DRYSPEC H35 Top Load Liner User manual

Instruction Rev01
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DrySpec
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2551 or visit WWW.DRYSPEC.COM
Please Read Before Installing
DRYSPEC products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
What’s In The Box?
DRYSPEC.COM
Instruction Manual
(a) Top Load Liner.....................................................................Qty 1
(b) Webbing Frame...................................................................Qty 4
(c) Self Tapping Screw.............................................................Qty 10
(b) Lid Stay.............................................................................Qty 2
Kit Contents
(a)
(d)
(c)
(b)
H35 Top Load Liner
DSL.H35.10300

2. Top Load Liner Installation & Operation
1.1 - Installing The Lid Stays
The DrySpec Top Load Liner transforms a side loading H35 case into top loading
luggage. This padded, semi-rigid liner with its high density polyethylene core and a
durable nylon shell, mounts to the inside and lid of your H35 case providing a pocket
that swings out when opened.
Step One: Use the Self Tapping Screws (c) to install the Lid Stays (d) to the mounting
points illustrated above.
DRYSPEC.COM
1.2 - Installing The Strap Bars
Step One: Use the Self Tapping Screws (c) to install the Strap Bars (b) to the lid using
the mounting points illustrated above.
1.3 - Securing The Top Load Liner
Step One: Fold the Top Load Liner into shape and secure the velcro strips where the
panels meet.
Step Two: Connect each of the four straps to the Strap Bars (b) and tightly secure each
strap to the mating velcro patch on the Top Load Liner.
1.4 - Lid Stay Operation
The Lid Stay keeps your case partially opened when engaged.
Step One: To fully open the case simply pull down and outwards on the release so that
the Top Load Liner can swing past the Lid Stays (d).
Lid Stay Screw
Webbing Frame
Screw
Strap Bar
Velcro
Strap
Lid Stay
Release