Dr. Trust Comfort User manual

Range & broadcasting
Systolic Blood-pressure
DiastolicBlood-pressure
Measures
Hypotension
lower than 100
lower than 60
Consult your doctor
Optimal BP
between 100 and 120
between 60 and 80
Self-check
Normal BP
between 120 and 130
between 80 and 85
Self-check
High To Normal BP
between 130 and 140
between 85and 90
Consult your doctor
Slight Hypertension
between 140 and 160
Between90and 100
Seek medical advice
Medium Hypertension
between 160 and 180
Between100and 110
Seek medical advice
Strong Hypertension
Higher than 180
Higher than 110
Urgently seek medical
advice!

Error No.
Possible cause(s)
ERR 1
No pulse has been detected.
ERR 2
Unnatural pressure impulses influence the measurement result.
Reason: The arm was moved during the Measurement (Artefact).
ERR 3
The inflation of the cuff takes too long. The cuff is not correctly seated.
ERR 5
The measured readings indicated an unacceptable difference between systolic and
diastolic pressures. Take other reading following directions carefully. Contact you doctor
if you continue to get unusual readings.
Err8
The pressure in the cuff is too high (over 290 mmHg)

Malfunction
Remedy
The display remains empty when the
instrument is switched on although the
batteries are in place.
1. Check batteries for correct polarity and if necessary insert
correctly.
2. If the display is unusual, re-insert batteries or exchange
them.
The device frequently fails to measure the blood
pressure values, or the values measured are too
low (too high).
1. Check the positioning of the cuff.
2. Measure the blood-pressure again in peace and quiet under
observance of the details made under point 5.
Every measurement produces a different value
although the instrument functions normally and
the values displayed are normal
1. Please read the following information and the points listed
under «Common sources of error». Repeat the measurement.
Please Note: Blood pressure fluctuates continually so
successive measurements will show some variability.
Blood pressure measured differs from those
values measured by the doctor.
1. Record the daily development of the values and consult
your doctor.
Please Note: Individuals visiting their doctor frequently
experience anxiety which can result in a higher reading at the
doctor than obtained at home under resting conditions.

IEC60601-1-6:2010+A1:2013/ EN60601-1-6:2010+A1:2015
IEC60601-1:2005+A1:2012/EN60601-1:2006+A11:2011+A1:2013+A12:2014
IEC60601-1-2:2014/ EN60601-1-2:2015
IEC/EN60601-1-11:2015
IEC80601-2-30:2009+A1:2013/EN80601-2-30:2010+A1:2015
Some electrical and electrical
equipments forbid to abandon
and disposal at will
TUV NO.
Manufacturer’s name and
address
Reading Instruction Book before
use
Inapplicable baby
Type B equipment
Cuff Connector
Protection against
ingress of water:
IP22

Immunity test
IEC60601-1-2 test
level
Compliance level
Electromagnetic environment
-guidance
Electrostatic
discharge (ESD) IEC
61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete
or ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30 %.
Electric fast
transient/ burst IEC
61000-4-4
±2 kV for power
supply lines
±1 kV for
input/output lines
Not applicable
Mains power quality should be
that of a typical commercial or
hospital environment.
Surge IEC 61000-4-5
±1 kV differential
mode
±2 kV common
mode
Not applicable
Mains power quality should be
that of a typical commercial or
hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines IEC 61000-4-11
<5 % UT（95% dip
inUT.） for 0.5 cycle
40 % UT （60% dip in
UT ）for 5 cycles
70 % UT(30% dip
inUT) for 25 cycles
<5 % UT（95% dip
inUT）for 5 sec.
Not applicable
Mains power quality should be
that of a typical commercial or
hospital environment. If the user of
the upper arm style requires
continued operation during power
mains interruptions, it is
recommended that Dr Trust BP
Check with MDI be powered from
an uninterruptible power supply or
a battery.
Power frequency
(50/ 60 Hz) magnetic
field IEC 61000-4-8
3 A/m
Not applicable
Not applicable
Note: U
T is the a.c. mains voltage prior to application of the test level.
Im m unity test
IEC60601-1-2
test level
IEC60601-1-2
test level
Electromagnetic environment - guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms 150 kHz
to 80 M Hz 80%
AM (2Hz)
3 Vrms 80 MHz
to 2.5 GHz 80%
AM (2Hz)
3 Vrms
3 V/m
Portable and m obile RF com munications equipm ent
should be used no closer to any part of Dr Trust BP Check
with MDI , including cables, than the recom mended
separation distance calculated from the equation
applicable to the frequency of the transmitter.
Recomm end separation distance
3V
d = 1.2×p
1/2 80Mhz to 800 MHz
d = 2.3×p
1/2M Hz to 2.5 GHz
Where P is the m aximum output power rating of the
transmitter in watts (W) according to he transmitter
manufacturer and d is the recomm ended separation
distance in meters (m).
Field strengths from fixed RF transmitters as determ ined
by an electromagnetic site survey
a, should be less than the
com pliance level in each frequency range
b. Interference
may occur in the vicinity of equipm ent marked with the
following symbol:

Rated maximum output
power of transmitter
(W)
Separation distance according to frequency of transmitter m
150 kHz to 80 MHz
d = 1.2×p1/2
80 MHz to 800 MHz
d = 1.2×p1/2
800 MHz to 2.5 GHz
d = 2.3×p1/2
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23