Draytek VigorBX 2000 Series User manual

ii
VigorBX 2000 Series
IPPBX Firewall Router
Quick Start Guide
Version: 1.0
Firmware Version: V3.8.1_RC4a
(For future update, please visit DrayTek web site)
Date: August 10, 2015

i
Intellectual Property Rights (IPR) Information
Copyrights © All rights reserved. This publication contains information that is protected
by copyright. No part may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language without written permission
from the copyright holders.
Trademarks The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and
Explorer are trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of
their respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired
only be authorized and qualified personnel. Do not try to open or
repair the router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
Do not stack the routers.
The router should be used in a sheltered area, within a
temperature range of +5 to +40 Celsius.
Do not expose the router to direct sunlight or other heat sources.
The housing and electronic components may be damaged by direct
sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent
electronic shock hazards.
Keep the package out of reach of children.
When you want to dispose of the router, please follow local
regulations on conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free
from any defects in workmanship or materials for a period of two (2) years
from the date of purchase from the dealer. Please keep your purchase receipt
in a safe place as it serves as proof of date of purchase. During the warranty
period, and upon proof of purchase, should the product have indications of
failure due to faulty workmanship and/or materials, we will, at our discretion,
repair or replace the defective products or components, without charge for
either parts or labor, to whatever extent we deem necessary tore-store the
product to proper operating condition. Any replacement will consist of a new
or re-manufactured functionally equivalent product of equal value, and will
be offered solely at our discretion. This warranty will not apply if the product
is modified, misused, tampered with, damaged by an act of God, or subjected
to abnormal working conditions. The warranty does not cover the bundled or
licensed software of other vendors. Defects which do not significantly affect
the usability of the product will not be covered by the warranty. We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any
person of such revision or changes.

ii
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu
County, Taiwan 303
Product: VigorBX 2000 Series
DrayTek Corp. declares that VigorBX 2000 Series of routers are in compliance with the following
essential requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC
and RoHS 2011/65/EU.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
2004/108/EC by complying with the requirements set forth in EN55022/Class B and
EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by
complying with the requirements set forth in EN60950-1.
This product is designed for DSL, POTS and 2.4GHz/5GHz WLAN network throughout the EC
region and Switzerland with restrictions in France. Please see the user manual for the applicable
networks on your product.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause
undesired operation.
More update, please visit www.draytek.com.
Due to the US Patent No. 7,127,048, the DSL and VoIP applications on Vigor BX 2000 series can
not be allowed to promote and to sell in the USA.

iii
Be a Registered Owner
Web registration is preferred. You can register your Vigor router via http://www.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
Please consult the DrayTek web site for more information on newest firmware, tools and
documents.
http://www.draytek.com

iv
T
Ta ab bl le e o of f C Co on nt te en nt ts s
1. Introduction........................................................................................................... 1
2. Package Content .................................................................................................. 2
3. Panel Explanation................................................................................................. 3
4. Hardware Installation ........................................................................................... 6
5. Software Configuration........................................................................................ 8
5.1 Quick Start Wizard for Network Connection............................................................................... 8
5.2 IPPBX Wizard for VoIP............................................................................................................. 13
6. Customer Service............................................................................................... 18

1
1
1. . I In nt tr ro od du uc ct ti io on n
The VigorBX 2000 is an VDSL2 router with IP PBX function and 2nd Ethernet WAN.
This 2nd WAN can connect to DSL/Cable modem or fiber media converter for
policy-based load-balance, fail-over and BoD (Bandwidth on Demand); it also
features advanced bandwidth control mechanism such as IP-layer QoS, NAT
Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable
access control and bandwidth management.
The SPI (Stateful Packet Inspection) firewall uses object-based design to make
settings of firewall policies easy. The CSM (Content Security Management)
feature allows more precise and efficient access control for URL/Web Content
Filtering, IM (Instant Messenger) and P2P (Peer to Peer) applications.
With hardware-based implementation of the VPN protocols, the VigorBX 2000
supports up to 32 VPN tunnels using advanced protocols such as
IPSec/PPTP/L2TP/L2TP over IPSec with AES/DES/3DES for encryption and
MD5/SHA-1 for authentication.
VigorBX 2000 can provide up to 50 extensions setup to let all registered IP phones
in LAN or remote sites around the world to have unlimited free calls through
Internet. Moreover, VigorBX 2000 is able to establish multiple networking
architectures corresponding to your current desire and future needs of growing
communication. Its PSTN compatibility lets you move from simple VoIP solution
such as IP phone and Softphone to integrate with comprehensive networking
infrastructure, such as Analog phone line any time you need.

2
2
2. . P Pa ac ck ka ag ge e C Co on nt te en nt t
Take a look at the package content. If there is anything missed or damaged,
please contact DrayTek or dealer immediately.
VigorBX2000
Quick Start Guide
RJ-45 to RJ-45 Cable
(Annex B)
RJ-11 to RJ-45 Cable (Annex B)
RJ-11 to RJ-11 Cable (Annex A)
Phone Adapter
Antenna (ac models)
The type of the power adapter depends on the country that the router will be
installed. * The maximum power consumption is 17-23 Watt.
UK-type Power Adapter
EU-type Power Adapter
USA/Taiwan-type Power Adapter
AU/NZ-type Power Adapter

3
3
3. . P Pa an ne el l E Ex xp pl la an na at ti io on n
LED Status Explanation
Blinking The router is powered on and running normally.ACT
(Activity) Off The router is powered off.
On A USB device is connected and active.USB1~USB2
/ USB Blinking The data is transmitting.
On The WAN2 connection is ready.WAN 2 Blinking It will blink while transmitting data.
On The router is ready to access Internet through DSL link.DSL Blinking Slowly: The modem is ready.
Quickly: The connection is training.
On VPN tunnel is up and down.
Off VPN services are disabled.
VPN
Blinking Traffic is passing through VPN tunnel.
On Wireless access point with bandwidth of 2.4GHz/5GHz is
ready.
2.4G/5G
Blinking It will blink slowly while wireless traffic goes through.
ACT and WLAN LEDs blink quickly and simultaneously when
WPS is working, and will return to normal condition after
two minutes. (You need to setup WPS within 2 minutes.)
On A PSTN phone call comes (in and out). However, when the
phone call is disconnected, the LED will be off about six
seconds later.
Line1~Line2
Off There is no PSTN phone call.
On The phone connected to this port is off-hook.
Off The phone connected to this port is on-hook.
Phone
Blinking A phone call comes.
LED on Connector On The port is connected.
Off The port is disconnected.
Left LED
(Green) Blinking The data is transmitting.
On The port is connected with 1000Mbps.
WAN 2
Right LED
(Green) Off The port is connected with 10/1000Mbps.

4
On The port is connected.
Off The port is disconnected.
Left LED
(Green) Blinking The data is transmitting.
On The port is connected with 1000Mbps.
LAN 1~LAN6
Right LED
(Green) Off The port is connected with 10/100Mbps.
Interface Description
Wireless LAN
ON/OFF/WPS
Wireless band will be switched /changed according to the
button pressed and released. For example,
2.4G (On) and 5G (On) – in default.
2.4G (Off) and 5G (On) – pressed and released the button
once.
2.4G (On) and 5G (Off) – pressed and released the button
twice.
2.4G (Off) and 5G (Off) – pressed and released the button
three times.
When WPS function is enabled by web user interface, press this
button for more than 2 seconds to wait for client’s device making
network connection through WPS.
Factory
Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and
keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will
restart with the factory default configuration.
USB1~USB2 Connecter for a USB device (for 3G/4G USB Modem or printer).
VDSL/ADSL Connecter for accessing the Internet through VDSL/ADSL.
WAN2 Connecter for remote networked devices.
LAN1~LAN6 Connecters for local networked devices.
Phone Connecter for PSTN phone.
Line1/2 Connector for PSTN life line.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

5