DTS SLICE6 DAS User manual













 
 
 
 


                               

              
                 
SLICE6 AIR DAS Extension Cable
SLICE6 AIR
13006-9047x-R-ASY
0
of 2
13006-9047x-R-ASY.docx
26 JUN 2019
JW
---
DS
---
REVISIONS
REV
DESCRIPTION
DATE
APPR
0
INITIAL RELEASE
27 JUN 2019
DS
Key
Function
80000-01263-R
180-026-103L001
+
80000-01109-R
979-015-030R121
70005-00036-R
3M 3600B/26
(SEE ROUTING FOR LENGTH)
SOLID (STRIPE)
80000-01264-R
180-026-203L001
+
80000-01109-R
979-015-030R121
White Printable
Heat Shrink
VDC INPUT
PIN 1
BLK with (RED)
SCKT 1
-
TX1P
PIN 2
BLK with (BLU)
SCKT 2
-
TX1N
PIN 3
BLU with (BLK)
SCKT 3
-
RX1P
PIN 4
BLK with (ORG)
SCKT 4
-
RX1N
PIN 5
ORG with (BLK)
SCKT 5
-
TX2P
PIN 6
RED with (WHT)
SCKT 6
-
TX2N
PIN 7
WHT with (RED)
SCKT 7
-
RX2P
PIN 8
RED with (YEL)
SCKT 8
-
RX2N
PIN 9
YEL with (RED)
SCKT 9
-
VDC INPUT
PIN 10
RED with (BLK)
SCKT 10
-
VDC INPUT
PIN 11
BLK with (WHT)
SCKT 11
-
GND
PIN 12
BLK with (GRN)
SCKT 12
-
PPS
PIN 13
BLK with (YEL)
SCKT 13
-
START
PIN 14
BLK with (BRN)
SCKT 14
-
UART_TX_P
PIN 15
RED with (GRN
SCKT 15
-
UART_TX_N
PIN 16
GRN with (RED)
SCKT 16
-
UART_RX_P
PIN 17
RED with (BRN)
SCKT 17
-
UART_RX_N
PIN 18
BRN with (RED)
SCKT 18
-
GND
PIN 19
WHT with (BLK)
SCKT 19
-
GND
PIN 20
GRN with (BLK)
SCKT 20
-
GND
PIN 21
YEL with (BLK)
SCKT 21
-
ON
PIN 22
BRN with (BLK)
SCKT 22
-
STATUS
PIN 23
RED with (BLU)
SCKT 23
-
EVENT
PIN 24
BLU with (RED)
SCKT 24
-
IRIG
PIN 25
RED with (ORG)
SCKT 25
-
CASE
PIN 26
ORG with (RED)
SCKT 26
-
1
2
3
4
2
5
Notes:
a. See Sheet 2 for detailed assembly instructions
b. In accordance with IPC/WHMA-A-620 Class requirements; Strip and solder all wires so the insulation
is as close as possible to the solder cups
c. Use RMA or no-clean flux
d. Test appropriately to verify connections per wiring table
e. Apply Label as appropriate; use the actual DTS Part Number
a. See the Production Traveler
Assemble Backshell(s) in accordance with instructions on sheet 2.
5
1
2
SLICE6 AIR DAS Extension Cable (HDD-26 Plug to HDD-26 Socket)
Doc. No. 13006-9047x-R-ASY
1
3
1
5
Add P/N label here
2
2
ROUTING LENGTH ± 2 %
ROUTING LENGTH ± 3%
80000-01264-R
180-026-203L001
FACE VIEW
SOLDER VIEW
4
1
80000-01263-R
180-026-103L001
SOLDER VIEW
FACE VIEW
1













 
 
 
 


                               

               
                 
SLICE6 AIR DAS Extension Cable
SLICE6 AIR
13006-9047x-R-ASY
0
of 2
13006-9047x-R-ASY.docx
26 JUN 2019
JW
---
DS
---
P
Assembly Instructions:
1. Slide 7.37mm strain relief over the end of cable
2. Strip cable jacket ensuring not to damage shielding braid
3. Fold the shielding braid backwards over the end of the strain relief
4. Prevent damage to shield while completing assembly
5. Wire connector as specified in wiring table on sheet 1
6. Remove tape being careful not to break off shielding braid
7. Insert the Jackscrews in the Saddle washers , place the jackscrews into the bottom half of the backshell along with the cable
8. Place the other half of the backshell cover on top ensuring no wires are pinched
9. Sandwich the shielding braid and connected case wires between the two halves of the backshell cover ensuring firm contact
10.Holding the halves together; insert the mounting screws through the holes in opposite directions. Secure the two screws with
included nuts.
i
B
ii
iii
3
iv
CASE AND SHIELD BRAID
CONNECTIONS MUST BE
SECURELY IN CONTACT
WITH BACKSHELL HOUSING
HERE
4
A
i
1
3
iv
ii
iii
2
B
2