Drinkpod DP-RO-PRO User manual

www.drinkpod.com

INSTRUCTIONS
1.Function ------------------------------------------------------------------------------------------
2.Instructions --------------------------------------------------------------------------------------
3.Schedule of filter change --------------------------------------------------------------------
4.Core change guide ----------------------------------------------------------------------------
5.Process flow chart of water production --------------------------------------------------
6.Electrical schematic diagram ---------------------------------------------------------------
7.Installation hint ---------------------------------------------------------------------------------
8.Technical parameters ------------------------------------------------------------------------
9.Matters needing attention -------------------------------------------------------------------
10.lt is recommended to replace the periodic table for key components ----------
1
1
4
5
6
6
7
8
8
9

plush
purify
RO
PCT
Component Chart:
1
Reverse Osmosis
(RO) System
Faucet Power Adapter
Saddel Valv TubesConnectors
Blue Collar Clip TPFE/Teflon Tape Valve Adapter 1 Valve Adapter 2
SCAN HERE FOR
REPLACEMENT
FILTERS

Reset button:
When the water purifier is working, press and hold the "Reset" button for 3
seconds to enter the filter element reset program, and then tap "Reset"key
to select the corresponding filter element, the icon of the selected filter
element flashes (with an alarm sound), and the selected filter element needs
to be reset.After the filter element, press the reset button for 3 seconds,
the corresponding filter element life will be reset (accompanied by an alarm
sound), and the filter element reset is completed.bit manipulation. If there is
no operation for 10 seconds, exit the reset procedure.
Flush key:
A: The accumulative water production is more than 30 minutes, no flushing,
automatic flushing for 18 seconds when full of water.
B: The whole machine is powered on, and it will automatically flush for 30
seconds.
C: Press the "Rinse" button for 3 seconds, it will automatically rinse for 30
seconds; during rinse, the 3 indicator lights will flash one by one within
1 second.
D: Continuous standby for 6 hours, no flushing in between, automatic
flushing for 18 seconds.
Water production status:
The system detects that the high pressure switch is closed and immediately
produces water, the water production indicator flashes, and other icons are
always on.
Full water (standby) state:
When the system detects that the high-pressure switch is disconnected,
it will be filled with water immediately, the water production light will be on,
and other icons will be on.
Filter life:
The "PCT" filter element corresponding to the indicator light is
No. 1/3 filter element, and "RO" corresponds to No. 2 filter element.White
is always on during the cycle. When the remaining total life is 10%, the
indicator light corresponding to the filter element flashes in white, and the
filter elementWhen the accumulation reaches the set value, the indicator
light corresponding to the filter element is always on in red, accompanied
by an alarm (every half an hour,Alarm 10 times, once a second).

side
panel
pump
cover
top
coverframe
reverse osmosis
membrane filter
front
panelcover
PCT
composite filter
indicator
board
base
booster
pump
Flush
Solenoid
High voltage
switch
nlet solenoid
valve
3

Filter element type PCT RO
Replacement frequency 8-12 months 12-24 months
4
3. Schedule Of Filter Change
Filter element replacement cycle (it is recommended that the filter element replacement
cycle is as follows:)):
After the filter element of the product is used for a period of time, various impurities will be
accumulated in the filter element, which will affect the effluent speed. In order to maintain
normal effluent, the filter element should be replaced regularly. If the average daily pure
water consumption of municipal tap water is 10 litres on the premise that the raw water
temperature, water pressure and water quality of municipal tap water are in accordance with
this specification, the replacement cycle of each filter element is as follows:
Note: the water quality has a great influence on the life of the filter element, and the service
life of the reverse osmosis membrane and other filter elements is affected by many factors.
In the actual use process, due to the different water quality, its life may be lower than the
above data, this data is only for reference.
In general, if the following circumstances occur, you should consider replacing the filter
element:
When the quality of the effluent is poor and the taste decreases,
The effluent flow is obviously reduced, check whether the filter element or membrane is
blocked (it should be determined that it is not caused by the drop in water temperature).
The filter element is seriously blocked, so that the water purifier can not make water or
clean water can not flow out.

4.Core change guide
Warm reminder: please cut off the water source and turn on the faucet to relieve pressure
before changing the filter element.
The whole machine runs for 3-5 minutes, and then the power is cut off.
A small amount of residual water will flow out when the filter element is replaced.
First, remove the old filter element.
The first step: cut off the water and power according to the warm reminder.
The second step: first remove the cover plate, select the filter element to be replaced and
rotate the filter element counterclockwise by hand, and remove the filter element when
the filter element is marked" "at" " (as shown in figure 1).
Step 3: remove the filter element and use a clean towel to clean the remaining water in
the frame filter cartridge.

light display faucet
reverse osmosis
membrane filter
composite filter
light display faucet

7
Debugging method.
1. After the installation of the whole machine is completed, open the three-way ball valve,
check that there is no water leakage between the whole machine and other joints, and turn
on the power supply.
2. Turn on the faucet and wash the reverse osmosis membrane filter element; in order to
make the reverse osmosis membrane filter element have the best purification effect, please.
Consumers follow these steps:
1) turn on the pure water faucet and make water normally for 1 hour; 2) turn off the tap and
let the whole machine sit for 24 hours.
3) turn on the pure water faucet, and after 1 hour of normal water production, the produced
water can be drunk directly.

Product Name.
Voltage / freque ncy.
Rated power.
Ap plicab le water pressure.
Clean water flow.
Rated total net water.
Anti-e lectric shoc k type.
Ap plicab le e nvironment.
Reverse osmosis water pur ifier.
110V / 50 Hz.
90W.
0.1MPa-0.4MPa.
95L/ H.
4000L.
Class II.
Ambient temperature 5 °C-45 °C,
relative humi di ty s 90% (i ndoor).
Ap plicab le water Temperature 5 °C-38 °C.
Ap plicab le water quality. Mu nicipal tap water.
Product size. 433 x 137 x 405mm
8.Technical parameters
8
9.Matters needing attention
This product must use the new hose assembly Iha! comes with it, and lhe old hose
assembly cannot be reused.
In view of the particularity of clean aquatic products, all the components thal make up this
product have a certain service life, in which lhe recommendations of key components are
described in detail in this manual, "key components suggest replacement of periodic table".
Please carry out replacement, daily inspection and maintenance in slricl accordance wilh
the requirements of this manual.
1. When the product breaks down, please cut off lhe water and power quickly, and call our
national service hotline in time lo gel in touch with the official after-sales.
The applicable voltage of lhe power adapter equipped with this product is 1 DOV, 240V,
50x60Hz. In order to ensure the safely of the product, be sure lo use the special power
adapter of our company.
If lhe power assembly is damaged, in order to avoid danger, the entire component must be
replaced by professionals from the company's maintenance department or similar
department.
2. The waler source of this product is municipal white waler, the range of waler pressure is
0.1 MPA, the waler temperature is 5 °C-38 °C, and the global temperature is 5 °C-45 °C. It is
• All the parameters related to the performance of this product are the test results
under the standard test conditions, and will change with the different use conditions in
the actual use process.

9
Serial number. Component category. Component name. Recommended replacement
cycle (month)
1 Pressure container. Filter element filter shell. 36
2 The power adapter. 60
3 Intake solenoid valve. 30
4 Electronic Flushing solenoid valve. 48
5 control class. High voltage switch. 30
6 Booster pump. 60
7 Indicator board. 60
8 PE tube. 30
9 Other Joint. 36
10 accessories SealinQ rinQ. 36
11 Faucet 60
10.lt is recommended to replace the periodic table for key
components.
strictly forbidden lo use beyond the range.
3. This product is only suitable for indoor installation, and there should be reliable ground
gushing within 1.5 meters around the installation, so as lo avoid the loss caused by waler
leakage caused by poor batch water.
4. When the product is not used or left unattended for more than 3 days, please cul off the
power and waler source to prevent the "water hammer" impact caused by unstable water
pressure, causing damage or gushing of the product, and when you use it again, it is
recommended thal the direct drinking water produced in the first few minutes should be
discharged, otherwise it will affect !he lasle. 7. Avoid installation in direct sunlight and
outdoor places, sunlight exposure will accelerate the aging of lhe machine shell and affect
the safely performance of the machine.
5. Do not install or expose the product lo lhe environment below 0 °C, so as lo avoid the
rupture of lhe internal pipeline due lo the expansion of waler ice.
6. You should not store flammable, explosive or heal-prone articles near the machine to
avoid danger.
Please use the authentic filler elements and accessories provided by our company to
ensure the normal use of the products, otherwise the company will not be responsible for
the warranty.
The company will not bear any responsibility for the consequences caused by failure to
comply with the above precautions.

www.drinkpod.com
888 852 7873