DoubleSight DS-10U User manual

REV. 1.0

Contents
Before the use
2
4
5
6
Use of product
How to Connect & Use
Driver Installation
USB Monitor Restrictions
.........................................
.............................................
........................................
7
8
13
User's Guide
Symptoms for possible problems and responses
Specication
.......................
.................................................
14
17
Before the use
Product Conguration
Monitor Assembly
Model name & function
...............................................
.........................................
.............................................
.........................................
USB MONITOR 1

USB MONITOR 2
Before the use
Before the use
Caution for safety
Cautions
※Warning :
※ Caution :
It displays the cases where a mistaken handling may cause an infliction of
death or serious injury to a person.
It displays the cases where a mistaken handling may cause an infliction of
physical injury to a person or property damage to a person.
※ For environment, do not dispose this product to the waste can and make sure to
collect in separate disposal.
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user
that changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate to the equipment.
FCC compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1)This device may not cause harmful interference, and(2) the device must accept any interference
received, including interference that may cause undesired operation.
Information to user
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, use and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is on guarantee that
interference will not occur in a particular installation.
If this equipment dose cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Make sure to read the contents before use.
USB MONITOR 3
Before the use
Do not disassemble without authorization and inquire A/S Center for any
problem.
- When contacting to the inside, it may cause fire or electric shock.
When there is any strange sound or smoke and odor, pull it off from the cab
le immediately.
- It may cause fire or electric shock.
- Make sure to use the power with the USB Cable (DC 5V)
(There is no need for separate power.)
Use the product in a place where there is no inflammation or furnace, or
humidity.
- It may cause fire or electric shock.
Do not put chopstick, driver or other foreign substance to the inputting area
of the product.
- It may cause fire or electric shock.
When the product is cleaned, wipe off with soft fabric, not water mop.
- It may cause fire or electric shock by having the moisture to enter into the
gap of the external part.
- LCD may be damaged if it is scratched or pounded with a sharp object.
Do not install the product in a shaking place or out of reach of children.
- When dropping the product, it may damage to product or a child may
cause the product to fall.
Do not use the product in close distance from the product with inflammatory
substance or combustible spray and others.
- It has the risk of fire.
(Reference : This image may differ depending on each case for reference only.)

USB MONITOR 4
Before the use
Product Conguration
DS-70 & DS-90U Series
Version1.0
· Monitor Driver
· User’sManual
DS-70 & DS-90U
&DS
S
Version1.0

Before the use
Monitor Assembly
Stand assembly-type
USB MONITOR 5
Fixed handle
Stand

Before the use
USB MONITOR 6
Model name & function
LEFT
RIGHT
REAR
BOTTOM
FRONT
4
TOP
3
3
Stand fixing hole
5Pin Min USB Port
Power button
Bir + , -
2
1

USB MONITOR 7
Use of product
How to Connect & Use
Connect USB Monitor
Minimal requirement of system
CPU
RAM
USB Port
HARD Disk
Supporting OS
Intel Pentium/Celeron,AMD/K6/Athlon/Duton 1.2Ghz
512MB RAM or more
2 or more of USB2.0 (It is recommended to use two with the dierence of some PC spec.)
Spare space of 50MB or more
The OS spec of PC can be conrmed from the 'General' tap of the system registration information window
by selecting the 'attribute' with the right button of the mouse in 'My Computer' on the 'base screen.
(1) Windows XP (32bit: Support, 64bit: Not support)
- Service Pack 1 and previous version: Not support
- Service Pack 2 and following version: Support
(2) Windows 2000
- Service Pack 3 and previous version: Not support
- Service Pack 4 and following version: Support
(3) Windows Server 2003: Not support
(4) Windows Vista: Support (32bit or 64bit support)
(5) MAC OSX (Intal MAC) Require separate program
(6) Schedule to support when releasing Windows 7
Use the USB cable to connect the monitor and PC.
■
■Terminal A (5Pin Min USB) connects the monitor and two terminal B (Serial A USB) to PC.
A
B
or
* The USB cable is used with the cable provided at the time of purchase.

Driver installation
Use of product
Driver Installation
USB MONITOR 8
■When the PC booting is completed, begin installation after connecting the USB cable.
You can see the right screen when you
insert CD into CD-ROM.
Monitor Driver
Double click to install USB monitor driver.
* Please check your model name.
Monitor & Touch Installation
Double click to install USB monitor &
touch driver.
* Please check your model number.
User's manual
Double click to see the user's manual.
* Please refer to Help unless you can see
the user's manual.
1.
Select your language and click "I
Accept".
2.
Installation screen appears.3.
(1)
(2)
(3)

Use of product
When completing the installation,
setting has to be made as follows to use
the monitor.
Press the right button on the base
screen to have the 'Display Registration
Information' window.
Click the 'setting' tap, all monitors
connected are displayed.
After completely installed, it is recommended to end the PC and re-start.
* When a problem arises, it is recommended to re-booting of the PC.
4.
After completing the installation, the icon in the monitor shape is generated on the tray on
lower right side of the monitor and the USB monitor information installed is displayed.
5.
Drag the monitors shown on the [Display Registration Information] window to arrange in
sequence of actual use.
7.
After setting up by pressing the 'Application' button, press the 'Confirmation' button to end.
* This USB monitor has the fixed resolution of 7":800x480, 8.9":1024x600.
8.
6.
(1)
(2)
USB MONITOR 9

Use of product
USB Monitor Display Information setting
1. When the USB monitor and PC are
connected with the USB cable and the
driver installation is completed, the
system tray on the right side of the
screen generates the icon of the
monitor shape.
2. Click the monitor-shaped icon to press
the right mouse button to display the
set menu.
(1)
(2)
(3)
(4)
(5)
(6)
Resolution (R)
This is to display the current USB monitor resolution.
(However, this product 7" 800*480, 8.9" is the fixed resolution of 1024*600.)
Color quality (Q)
16-bit and 32-bit may be set up.
Screen Turning (T)
The screen direction may be set when pivoting the product.
* The initial set status is 0 degree.
Direction of expansion
When extending the screen, it may set the USB monitor extension
location.
Extension (E)
The USB monitor may be used with the screen extension mode of the main monitor.
* The initial set status is the 'Extend' mode.
Mirror (M)
The USB monitor may be used with the same screen mode of the main monitor.
* For the mirror mode, the screen is modified with the recommended resolution of the two screens.
(Changing of the main monitor to lower resolution is not a defect.)
USB MONITOR 10

Touch Screen Setting(For DS-10UT)
Use of product
(7)
(8)
Turning off (O)
The USB monitor screen is turned OFF. Under the Off condition, it still maintains the turning off
condition while the PC is turned off that select "E" or "M" to have the screen back on the USB monitor.
Advanced class (A)
It moves to the display set mode.
USB MONITOR 11
USB Controller icon appears when
touch screen driver is ready.
1.
Click "Yes"3.
Check "Enable Multiple Monitors" and
double click the monitor setting screen.
2.

Use of product
Calibration Setting
■
USB MONITOR 12
Click "Apply" when outline of display
screen is changed to white line.
4.
Click "Tools"tab and "4 points Calibration"1.
Click "Yes"5.
Click "Yes"6.

USB MONITOR 13
Use of product
Hold pressing flickering point until it to finish
flickering and continue to enter next
calibrations. (Enter 4 points)
2.
Calibration setting is completed After entering
4 points.
* Please reboot PC when driver installation is completed.
3.
Support spec
■
USB Monitor Restrictions
This monitor is the USB monitor recognized as the USB device that the DOS screen shown in
the PC booting will not be displayed.
SW that uses the 3D acceleration function in HW cannot be used in the USB monitor. -
Real Player (Do not support the extension mode.)
- Most of 3D game
- Program driven by the basis of Direct X
Supporting moving picture program
- Power DVD
- Win DVD (supporting version 5 or higher)
- Windows Media Player (supporting Version 10 or previous version)
- VLC
- Gom Player
On USB 1.0, the USB monitor may not normally operated.
The power at USB 1 Port is weak that it may not be operated in some PC that it is
recommended to use 2 USB Ports.
PC H/W spec possible for extension
- Connect 2 USB monitors: Minimum of 1.2GHz CPU / 512 MB Memory
- Connect 3 USB monitors: Minimum of 1.8GHz CPU / 1 MB Memory
- Connect 6 USB monitors: Minimum of 1.6GHz Dual core CPU / 512 MB Memory
●
●
●
●
●
●

User's Guide
USB MONITOR 14
After reconnecting USB cable, please check out the "USB Connection" icon on touchside.
* If there is no icon, reconnect USB cable and on again.
When you change USB port or calibration get twisted, click 'Touchside - Tool - 4Points
Calibration" and reset calibration.
Reboot PC after driver installation.
A : (1)
(2)
(3)
Touch Screen doesn't work.
Q :
In the PC with on-board type that uses the i815 chip set mother board has to re-boot by
changing the legacy USB support option to [No Change] at the BIOS set menu.
* The entry method of BIOS may differ depending on the PC that the manual of the PC in use has
to be referred to. For detailed information, refer to the homepage of Microsoft.
(1)
The screen on the USB monitor has stopped its motion.
Q :
Booting is not made after linking the USB monitor.A :
Select Program 'Add/Remove' from the control board to select the Displaylink Graphics
from the list of 'currently installed programs' and click "Remove" to delete.
How can I remove the installed program of the USB monitor?
Q :
A :
Check if the USB cable is correctly linked and if the USB Driver is installed.
Check if the blue LED color on the USB monitor is come on and if the power button is
turned Off.
Check if the tray monitor icon on the lower side of the monitor has 'Off'.
The USB monitor reads the general USB device on the PC. If quick and repeated turning on
and off is made, the USB vice may have problems that you may refer to problem solving
method for the USB device from the Customer Support site of Microsoft.
- Press the right button from "My Computer" of the base screen to display the 'Attribute' window.
- Click the system administrator.
- Press the HW change search from the motion menu.
- Re-boot the PC.
Symptoms for possible problems and responses
■When there is any problem, make sure to check the followings first.
A : (1)
(2)
(3)
(4)
The USB monitor screen is not displayed.
Q :

When you use Skype video chat with Window XP OS, there may be flicker or distortion in
screen.
User's Guide
USB MONITOR 15
Click 'Troubleshoot' tap.
Set 'hardware acceleration (H)'to None, and click 'Apply (A)' button.
(3)
(4)
The use of DirectX function causes this symptom.
Make sure not to use it on the graphic card setting because there is no option to disable this
function on SKYPE.
OS: Windows XP
On the desktop, right-click to display 'Display Properties' window.
Click 'Settings' tab and click Advanced (V).
A :
(1)
(2)
Q :

User's Guide
USB MONITOR 16
Select program 'Cumstomize colors' from the control panel(1)
OS:Windows Vista
Click "Window Aero"
Click "Apply"
(1)
(2)
OS: Windows Vista Home premium, Business, Ultimate
Click "Windows Vista Standard "
Click "Apply"
(1)
(2)
OS: Windows Vista Home basic

User's Guide
USB MONITOR 17
Specication
DS-10UT
(Resistive Touch)
DS-10U
10.1” TFT LCD Panel(LED Backlight System)
WSVGA (1024 x 600 )
262K Colors
500:1
45/45/15/35
16ms
: 0.61Kg
122
247.66
153.06
18.95
222.78
13.85