Dorset trovan LID-WAP Guide

1
LID-
WAP:
RFID
module
for PSION
Work
About
Pro
Document version: 2.0
Da
te:
March
6
th
200
9
Mountingmanual trovan
trovantrovan
trovan
®
This manual is intended for those who will mount the LID-WAP into the
WorkAbout Pro them selves. Follow this manual step by step.
DORSET IDENTIFICATION B.V. is NOT responsible for ANY
damage caused by LID-WAP module or its assembly.
Warning: Always take sufficient countermeasures for ESD.
Step 1: Checking the package content.
The LID-WAP package must contain the following parts:
1x LID-WAP pcb including antenna, wrapped in antistatic foil.
2x tie-wraps.
4x M2 screw.
Step 2: Removing the battery pack.
Before you open the WorkAbout Pro, it is necessary to remove the battery pack. This is done
for safety reasons.
2.1 Take the stylus out of the WorkAbout Pro.
2.2 Left turn the lock screws of the battery
compartment using the back of the stylus.
2.3 Remove the lid and remove the battery-pack.
Step 3: Opening the WorkAbout Pro.
3.1 Unscrew the 4 screws on the front of the
WorkAbout Pro.
3.2 Remove the cap and move the
switch that is located on the right
side into the “off position”. If there is
no Wifi module is installed please go
to step 3.5.
3.3 Unscrew the Wifi cap (if installed).
3.4 Remove Wifi module and place the
adhesive foam pad. (see picture for
the correct position).
2.2
2.1
2.3
3.2
3.1
3.3
3.4

2
3.5 Unscrew the 6 screws on the backside of
the WorkAbout Pro.
3.6 Remove the backside of the WorkAbout
Pro. If a barcode scanner is installed, let it
rest on the battery compartment.
Step 4: Inserting the LID-WAP.
4.1 Remove the antistatic foil from the LID-WAP.
4.2 Peel off the antistatic sticker on the backside of the
LID-WAP to free the antenna.
4.3 Insert the antenna through the frame of the LID-
WAP.
4.4 Make sure that the area where the LidWAP has to
be placed is free of any band cables. Put the
LID-WAP into place and gently press the
connector into the mainboard of the
WorkAbout Pro by pressing on both sides of
the connector. If a wifi module was installed,
please remove the protection label from the
white foam sticker and put the module back
into place.
4.5 Peel off the protection label from the white
foam sticker.
4.6 Insert the tie-wraps into the holes on both
sides of the foam pad. Put the head of the
tie-wraps close to the PCB (see picture).
Otherwise you could experience difficulties
when putting back the end-cap.
4.7 Press the antenna into place carefully and
tighten the tie-wraps. Once tightened, cut off the remaining
length of the tie-wraps.
Use the 4 screws to secure the LID-WAP into the WorkAbout Pro.
3.5
3.6
4.2
4.3
4.4
4.5
4.7
4.6
4.8

3
Step 5: Closing the WorkAbout Pro.
5.1 Put the back cover/barcode-scanner
back into its position and tighten the
6 screws.
5.2 Move back the switch into the “on”
position.
5.3 If a wifi card is installed, do not place
back the wifi cap.
5.4 Put the end-cap back into place and tighten the 4 screws.
Step 6: Re-inserting the battery pack.
6.1 Insert the battery pack and replace the lid.
6.2 Right turn the lock screws of the battery
compartment using the back of the stylus.
The module is now completely mounted, if necessary you can download a demo application +
manual from our website: www.dorset.nu
5.1
6.1
6.2
5.2
5.4
3.4