dreambaby Liberty Security Gate Kit F776 User manual

F776
WARNING
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING — Incorrect installation can be dangerous;
WARNING — Do not use the safety barrier if any components are damaged or missing;
WARNING — The safety barrier must not be fitted across windows;
WARNING — Never use without mounting cups;
This safety gate is for domestic use only;
This safety gate has been designed for use with children up to 24 months of age;
Never use with a child able to climb over or dislodge/open the gate;
The surfaces that the gate is to be fixed to must be suitable for the purpose and must be structurally sound;
If the barrier is to be used at the top of the stairs, it should not be positioned
below top level;
If the gate is to be used at the top of the stairs to prevent the child falling down the stairs, it must not be placed
on any stair below the level of the top stair;
This gate has a manual close system;
This gate is intended for indoor use and is not to be exposed to outdoor elements;
Install this gate away from heaters and other sources of heat.
Caution: As part of the pressure-mounted gate engineering, there is a construction bar at the base of the gate
opening. To avoid tripping or falling, always use extra caution to step over this construction bar at the base of
the gate, particularly when gate is positioned at the top of a staircase.
Can be used in conjunction with a Dreambaby® Watch-the-Step® Gate Ramp (F837) to help avoid tripping.
F776 IM_v4_022016
1
If you sell or give away this product, make sure you give this instruction to the new owner.
This safety gate complies with EN1930:2011
F776 fits openings 93cm.
INSTRUCTIONS
Liberty Security Gate Kit
With Stay-Open Feature & Additional 9cm Extension

PARTS LIST
A - Gate Panel
B - Upper Locking Set
C - Gate Release Switch
D - Smart Open-Hold System
E - Right Upper Corner
F - Tension Knobs
G - Bolts with Rubber Pads
H - Mounting Cups
I - Double-sided Adhesive Tape
J - Gate Frame
K - Lower Locking Set
L - Gate Extension Frame
M - Extension Pins
WARNING: This package contains
small parts and sharp points in an
unassembled state. Keep out of reach
of children. Adult assembly required.
F x 4
I x 4
G x 4
H x 4
x 4
M x 2
M
DBC
A
F
G
H
I
J
K
L
E
2
THE GAP IN THIS GATE IS NOT A FAULT.
THE GAP WILL DISAPPEAR WHEN THE GATE IS
CORRECTLY INSTALLED.
NOTICE TO CUSTOMERS
IMPORTANT NOTICE
to Customers
The gap in this gate is NOT a fault.
The gap will disappear when the
gate is correctly installed.
Refer to enclosed instructions for
correct installation procedures.
F - Gate Notice

3
Gate
INSTALLATION
Ensure the surface you are mount the gate is structurally sound such
as solid timber, brick or masonry.
For plaster / gyprock surface, locate the timber beam or stud behind
and mount in this location (mounting on plaster / gyprock alone is not
strong enough and not safe). Do not mount to glass.
+F901
9cm
F776 gate
75-84cm
INCLUDED IN THIS KIT:
F776 gate plus 1x F901 - 9cm Extension
Fits openings up to 93cm
1. Measure the width of the opening of where you intend to install the gate.
For openings over 93cm select the appropriate Gate Extension(s), sold
separately. Some examples are shown below.
75 - 84cm 184 - 193cm
F776
gate only
+ F901F1959 + F776
gate only

*F901 - 9cm
F902 - 18cm
F903 - 27cm
F1951 - 36cm
F1953 - 45cm
F1955 - 54cm
F1957 - 63cm
F1959 - 100cm
Gate Extensions
(sold separately)
*
For 9cm Gate Extensions For all other Gate Extensions
Tension
Knob
Insert LONG END of
EXTENSION PIN
into Gate Frame
Gate
Extension
9cm
Gate Frame
NOTE: Wider gate extensions can
be used on the F776 gate section.
Replace the included 9cm gate
extensions with larger options,
listed below under Gate Extensions
(sold separately).
2A 2B
+F901
9cm
F776 gate only
75-84cm
Extension Frame
Gate Frame
Tension
Bolt
Tension Knob with
Rubber Pads
Extension Pin
Tension
Knob
Insert SHORT END of
EXTENSION PIN
into Gate Frame
Gate
Extension
27cm
Gate Frame
Insert Extension Pins into the holes on the outside of the Gate Frame (2A / 2B).
Next, slip Extension Frames over the Pins.
Finally, slide in the Tension Knobs and Bolts with Rubber Pads.
A maximum of 2 Gate Extensions can be used,
1 on each side of gate. Do NOT install 2 Gate Extensions on the same side of gate.
WARNING
2. To use with Gate Extensions.
4

5
3B
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely flat on the
floor (3A), and it is perpendicular to the openings and the floor (3B & 3C).
4. Then fasten the Mounting Cups to the wall with screws or double-sided adhesive tape (4A).
Note: Ensure that they are aligned vertically, so that the Mounting Cups at the top are
directly above the ones at the bottom (4B).
5. For use on stairs (5A & 5B).
Top view of gate
3C
Side view of gate
floor floorfloor
Fasten Mounting Cups to the wall with
screws or double-sided adhesive tape.
3A
G x 4J x 4
If the gate is used at the
bottom of the stairs to
prevent the child from
climbing up the stairs, it
must be placed on the
lowest stair.
If the gate is to be used
at the top of the stairs to
prevent the child from
falling down the stairs, it
must not be placed on
any stair below the level
of the top stair.
Bottom of stairs Top of stairs
G x 4J x 4
5A
6. Partially slide the Bolts with Rubber Pads and Tension Knobs outwards (6A) from the Gate Frame /
Extension Frames into Mounting Cups (6B).
Screw in Mounting Cups
when using gate on stairs
6A 6B
4
4B
5B
4A

Tighten inward
Tighten inward and
align the arrows
Tension
Knob
Gate
Frame
Keep this gap about 1mm
8B
8C
7A
8A
7C
7B
6
7. Tighten both of the bottom Tension Knobs (7A) by
turning them clockwise at the same time (7B & 7C).
NOTE: Make sure the bottom of the gate frame
remains completely flat on the floor.
Next, tighten both of the Tension Knobs at the top at
the same time by turning them clockwise (7C).
Tighten
inward
Note: When first installing, the gate will have this gap. This is
normal and will disappear when gate is completely installed.
8. Tighten the Tension Knobs until the two Arrows,
located on the Upper Locking Set and on the
Right Upper Corner, align horizontally (8A).
When correctly tightened, the distances
between Tension Knobs and Rubber Pads
should be equal (8B, 8C).
Distance should be equal
Distance should be equal

Lift Gate Panel up
to open
9. To open the gate: Slide the Gate Release Switch (9A). Lift the Gate Panel upward (9B).
Gate open in both directions (9C).
9B
Gate Release
Switch
Slide
9A
Gate opens in
both directions
9C
Gate
Panel
Lower
Locking Set Gate Frame
10A 10B
OPERATION
7
10. Close the gate until it is fully locked with Upper (10A) and Lower Locking sets (10B) engaged.
Lower
Lock
Rod
Upper
Locking Set

Gate in CLOSED position
Swing to OPEN positions
TOP VIEW OF GATE
MAINTENANCE & CARE
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check Tension Knobs, Rubber Pads and Mounting Cups to make sure
the gate is securely in place and closes correctly. Adjust as required.
• Only use Dreambaby
®
spare parts. Any additional and replacement parts should
be obtained from Tee-Zed Products.
• To clean, wipe surface with a damp cloth using mild detergent and warm water.
Never clean with abrasive, ammonia, bleach or spirit based type cleaners.
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to statutory
consumer guarantees and does not seek to exclude or limit them. These
guarantees include that Tee-Zed’s products are of acceptable quality.
This Tee-Zed product is for the specific purpose detailed in the
instructions and packaging and Tee-Zed considers use outside of that
purpose to be abnormal use. To the maximum extent permitted by law,
Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in
accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
Dreambaby
®
products by
Made in Hangzhou, Zhejiang, China.
©2016 Tee-Zed Products Pty Ltd
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
facebook.com/Dreambabysafety
youtube.com/user/Dreambabytv
Tee-Zed Products Pty Ltd
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: [phone]
[e-mail]
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre Auckland
New Zealand Tel: [phone]
[e-mail]
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: [phone]
[e-mail]
8
11. For easy walk through use Smart Stay Open System:
To engage the Smart Stay Open System swing gate in chosen direction to its maximum opening (11A).
Gate will stay open (11B, 11C). Close as required (11D).
Caution: When using the Stay Open System, the automatic closing feature is not in operation.
Keep gate closed when children are present.
11A
11B 11C
11D