dreambaby Chelsea User manual

WARNING - Incorrect installation can be dangerous;
WARNING - Do not use the safety barrier if any components are damaged or missing;
WARNING - The safety barrier must not be fitted across windows;
WARNING - Never use without mounting cups;
This safety barrier is for domestic use only;
This safety barrier is suitable for use with children up to 24 months of age;
Never use with a child able to climb or dislodge/open gate;
The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound;
If the barrier is to be used at the top of the stairs, it should not be positioned
below top level;
If the safety barrier is used at the bottom of the stairs, it should be positioned
at the front of the lowest tread possible;
This gate has an automatic close system;
This gate is intended for indoor use and is not to be exposed to outdoor elements;
Install this gate away from heaters and other sources of heat.
WARNING
INSTRUCTIONS
Chelsea Auto-Close Security Gate
With Stay-Open Feature
F160(N) B/W
F190(N) B/W
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
If you sell or give away this product,
make sure you give this instruction to the new owner.
This safety gate complies with EN1930:2011
F160/F190 fits openings 71-82cm (28-32in).
1

NOTICE TO
CUSTOMERS
THE GAP IN THIS GATE IS NOT A FAULT.
THE GAP WILL DISAPPEAR WHEN THE
GATE IS CORRECTLY INSTALLED.
PLEASE INSTALL GATE ACCORDING TO
MANUFACTURER’S INSTRUCTIONS.
IMPORTANT NOTICE
to Customers
The gap in this gate is NOT a fault.
The gap will disappear when the
gate is correctly installed.
Refer to enclosed instructions for
correct installation procedures.
F - Gate Notice
WARNING: This package contains small parts and
sharp points in an unassembled state. Keep out of
reach of children. Adult assembly required.
PARTS LIST
1 Gate Panel
2 Upper Locking Set
3 Release Switch with Latch
4 Right Upper Corner
5 Tension Knobs
6 Bolts with Rubber Pads
7 Mounting Cups
8 Gate Frame
9 Lower Locking Set
1 2 3 4 5
7
9
8
2
1A
1. Measure the width of the opening of where you intend to install the gate.
Ensure the surface that you are mounting the gate is structurally sound such as solid timber,
brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster/gyprock alone is not strong enough and not safe). Do not mount to glass.
For openings over 82cm (32in) select the appropriate Gate Extension(s).
INSTALLATION
71 - 82cm (28.3 - 32in)
6

3
2. To use with Gate Extensions.
Insert Extension pins into the holes on the outside of the Gate Frame (2A / 2B).
Next, slip Extension Frames over the Pins.
Finally, slide the Tension Knobs and Bolts with Rubber Pads.
27cm9cm9cm18cm27cm9cm9cm18cm
A maximum of 4 Gate Extensions can be used,
2 on each side of gate. Do NOT install 3 Gate Extensions on the same side of gate.
Tension
Knob
Insert LONG END of
EXTENSION PIN
into Gate Frame
Gate Frame *
#159/#192 - 9cm (3.5in)
#171/#193 - 18cm (7in)
#172/#194 - 27cm (10.5in)
#831/#841 - 36cm (14in)
#832/#842 - 45cm (17.5in)
#833/#843 - 54cm (21in)
#834/#844 - 63cm (24.5in)
#835/#845 - 100cm (39in)
Gate Extensions
WARNING
9cm
Tension
Knob
Insert SHORT END of
EXTENSION PIN
into Gate Frame
Gate
Extension
Gate Frame
27cm
Extension Frame Gate Frame
Tension
Bolt
Tension Knob with
Rubber Pads
Extension Pin
*
For 9cm (3.5in) Gate Extensions
For all other Gate Extensions
Gate
Extension
2A 2B

4
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely
flat on the floor (3A), and it is perpendicular to the openings and the floor (3B & 3C).
For use on stairs (3E).
Then fasten the Mounting Cups to the wall with screws or double-sided adhesive tape (3D).
Note: Ensure that they are aligned vertically, so that the Mounting Cups at the top are
directly above the ones at the bottom.
3A
3C
3E
3B
Top view of gate
Side view of gate
If the gate is used at the
bottom of the stairs to prevent
the child from climbing up the
stairs, it must be placed on
the lowest stair.
If the gate is to be used at the top
of the stairs to prevent the child
from falling down the stairs, it
must not be placed on any stair
below the level of the top stair.
Bottom of stairs Top of stairs
floor floorfloor
WARNING
3D
Never use without Mounting Cups.
G x 4J x 4 G x 4J x 4
Fasten Mounting Cups to the wall with
screws or double-sided adhesive tape.

Distance should be equal
Distance should be equal
6B
6C
5
4. Partially slide the Bolts with Rubber Pads and Tension Knobs outwards from the Gate Frames /
Extension Frames into Mounting Cups.
5. Tighten both of the bottom Tension Knobs (5A) by
turning them clockwise at the same time (5A & 5B).
NOTE: Make sure the bottom of the gate frame
remains completely flat on the floor.
Next, tighten both of the Tension Knobs at the top at
the same time by turning them clockwise (5C).
6. Tighten the Tension Knobs until the two Indicator
Lines, located on the Upper Locking Set and on the
Right Upper Corner, align horizontally (6A).
5A
5C
Tighten
inward
Gate frame Tension knob
Tighten inward and align the Indicator Lines
Indicator
Lines
Keep this gap about
1mm (0.04in)
6A
When correctly tightened, the distances
between Tension Knobs and Rubber Pads
should be equal (6B, 6C).
Note: When first installing, the gate will have
this gap. This is normal and will disappear
when gate is completely installed.
Tighten
inward
Tighten
inward
5B

6
7. To open the gate: Slide the Gate Release Switch (7A). Lift the Gate Panel upward (7B). Gate swings open
in both directions (7C).
OPERATION
Lift Gate Panel
up to open
Gate Release
Switch
Slide Gate opens in
both directions
7A 7B 7C
8. To close the gate: Release the Gate and it will swing closed automatically.
Try this action several times and make sure:
• The Upper Lock Rod and the latch of the Switch are completely latched within the Lock Holder at
Right Upper Corner (8A).
• The Lower Lock Rod of the Gate Panel fits securely into the Lock Holder of Gate Frame (8B).
• The Warning Line has disappeared (8C & 8D).
Gate
Panel
Lock
Holder Gate Frame
Right Upper
Corner
Upper
Lock Rod
Lock Holder
8A
Lower
Lock
Rod
8B
Warning line
8C
8D
The warning line will disappear when the gate is locked properly.
The warning line will appear RED color if the gate is opened or not locked properly.
RED

7
9. For easy walk through use Smart Stay Open System:
To engage the Smart Stay Open System swing gate in chosen direction to its maximum opening (9A).
Gate will stay open. Close as required.
Caution: When using the Stay Open System, the automatic closing feature is not in operation.
Keep gate closed when children are present.
Gate in CLOSED position
Swing to OPEN positions
TOP VIEW OF GATE
9A

8
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to
statutory consumer guarantees and does not seek to exclude
or limit them. These guarantees include that Tee-Zed’s
products are of acceptable quality. This Tee-Zed product is for
the specific purpose detailed in the instructions and
packaging and Tee-Zed considers use outside of that purpose
to be abnormal use. To the maximum extent permitted by
law, Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other
than in accordance with the supplied installation and
removal instructions; or
• arising under the law of tort or contract.
MAINTENANCE & CARE
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check gate to ensure it is fitted properly and securely. Adjust as required.
• Regularly check tension knobs and rubber pads to make sure the gate is securely in place.
• Do not use the safety gate if any components are damaged or missing.
• To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water.
Never clean with abrasive, ammonia based bleach based or spirit type cleaners.
• If the gate does not stay in position or does not swing closed properly, the gate may not be
installed properly.
Remove and re-install gate, make sure the gate is installed vertically.
• Indicator Lines must be correctly aligned. Keep 1mm (0.04in) gap.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
Made in Dongguan, China.
©2015 Tee-Zed Products Pty Ltd
Tee-Zed Products Pty Ltd,
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: [phone]
[e-mail]
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre, Auckland
New Zealand Tel: [phone]
[e-mail]
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: [phone]
[e-mail]
Dreambaby
®
products by
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
www.youtube.com/dreambabytv
www.facebook.com/dreambabysafety
www.twitter.com/dreambabysafety