Drayton 22083 User manual

Drayton
Digistat +3 / +3RF
Programmable Room Thermostat
5-2 Day / 7 Day
Models: 22083, 22087 / RF701, 22092
QUICK START GUIDE
Drayton Digistat +3 and +3RF
The Digistat +3/+3RF thermostat is a programmable thermostat with 5-2 Day or 7 day
timings and 6 time/temperature events during the day.
Clock Setting
Your Digistat +3/+3RF is fitted with a “real-time clock”, which is “pre-set” at the factory;
you will not have to alter the time settings. A special feature of this real-time clock is it
will automatically change over during the GMT/BST summer/winter change over removing
the need to manually alter the clock.
General Operation
Programmable thermostats do not have “On” and “Off” times like traditional timers.
They offer temperature control both day and night and you simply select which
temperatures you require at which times of the day.
With the unit in “Auto-Mode” (the small arrow to bottom of screen will point to Auto) the
temperature can be changed for a short time by using the or buttons. Changing the
temperature in this way will keep the Digistat +3/+3RF set to your new temperature until
the next pre-programmed event (at which time it will revert to programmed temperature).
The temperature you are setting will flash on the screen. Once temperature is set, the
unit will revert to showing the room temperature. The indicator will show on the
screen if the heating is calling for heat.
TO ADJUST THE TIMES AND TEMPERATURES FOR 7-DAY OPERATION:
Congratulations!
The unit is now set correctly to follow your required timings.
6. With the product operating as normal
in the “Auto” mode, press once
and then press the button until the
display is flashing and shows.
7. Press the once, the display will
be as shown. The time will be flashing,
use the or buttons to adjust the
1st time as required.
8. Once time has been set, press
and use the or buttons to adjust
required temperature. Repeat the
above steps 7-8 until the 6 periods
have been set for Monday.
9. Once Monday has been set, press
once. Repeat steps 7-8 until all 7 days
of the week have been set.
10. Once the final temperature has been
set press the to confirm settings.
To exit press or until you
return to auto mode with the bottom
arrow pointing at Auto.
(* small 1 in lower half of screen shows which time
period is being set e.g. 1=1st period,
2 = 2nd period etc)
Invensys Controls Europe
Customer Service Tel: [phone]
Customer Service Fax: [phone]
Technical Helpline Tel: [phone]
Website: www.draytoncontrols.co.uk
Email: customer[email protected]
Quick Commissioning Guide 06490122001 IssA

*The above settings can be understood using the chart below:
*The above settings can be understood using the chart below:
Programming the Digistat +3/+3RF
Your Digistat +3/+3RF comes with the following settings pre-programmed for your
convenience:
Pre-set program 1 (9 til 5) WEEKDAY
Event 123456
Time 6:30 8:30 12:00 14:00 16:30 22:30
Temperature 20.0 16.0 16.0 16.0 21.0 7.0
Pre-set program 1 (9 til 5) WEEKEND
Event 123456
Time 7:00 9:00 12:00 14:00 16:00 23:00
Temperature 20.0 18.0 21.0 18.0 21.0 7.0
123456
25ºC
20ºC
15ºC
10ºC
5ºC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period Monday - Friday
Room Temp
As you can see, at 06:30, the heating will
come on to raise the temperature to
20ºC. At 8.30, the temperature set point is
dropped from 20ºC down to 16ºC, at which
time it stays at 16ºC throughout the day,
until 16:30 when the temperature increases
to 21ºC. The temperature then drops down
to a night-setback temperature of 7ºC until
06:30 when the cycle repeats for the next
day (Monday to Friday) or changes to
weekend settings see below.
As you can see, at 07:00, the heating will
come on to raise the temperature to 20ºC. At
9.00, the temperature set point is dropped
from 20ºC down to 18ºC, it stays at 18ºC until
12.00 when the heating comes to raise the
temperature to 21ºC. The temperature stays
at 21ºC until 14.00 when it drops down to
18ºC. at 16.30 the heating comes on to raise
the temperature to 21ºC where it stays until
23.00 when the temperature then drops
down to a night-setback temperature of 7ºC
until 07.00 when the cycle repeats for the
next day (Saturday and Sunday) or changes
to weekday settings see above.
1 2 3 4 5 6
25ºC
20ºC
15ºC
10ºC
5ºC
07:00 09:00 12:00 14:00 16:00 23:00
Time Period Saturday-Sunday
Room Temp
TO ADJUST THE TIMES AND TEMPERATURES FOR 5-2 DAY OPERATION:
Congratulations!
The unit is now set correctly to follow your required timings.
1. With the product operating as normal
in the Auto mode press once and
then press the button until the
display is flashing and shows:
2. Press the button once, the
display will be as shown. The time will
be flashing, use the or button
to adjust the 1st time as required.
3. Once time has been set, press
and use the or button to adjust
required temperature (shown flashing).
Press to confirm and move to
the next time and temperature periods
to be adjusted confirming changes by
pressing (max. 6 periods).
4. Once the last weekday temperature
period has been set, press once
to confirm settings and allow
adjustment of the weekend program.
Use the and buttons and the
button to set the 6 periods for
the weekend program.
5. Once the final temperature has been
set press to confirm setting. To
exit press or until you
return to auto mode with the bottom
arrow pointing at Auto.
(* small 1 in lower half of screen shows which
time period is being set e.g. 1=1st period,
2 = 2nd period etc)