Dreamline AQUA SWING User manual

“AQUA SWING” VER 1 REV 2 11/2015
1
AQUA SWING
SHOWER DOOR INSTALLATION INSTRUCTIONS
IMPORTANT
DreamLine®reserves the right to alter, modify or redesign products at any time without
prior notice. For the latest up-to-date technical drawings, manuals or additional details
please refer to your model’s web page on DreamLine.com.
Please read these instructions carefully before installing. If you have any questions
regarding installation, please contact our technical support specialists Monday
through Friday 8:00 AM –7:00 PM EST at Phone: [phone],
Fax: [phone] or e-mail our technical support group at
[e-mail]
For more information about DreamLine®products please visit DreamLine.com
Left hand installation shown

“AQUA SWING” VER 1 REV 2 11/2015
2
Preparation
1. Prior to installation, examine all boxes and packages for shipping damage and compare the
piece count with your packing slip. After opening all boxes and packages read this
introduction carefully. Check that all of the needed parts are included in the package by
checking off the components on the “Detailed Diagram of Shower Door Components”. If the
unit has been damaged, has a finishing defect, or has missing parts, please contact our
customer support department within 3 business days of the delivery date. Please note that
DreamLine®will not replace any damaged products or missing parts free of charge after
3 business days or if the product has been installed. Feel free to contact DreamLine®if you
have any questions, and please provide an order number, job name or other proof of purchase
to help us identify your original order.
2. Please note that you should consult your local building codes with questions on
installation compliance standards. Building and plumbing codes may vary by location,
and DreamLine®is not responsible for code compliance standards for your project and
will not accept any returns.
3. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and
will be able to support the total weight of the unit. Also make sure the walls are at right angles.
Irregular installation surface level or improper angle of side walls will result in serious problems
for your installation. Please, note that some adjustments and drilling might be necessary
during the installation process.
4. This model has 3/8” of adjustment for out-of-plumb wall conditions within the wall
profiles.
Tools Required

“AQUA SWING” VER 1 REV 2 11/2015
3
Detailed Diagram of Shower door Components
03
04
05
06
07
08
09
10
01
02
11
Packing list
01
Wall profile
1pc
07
Threshold connector (left/right)
1set
02
Glass door with Hinged glass profile
1set
08
Aluminum threshold
1pc
03
Wall anchor
4pcs
09
Bottom anti-water strip
1pc
04
Big head screw ST4.2×55
4pcs
10
Threshold end cover (left/right)
1set
05
Round head screw ST4.2×16
3pcs
11
Handle
1pc
06
Decorative plug and washer
3sets
NOTE: Unpack your unit carefully and inspect it. Identify all parts using the detailed diagram and
packing list in this manual as a reference. Before discarding the carton, check for small hardware
bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please contact
DreamLine®for replacement. The shipping boxes may contain extra parts not used in your model
configuration.
NOTE: Retain these installation instructions for future reference.

“AQUA SWING” VER 1 REV 2 11/2015
4
Shower door installation
1. Prepare your finished opening for installation.
Clean all surfaces and remove any debris or
construction materials. See Fig 1.
2. Using a level, position the Wall profile (01)
on the tub deck and against the wall, in line
with your threshold/tub deck. This unit
requires 1” of flat threshold space for
installation
See Fig 2.
Fig 2
Fig 1
NOTE: This model is reversible for left or
right hand installation. This manual will
show the left hand installation. For a
right hand installation, simply begin on
the opposite wall and reverse the
orientation of the parts as necessary.

“AQUA SWING” VER 1 REV 2 11/2015
5
3. Mark the drill holes on the wall through the
predrilled holes in the Wall profile (01).
Now drill holes in the wall using a Φ5/16 drill
bit and insert the Wall anchors (03).
Apply silicone along the back of the Wall profile
and into the drill holes. Fasten the Wall profile
to the wall with the Big head Screw ST4.2x40 (04).
See Fig 3.
4. Slide the assembled Glass door with
Hinged glass profile (02) into the groove of the
Wall profile (01) and level it vertically (Fig 4.3).
Make final adjustment (up to 1/2”) if required
keeping the door glass level. Drill the holes
through the first layer of the Wall profile (01)
and into the Hinged glass profile using an Φ1/8
drill bit.
Secure the Wall profile and the Hinged
Glass profile with the Round head screws
ST4.2x16 (05) and washers. Cover the screw
heads with the Decorative Covers (06).
See Fig 4.
1
2
3
4
5
Φ8mm
Φ5/16”
Fig 3
1
2
3
4
5
6
Φ3mm
Φ1/8”
Fig 4
inside
Check the
installed door
glass for level
inside

“AQUA SWING” VER 1 REV 2 11/2015
6
5. Snap the Aluminum threshold (08) into
the Threshold connector (07) and
Threshold end cover (10).
Left hand installation shown
Run a bead of Waterproof silicone along
the bottom of the Aluminum threshold. Attach
the Aluminum threshold onto the tub,
parallel to the tub edge with the
Threshold connector tight to the bottom
and even with the outside of the Hinged glass
profile (Fig. 5.4). Run a bead of Waterproof
silicone along the connection of the Threshold
connector and Hinged glass profile.
See Fig 5.
6. After the silicone fully sets, attach the
Bottom anti-water strip (09) to the
bottom edge of the Glass door.
See Fig 6.
7. Mount the Handle (11) onto the outside of the
Glass door (02). See Fig 7 and Fig 8.
Fig 5
1
4
5
2
2
1
Fig 5
Fig 6
Fig 7
3
Note: Allow the silicone to fully cure
before operating the door to prevent
dislodging the threshold from the tub
deck. You may even consider using
painter’s tape or similar to hold the
threshold tightly in place while it sets.
outside
outside
outside

“AQUA SWING” VER 1 REV 2 11/2015
7
8. Allow 24 hours for the silicone to fully cure
before using your new shower.
See Fig 9 and See Fig 10.
24 H
24 h
Fig 8
Fig 9
Fig 10

“AQUA SWING” VER 1 REV 2 11/2015
8
Product Maintenance
BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after
each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream
based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or
dull the surface.
GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use
with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent
soap buildup and water spots. To prevent scratching the surface: never use abrasive cleaners
and cleaning products that contain scouring agents. Never use bristle brushes or abrasive
sponges.
HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft
cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If
accidentally used, rinse the surface as soon as possible to prevent finish peeling or corrosion.
After cleaning the polished finishes, rinse thoroughly and wipe dry with soft cloth. Never use an
abrasive sponges or cloth, steel wool or wired brushes as these may permanently scratch the
surface.

“AQUA SWING” VER 1 REV 2 11/2015
9
TEL: [phone]
FAX: [phone]
DREAMLINE.COM
For more information on DreamLine®Shower Doors and Enclosures please visit DreamLine.com