DOSKO 337-13H User manual

20195 South Diamond Lake Road, Suite 100 • Rogers, MN 55374 • USA (Toll-Free): 866-298-3659 • International: [phone] • www.dosko.com
20195 South Diamond Lake Road, Suite 100 • Rogers, MN 55374 • USA (Toll-Free): 866-298-3659 • International: [phone] • www.dosko.com
Models 337-13H & 357-13HE
BEFORE GRINDING STUMPS
• Be aware of all underground utilities before grinding stump.
STARTING GRINDER
• Press down on handle bar so that cutter wheel is off the
ground.
• Pull out on-off switch (located on control panel).
• Turn switch to “On” position (located on engine).
• Pull choke if engine is cold (located on engine).
• Set throttle about ¼open (located on engine).
• Engage operator presence handle by pushing handle
(small diameter bar) towards “Handle Bar Bow.”
• Recoil: Pull recoil rope to start engine (located on engine).
Electric: Turn key to start engine (located on engine).
• When engine starts —close choke.
GRINDING STUMP
• Push grinder to stump so that the stump is located just in
front of the cutter wheel.
• Using the brake lever —lock the one wheel.
• Pull throttle to full open (located on engine).
• Lower the cutter wheel slowly using a left-to-right motion to
grind the stump.
• Grind stump to desired depth.
• Handle bar may have to be adjusted to accommodate for
height of stump or desired depth. Raise or lower handle bar
to a comfortable safe position.
• Reposition grinder further on stump and begin this process
again.
: CUTTING WHEEL WILL CONTINUE
TO TURN FOR A SHORT PERIOD AFTER ENGINE IS
SHUT OFF.
Operating
Zone
Pin Adjustment
Handle Bar
Discharge Flap
Battery Box
(if equipped with
electric start)
Cutter Wheel
Disc
Control Panel with
On-Off Switch
Operator
Presence
Handle
Cutting
Tooth
Tooth
Pocket
Gas Tank
Engine Throttle
& Choke
Side Discharge
Frame
Adjustable
Brake Lever
Handle Bar Bow
Handle Bar
Item # E786112

Recoil Rope
OPERATING INSTRUCTIONS
Belt Guard
Key Switch
(if equipped with
electric start)
Air Filter
Please reorder as needed. These safety sheets are free of charge. Additional safety sheets are available online for your convenience at www.dosko.com. They are also available by contacting Dosko at 866-298-3659 and requesting Item # E786112. NOTE: Please make sure that your customers sign the back of this safety sheet indicating they have read and understand the operating and safety instructions.
Know Your Dosko:
BEFORE STARTING OR USING THIS MACHINE, READ AND REVIEW THIS SAFETY SHEET! BE AWARE OF ALL POTENTIAL DANGERS,
PROTECT WINDOWS AND VEHICLES FROM POSSIBLE FLYING DEBRIS AND BE AWARE OF ALL NECESSARY SAFETY PRECAUTIONS!
ALWAYS
THINK
SAFETY

20195 South Diamond Lake Road, Suite 100 • Rogers, MN 55374 • USA (Toll-Free): 866-298-3659 • International: [phone] • www.dosko.com
20195 South Diamond Lake Road, Suite 100 • Rogers, MN 55374 • USA (Toll-Free): 866-298-3659 • International: [phone] • www.dosko.com
READ all instructions and decals before starting!
WEAR proper safety clothing; safety glasses,
sturdy footwear, gloves, face shield, etc.!
OPERATE grinder only from operating zone!
NEVER start grinder before checking controls and
brakes!
ALWAYS lock brake before grinding begins!
NEVER allow anyone within 75 feet while grinding!
NEVER leave grinder unattended while running!
NEVER grind anything other than stumps!
ALWAYS be aware of your surroundings!
ALWAYS position machine to protect windows and
vehicles from flying debris!
ALWAYS be prepared for emergencies by having
first-aid supplies and a fire extinguisher!
NEVER operate while guards or shields are removed!
NEVER attempt to override any safety devices!
NEVER use in bad or questionable weather!
ALWAYS shut the machine off if any unusual noise or
vibration occurs!
ALWAYS store machinery and gasoline away from the
reach of any children!
QUESTIONS?Call your authorized Dosko dealer or rental
center, or call Dosko direct at 866-298-3659!
Use this form when renting or loaning the equipment
model(s) indicated on the reverse side of this sheet.
Have the user initial each of the three statements below
and sign acknowledging receipt of this safety sheet.
Remove This Section and Keep For Your Records!
I have been instructed in the use of this stump
grinder, and I fully understand its operations.
All controls have been checked and are in good
working condition.
I have been instructed about the dangers of this
machine if not used properly. I am aware of all
safety procedures and I accept full responsibility.
I agree to “hold harmless” the manufacturer,
dealer, rental yard owner, or anyone connected
with Dosko.
Dosko Stump Grinder Model (please circle):
337-13H 357-13HE
Honda Honda
Serial Number_________________________________
Name________________________________________
Company_____________________________________
Address______________________________________
City _________________________________________
State ____________________________ Zip_________
Telephone (_____) _____________________________
Signature_____________________________________
Date_________________________________________
Dealer/Agent Name ____________________________
Dlr/Agt Signature ______________________________
Date_________________________________________
Item # E786112
TOWING INSTRUCTIONS
There are certain legal road requirements for various
states. It is the responsibility of the owner or user to be
aware of these laws; and to obey them. For example,
there may be lighting or licensing requirements.
1. Position tow bar into socket, then insert lock
pin with safety clip.
2. Connect grinder to vehicle using 2” tow ball.
(Be sure that proper size ball is used to match
coupler size.)
3. Be sure the tow hitch socket is closed/secured
to tow ball and pinned.
4. Be sure that the safety chain is properly
hooked to the vehicle and stump grinder by
using the coupling links.
5. Be sure that wheels are fastened tightly and
that tire condition and air pressures meet the
manufacturer’s specifications listed on the tire.
6. Make sure brake is released.
NEVER attempt to back up unit when in the tow position
using towing vehicle.
NEVER tow exceeding 45 MPH.
While your Dosko stump grinder is very easy to use,
and is safety-engineered, there are some simple rules
and procedures which MUST be followed to ensure your
safety, and to ensure the machine’s best performance.
Please take a few moments to review these rules and
procedures:
Thank You For Choosing

ALWAYS
THINK
SAFETY
« DEALER INFORMATION »