DSE RH Series User manual

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:1
DSE SRL - ITALY - WWW.DSE.EU
RH-xxx
Fixed IP cameras
RH-SDxxx
Motorized IP cameras
RH2-xxx
720P IP cameras

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:2
DSE SRL - ITALY - WWW.DSE.EU
Introduction
The RH series consists of IP network cameras based on ONVIF protocol with resolution from
HD720P, up to 4K.
The units connect to a LAN via the RJ45 port like a computer or other network unit and the
images are displayed on the PCs on the network using an Internet browser (IE, Chrome, Safari
etc.) or special recording programs. DSE SMARTLIVE applications for access with iPhone, iPad
and Android smartphones are also available on the APP STORE and GOOGLE PLAY.
The power supply is possible with 12VDC adapters or through the same
network cable thanks to the Power over Ethernet (POE) technology
supported by all cameras except for the speed-dome and wifi models.
The use of the best SONY C-MOS sensors guarantees image quality in all
light conditions and during infrared shooting.
The megapixel resolution allows an image detail that cannot be reached with analog systems
and the 16: 9 format, now a consolidated television standard, represents
the new dimension of video surveillance, ideal for viewing on a PC
monitor or wide screen TV.
The RH series network equipment uses H.265 Hi-Profile compression, a
recent evolution in MPEG4 digital compression, used for example
in Blu-ray discs for maximum video fidelity. The RH Series
cameras fully support the international ONVIF protocol and are
compatible with any multi-protocol IP recording software or
network video recorder (NVR) capable of handling this standard.
The cameras also support the RTSP protocol for streaming video
to clients using this standard.
Network recording software for Windows XP / Vista / 7/8/10 capable of connecting up to 128
cameras and utilities for network configuration is included with each camera. SDK (Software
Development Kit) is available for developers for the development of their own applications
capable of interacting with cameras and ActiveX APIs to control the cameras via the web with
their own graphic interfaces.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:3
DSE SRL - ITALY - WWW.DSE.EU
Installation
RH-TCC1- Box room
CHOICE OF OBJECTIVE
The camera is supplied without a lens. It is possible to combine all DSE VARIFOCAL lenses. For
optimal results, you need to choose megapixel lenses capable of supporting the resolution of
the camera (Ref. OM-xxxx). Also if you plan to use it with infrared illuminators use lenses with
IR correction (Ref. XxxxxxxIR)
MOUNTING THE OBJECTIVE
The camera body is equipped with a rotating ring nut to adjust the position of the optical
sensor. In this way it is possible to focus on any type of lens without having to use spacer rings.
Once the lens is screwed in, adjust the focus. The camera is equipped with an analog BNC
video output to be able to connect a small portable monitor and adjust the focus on the spot.
Act by rotating the adjustment ring if you cannot get a perfectly focused image with the only
focus of the lens.
USE OF AUTOIRIS OBJECTIVES
The camera allows you to use fixed, manual and automatic iris lenses. In the latter case the
autoiris lens is equipped with a connector to be connected to the camera body. The camera is
compatible with all DC drive auto-iris lenses with the following connection connections.
Video A.D
1 NC Control +
2 VCC Control-
3 GND Drive-
4 Video Drive +

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:4
DSE SRL - ITALY - WWW.DSE.EU
REAR CONNECTIONS
 AUDIO IN - MICROPHONE IN - The camera is equipped with a built-in microphone however a
3.5 mm minijack is available to connect an external microphone. The choice between the two
sources is made in configuration. (Impedance 1 KOhm). Any microphone can be connected
to the audio input as long as it has its own independent power supply, such as our RE-CM3
model. Microphones cannot be connected without power, such as computer microphones.
A standard stereo mini-jack like the one shown below is used for connection.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:5
DSE SRL - ITALY - WWW.DSE.EU
If you need to assemble the connecting cable between the microphone and the camera
yourself, remember to connect the stocking of the 2 video cables to the first segment near
the connector body and the 2 video signals to the remaining two segments in the center and
at the end of the connector. It is possible to connect the microphone to any of the connectors
as the camera manages audio in mono and not stereo format.
 AUDIO OUT - This 3.5mm jack allows you to connect local speakers. This function allows you
to create a two-way audio conversation between the person in front of the camera and the
operator in front of the client PC. (Upper impedance 16 Ohm)
 SLOT Micro SD CARD - Slot to insert a Micro SD card (max 32GB) to save images on the same
camera.
 12VDC - Plug to connect the 220VAC / 12VDC power supply (not included). Alternatively, it
is possible to power the camera in POE directly from the network if the network switch
supports this functionality.
 NIC (NETWORK) RJ45 - RJ45 FEMALE connector to connect the network. For connection to a
HUB or network switch use a normal LAN cable. To connect only one PC directly, use a
crossover cable.
 RS485 - This port allows you to connect external units such as pan / tilt or speed dome
cameras to control them via the camera's web interface. Supported protocols Pelco P / D.
 ALARM IN / OUT - An input with a voltage between 5 and 12VDC can be connected to the
alarm input between the IN and COM terminals. During programming it is possible to define
whether the alarm is considered to be present or in the absence of voltage. The alarm output
is used to operate external devices such as horns or lights. The contact is of the ON / OFF
type with a maximum directly controllable load of 300mA at 12VDC. During programming it
is possible to set the operation (NO / NC), any intermittence, and the activation duration in
the event of an alarm.
Example of output connection

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:6
DSE SRL - ITALY - WWW.DSE.EU
Example of input connection
 VIDEO OUT - BNC output for connecting analog monitors. For example, it allows you to
connect a portable monitor so that you can focus on the lens comfortably after mounting.
ATTENTION: this output may not be active if disabled in the camera configuration.
 RESET - Button to reset the factory parameters. Press and hold for at least 5 seconds to
restore factory settings including network data.
MOUNTING THE CAMERA
If installed indoors, the camera can be fixed to the wall with a camera bracket such as RE-ST2L.
For outdoor installation, a protective housing such as RE-C3 must be used.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:7
DSE SRL - ITALY - WWW.DSE.EU
RH-BCC1xxx- Waterproof camera with IR up to 80 m.
OBJECTIVE ADJUSTMENT
The camera is equipped with an adjustable lens to allow perfect adjustment of the area to be
framed. The camera body is equipped with two screws to adjust the focal (ZOOM) and focus
(FOCUS) placed in the lower part of the camera or with a motorized lens. There is also a local
analog video output with RCA connector placed behind the watertight door on the lower side
of the camera. This output can be used to connect a monitor locally and to adjust the lens in
the actual operating position of the camera.
In manual cameras it is necessary to adjust the framed area with the focal screw and then act
on the focus screw to optimize vision.
CONNECTIONS
The connections are placed at the end of the cable that comes out of the camera body. The cable
with the connections is 40 cm long and is used to reach a protected box to be arranged so as to
house the connectors inside.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:8
DSE SRL - ITALY - WWW.DSE.EU
 RJ45 (NETWORK) (1) - MALE RJ45 connector to connect the network.
For connection to a HUB or network switch use a normal LAN cable.
To connect only one PC directly, use a crossover cable. The RJ45
female-female adapter is provided to connect a cable with a male
connector.
 AUDIO IN (2) - MICROPHONE INPUT - The camera is equipped with
a female RCA connector to connect an external microphone. (Impedance 1 KOhm)
 AUDIO OUT (3) - The camera is equipped with a female RCA connector which allows you to
connect local speakers. This function allows you to create a two-way audio conversation
between the person in front of the camera and the operator in front of the client PC. (Upper
impedance 16 Ohm)
 12VDC (4) - Removable 2-place terminal block to connect the 220VAC / 12VDC power supply
(not included). Alternatively, it is possible to power the camera in POE directly from the
network if the network switch supports this functionality.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:9
DSE SRL - ITALY - WWW.DSE.EU
 ZOOM ADJUSTMENT (1) - Adjusts the focal length from 2.8 to 12 mm
 FOCUS ADJUSTMENT (2) - Adjusts the focus
 SLOT Micro SD CARD (3) - The slot to insert a Micro SD card (max 64GB) to save images on
the same camera is located behind the watertight door located on the bottom side of the
camera.
 VIDEO OUT (5) - There is a female RCA output for connecting analog monitors. For example,
it allows you to connect a portable monitor so that you can focus on the lens after mounting.
The connector is located behind the watertight door located on the underside of the camera.
ATTENTION: this output may not be active if disabled in the camera configuration.
 RESET (7) - The button to reset the factory parameters, including the network parameters,
is placedbehind the watertight door located on the underside of the camera. Press and hold
for at least 5 seconds to restore factory settings including network data.
 RED LED (4) -Placed behind the watertight door on the lower side of the camera, it indicates
the correct power supply of the camera with external 12VDC power supply
 YELLOW LED (6) -Placed behind the watertight door on the underside of the camera, it
indicates the correct dialogue with the network switch.
MOUNTING THE CAMERA
The camera has a waterproof container that allows it to be installed outdoors without protections.

INSTALLATION MANUAL
RH SERIES - ONVIF IP CAMERAS
Page:10
DSE SRL - ITALY - WWW.DSE.EU
A metal fixing ring is supplied with the camera to be fixed to the wall with 4 anchors (supplied)
using the drilling template included in the package. The word TOP is indicated on the ring to
indicate the side to be held up. On this ring, firmly anchored to the wall, the camera bracket is
screwed with 4 screws always respecting the word TOP so that the lateral cable exit slot remains
downwards. The cables can pass behind the bracket or exit laterally through the slot in the
bracket.
Pay attention to the gasket placed on the fixing disk which must remain in position in its seat
during the fixing of the bracket to guarantee the impermeability.
The camera bracket is equipped with 3 ABC star screws (key supplied) which must be loosened
to allow orientation on the 3 axes. Once the camera is correctly oriented, it is necessary to
retighten them fully. Finally adjust the sun visor with screw D