Draper 59085 User manual

UNIVERSAL VALVE
SPRING COMPRESSOR
■STOCK No.59085 ■PART No.VSC/UNI
01/2000
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE
THE SAFE AND EFFECTIVE USE OF THIS TOOL.
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hants. SO53 1YF. England.
Tel: [phone].
Fax: [phone].
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.
YOUR DRAPER STOCKIST

8. Check that the valve adaptor lines up correctly
with the valve holder. If the adaptor does not
line up correctly, adjust the support bar, upright
supports or compression
handle/valve adaptor as necessary.
9. Once the valve adaptor is lined up correctly
tighten the upright support bolts.
10.Re-check that the air supply is correct, line up
the valve adaptor and depress handle. The
valve spring will then be depressed and the
collets can be removed.
11. Renew valve stem seal or spring, replace collets
by re-compressing the spring and re-inserting
the collets.
12.Repeat instructions 5-11 for other valves as
necessary.
NOTE: These instructions are for guidance only
for concise and detailed instructions refer to the
Vehicle Manufacturer’s service manual or
relevant Hayne’s Service manual.
Fig.4.
Fig.5.
INTRODUCTION
Universal Valve Spring Compressor
This tool has been designed specially for removing and installing valve springs and seals
without the need to remove the cylinder head from the engine block. However it can also be
used on a cylinder head which has been removed from the block.
WARNING: Always wear safety goggles when using this tool.
- 1-
ASSEMBLY
1. Secure the two upright supports to the head
using the bolts supplied or Cam cover
fixings. (Do not fully tighten the bolts at this
time). See FIG 1.
2. Locate the compression handle (A) into the slot
in the valve adaptor (B) and secure using
one of the securing pins (C), see FIG 2.
NOTE: There are several holes located in both
the compression handle and valve adaptor,
these are for the proper location of the adaptor
on the valve.
3. Locate the support bar through the upright
supports as shown in FIG 3.
NOTE: There are seven holes in each upright for
correct positioning of the valve adaptor.
4. Remove the spark plugs or diesel injectors from
the engine.
5. Screw the required adaptor into the plug or
injector of the valve spring or valve guide to
be replaced and tighten (finger tight), see FIG 4.
6. Connect the adaptor to an air supply at 90PSI.
7. Place the compression handle under the support
bar noting that there are two locating
slots on the handle. See FIG 5.
Fig.1.
Fig.2.
Fig.3.
✫✌ ✬✌
✪✌

8. Check that the valve adaptor lines up correctly
with the valve holder. If the adaptor does not
line up correctly, adjust the support bar, upright
supports or compression
handle/valve adaptor as necessary.
9. Once the valve adaptor is lined up correctly
tighten the upright support bolts.
10.Re-check that the air supply is correct, line up
the valve adaptor and depress handle. The
valve spring will then be depressed and the
collets can be removed.
11. Renew valve stem seal or spring, replace collets
by re-compressing the spring and re-inserting
the collets.
12.Repeat instructions 5-11 for other valves as
necessary.
NOTE: These instructions are for guidance only
for concise and detailed instructions refer to the
Vehicle Manufacturer’s service manual or
relevant Hayne’s Service manual.
Fig.4.
Fig.5.
INTRODUCTION
Universal Valve Spring Compressor
This tool has been designed specially for removing and installing valve springs and seals
without the need to remove the cylinder head from the engine block. However it can also be
used on a cylinder head which has been removed from the block.
WARNING: Always wear safety goggles when using this tool.
- 1-
ASSEMBLY
1. Secure the two upright supports to the head
using the bolts supplied or Cam cover
fixings. (Do not fully tighten the bolts at this
time). See FIG 1.
2. Locate the compression handle (A) into the slot
in the valve adaptor (B) and secure using
one of the securing pins (C), see FIG 2.
NOTE: There are several holes located in both
the compression handle and valve adaptor,
these are for the proper location of the adaptor
on the valve.
3. Locate the support bar through the upright
supports as shown in FIG 3.
NOTE: There are seven holes in each upright for
correct positioning of the valve adaptor.
4. Remove the spark plugs or diesel injectors from
the engine.
5. Screw the required adaptor into the plug or
injector of the valve spring or valve guide to
be replaced and tighten (finger tight), see FIG 4.
6. Connect the adaptor to an air supply at 90PSI.
7. Place the compression handle under the support
bar noting that there are two locating
slots on the handle. See FIG 5.
Fig.1.
Fig.2.
Fig.3.
✫✌ ✬✌
✪✌

UNIVERSAL VALVE
SPRING COMPRESSOR
■STOCK No.59085 ■PART No.VSC/UNI
01/2000
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE
THE SAFE AND EFFECTIVE USE OF THIS TOOL.
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hants. SO53 1YF. England.
Tel: [phone].
Fax: [phone].
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.
YOUR DRAPER STOCKIST