dreambaby AVA F2095 User manual

INSTRUCTIONS
1
Item numbers may also end in BB.
SECURITY GATE
AVA
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
If you sell or give away this product, make sure you give this instruction to the new owner.
Can be used in conjunction with a Dreambaby
®
Watch-the-Step®Gate Ramp (F837) to help avoid tripping.
F2095
F2096
F2097
F2098
CAUTION: With any pressure mounted gate, a construction bar is required across the base.
Note, this bar can be a tripping hazard. If you choose to position a pressure mounted gate
at the top of stairs, use extra caution to step over this bar to prevent trips and falls.
Conforms to EN1930:2011
WARNING
WARNING - Incorrect installation can be dangerous.
WARNING - Do not use the safety barrier if any components are damaged or missing.
WARNING - The safety barrier must not be fitted across windows.
WARNING - Never use without wall cups.
Screws MUST always be used to install wall cups.
This safety barrier is for domestic use only.
This safety barrier is suitable for use with children up to 24 months of age.
Never use with a child able to climb or dislodge/open gate.
The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound.
If the barrier is to be used at the top of the stairs, it should not be positioned below top level.
If the safety barrier is used at the bottom of the stairs, it should be positioned at the front of
the lowest tread possible.
This gate has a manual close system.
This gate is intended for indoor use and is not to be exposed to outdoor elements.
Install this gate away from heaters and other sources of heat.
This product will not necessarily prevent all accidents.

2
NOTICE TO CUSTOMERS
THE GAP IN THIS GATE IS
NOT A FAULT.
The gap will disappear
when the gate is correctly
installed.
PLEASE INSTALL GATE
ACCORDING TO
MANUFACTURER’S
INSTRUCTIONS.
PARTS LIST
WARNING : This package contains
small parts and sharp points in an unassembled
state. Keep out of reach of children.
Adult assembly required.
IMPORTANT NOTICE
to Customers
Thegap in this gate is NOT a fault.
Thegap will disappear when the
gateis correctly installed.
Referto enclosed instructions for
correctinstallation procedures.
F - Gate Notice
GAP
E x 4
G x 4
Fx 4
H x 4
J x 4
Wood Screws
Wood use only
A Gate Panel
B Upper Locking Set
C Release Switch
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
G Wall Cups
H Double-sided Adhesive Tape
I Lower Locking Set
J Wood Screws
C
A
G
H
I
D
EFB

3
A maximum of 2 Gate Extensions can be used, 1 on each side of gate.
Do NOT install 2 Gate Extensions on the same side of gate.
WARNING
1. Measure the width of the opening of where you intend to install the gate.
For wider openings select the appropriate Gate Extension(s), sold separately.
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster/gyprock alone is not strong enough and not safe).
DO NOT MOUNT TO GLASS.
INSTALLATION
F2097/ F2098
F2095 / F2096
75 - 81cm / 29.5 - 32in
9cm/ 3.5in 9cm/ 3.5in
75 - 99cm / 29.5 - 39in

Screw in Mounting Cups
when using gate on stairs
4
*F901 / L901 - 9cm (3.5in)
F902 / L902 - 18cm (7in)
F903 / L903 - 27cm (10.5in)
F1951 / L1951 - 27cm (10.5in)
F1953 / L1953 - 45cm (17.5in)
F1955 / L1955 - 54cm (21in)
F1957 / L1957 - 63cm (24.5in)
F1959 / L1959 - 100cm (39in)
*F1932 / L1932 - 9cm (3.5in)
WHITE
CHARCOAL
GATE EXTENSIONS sold separately.
DL
K
E
3.5in/9cm
2. To use with Gate Extensions (sold separately).
K
Y
W
XZ
Y
W
For Extensions over 14in / 36cm
Insert LONG END of EXTENSION PIN (K)
into Gate Frame
INSTALLATION ADDING EXTENSION FRAMES
DL
K
K1
K2
K3
3.5in / 9cm
7in / 18cm &
10.5in / 27cm
14in/36cm—
39in/100cm
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
K Extension Pin
L Gate Extension
G Wall Cups
INSTRUCTIONS:
1. Install Lower Clamp
X onto bottom of gate extension using Z .
2. Insert short end of Extension Pin
K into gate frame.
3. Slip the gate extension over pin.
4. Screw Upper clamp
Y into place using W .
PAR TS
K - Extension Pin
W - Screws
X - Lower Clamp
Y - Upper Clamp
Z - Connector Screw
L
3.5in / 9cm
E
F
G
K
D
F
X
ZK
K
X
Insert Extension Pins Kinto the holes on the outside of the Gate Frame D
Next, slip Extension Frames Lover the Pins K.
Finally, slide in the Tension Knobs Eand Bolts with Rubber Pads F.

5
3A
4. Fasten the Wall Cups to the wall with screws AND double-sided adhesive tape (4A & 4B).
NOTE : Ensure that they are aligned vertically, so that the Wall Cups at the top are directly above the ones at the bottom.
3C
3B
Floor Floor Floor
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely flat on the floor (3A),
and it is perpendicular to the openings and the floor (3B & 3C).
If the safety barrier is used at the
top of stairs, it should not be
positioned below the top level.
If the safety barrier is used at the bottom
of the stairs, it should be positioned at the
front of the lowest tread possible.
5. For use on stairs (5A & 5B).
Bottom of stairs
Floor
Top of stairs
INSTALLATION
Landing
5cm
2in
Side view of gate
Top view of gate
Jx 4
Wall Wall
Wall Wall
Wall
WallWall
Wall
Never use without wall cups.
Screws MUST always be
used to install wall cups.
Never use without wall cups.
Screws MUST always be used
to install wall cups.
Wood screws (J) included.
For Brick or Masonry use the appropriate fittings, screws and plugs for
your wall (not included)
G x 4
H x 4 J x 4