (5).
STEP 2: Detach the front panel (F) from the posts (A1 & A2) with Allen Key (5).
STEP 3: If mattress support (H) is not in the lowest position, unscrew bolts (3) from left & right
posts (A1, A2, B1 & B2) and move to the lowest position.
STEP 4: Ensure all bolts are tightly secured.
STEP 1: Follow steps 1 to 4 of the crib assembly instructions.
3 IN 1 CRIB
DA6564
DAY BED ASSEMBLY: STARTING FROM CRIB
DAY BED ASSEMBLY: STARTING FROM SCRATCH

3 IN 1 CRIB
DA6564
FULL SIZE BED ASSEMBLY INSTRUCTION
(HEADBOARD ONLY)
NOTE: FULL SIZE CONVERSION RAILS ARE NOT INCLUDED. DIAGRAMS ARE FOR
REFERENCE ONLY. BED RAILS MAY DIFFER FROM ILLUSTRATION.
DIAGRAM 2
IMPORTANT: STORE ALL EXTRA PARTS THAT YOU ARE NOT USING FOR POSSIBLE
FUTURE USE AS YOU MAY WISH TO CONVERT AGAIN. ALWAYS STORE THE ASSEMBLY
INSTRUCTIONS IN THE POUCH ATTACHED TO THE MATTRESS SUPPORT (H).
STEP 1
Attach the full size conversion rails (not included) to the assembled headboard (B1,B2 & C).
DIAGRAM 1

That's it ! You've finished assembling your 3 in 1 convertible crib!
3 IN 1 CRIB
DA6564
CAUTION: This unit is intended for use only with the
products and/or maximum weights indicated. Use with other
products and/or products heavier than the maximum weights
indicated may result in instability or cause possible injury.
ANY MATTRESS USED IN THIS
CRIB MUST BE AT LEAST 27-1/4
INCHES BY 51-5/8 INCHES (69CM
BY 131CM) WITH A MINIMUM
THICKNESS OF 4 INCHES (10CM)
BUT NOT EXCEEDING 6 INCHES
(15CM).
Stop using crib when child begins
to climb out or reaches the height
of 35 inches (89 cm).
Maximum weight not to exceed 50
pounds when used as a crib.
The DAY BED is not intended for
children under 15 months of age or
over 50 pounds (22.7 kgs).
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel #: [phone]
E-Mail: [email protected]
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

MODEL #: DA6564
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING
NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
Request Date:
Name:
Shipping Address:
Street & Number:
City & State:
Zip Code:
Day Time Phone Number:
(including area code)
Date & Place of Purchase:
Part(s) description and quantity: (Please be sure to list model number or SKN number)
Customer Service Representative Mailing Address:
Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, QC, Canada, H1G 3L1
Customer Service
Customer Service Phone Number 1-800-295-1980
Email: [email protected]
Customer Service Fax Number 514-353-7819