Get S tart
Features
1. BT 4.1+EDR
2. 3.5mm music line-in function
3. The headphone battery power status shows on iOS
4. aptx audio technology
How to Use
1. General Function
2. Basic Buttons Operation
Power on: Press the button“ ”for 2 seconds.
Power off: Press the button“ ”for 3 seconds.
Volume adjust: Press the button"+" to increase the volume.
Press the button "-" to decrease the volume .When volume
reaches to maximum or minimum,"Tick"reminding voice
occurs.
Play/Pause: Short press the button button“ ”to pause.
Press it again to continue.
Ope ratio n LE D S tatus
Charging
Red LED keeps lighting during charging
Blue LED keeps lighting charging finished
Congratulations! Thank you for choosing DOSS ANC BE2
BT stereo headphone. We are encourage you to read this
manual guide thoroughly to get most out of the innovate
BT stereo headphone
Connection Diagram
23
What’s in the Box
Previous: Short press the button “<”, music turns
to previous song .
Next: Short press the button “>”, music turns to next song.
Answer Call: Short press the button“ ” to answer the
incoming call.
End call: Short press the button“ ” to end the phone call
Reject call: Press the button “+” for 2 seconds to reject
the call.
Transfer call: During the call , press the button “+” for 2
seconds to switched to mobile phone. Press it again for 2
seconds to switched to headphone.
1. 1 X Stereo BT headphone DOSS ANC BE2
2. 1 X Micro USB charging cable
3. 1 X User manual
4. 1 X 3.5mm audio cable
5
.
1 X Storage bag
6.Specification
BT version: V4.1
Music play time: 20 hours
Max operation range: 10 meters
Supported Bluetooth profiles: A2DP/ AVRCP/ HSP /HFP
Electrical impedance: 32Ω
Sound pressure level: 115±3dB
Frequency response: 20Hz---20KHz
Net weight: 270g
Dimension:
Input: 5V 1A
Battery type: Li-ion 3.7V, 450mAh
190 x 164 x 75mm
Warning
Use the included charging cable or the cable from
qualified manufacturer to charge the headphone.
47
DOSS ANC BE2
User Manual 3.5mm Audio Cable
Auto power off: Headphone will auto power off without
connecting in 30 minutes.
3.Connect Headphone with Devices via 3.5mm Audio Cable
1. Make sure the headphone is power on.
2. Press and hold the the button“ ”for 5 seconds till the red
and blue led flash alternately to enter into the pairing mode.
5 6
NC
5.Active Noise Cancellation Function(ANC)
Email:Support@dossav.com
Website:www.dossaudio.com
Made in Shenzhen,China
NOTE: In Bluetooth mode, if there is no audio input over 6
seconds, the speaker would automatically switch to power
saving mode. A 5-second buffer would be needed if there
comes audio input again.
Power on
Power off
Pairing
Tips: Please adjust the volume on your device in need while
using 3.5mm audio cable.
4.Connect the Headphone with Devices via Bluetooth
3. Discover”DOSS ANC BE2”on your Bluetooth list.
4. Enter”0000”as the PIN if your mobile phone reminds.
5. If the pairing is sucessful, the the LED will change to fast
flashing every 5 seconds, if the pair is failed, please repeat
steps 2 through 3 again.
Short press the button " NC" to cancel the background noise,
which can remove the noise up to 90% under the low
frequency, provides you excellent sound quality.
Do NOT drop, hit or shake the device.
Do NOT disassemble, repair or modify the headphone
by yourself.
Do NOT use cleaning products that contain benzene,
solvents or alcohol.
Do NOT expose the headphone to excessive heat or direct
sunlight for long periods of ttime
Do NOT store the device in a place with humidity or dust.
Do NOT place heavy objects on top of the headphone.
Do NOT use near a microwave oven or wireless LAN products.
—
---
volumeUp
RejectCall/Transfer Call
Previous
LEDlndicator
Turn on/off
PairingMode/
Play/Pause
AnswerCall/End Call/
Next
VolumeDown
Mic
3.5mmAudio Jack
MicroUSB Slot
