DTS TITAN PLUS SOLO User manual

GB
Made in Italy
TITAN PLUS SOLO
User’s Manual rel 2.1
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it

TITAN PLUS SOLO
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
2

DESCRIPTION
TITAN PLUS SOLO is a new range of compact self-contained LED projectors designed for fixed
and mobile installations either indoor or outdoor.
All models are made on aluminium offering high resistance to mechanical stress, and IP20 or
IP65 protection rating.
TITAN PLUS SOLO range features
XLR Male / Female cable
connectors
TITAN PLUS is also available without integrated power supply.
Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each model,
offering different light beam projection angles with even coverage of lighted areas.
TITAN PLUS SOLO can be controlled via any DMX lighting console.
TITAN PLUS range comprises 3 models, which employ different sets of LEDs tailored for distinct
applications: TITAN PLUS SOLO FULL COLOUR, TITAN PLUS SOLO RGBA and TITAN PLUS
SOLO WHITE.
TITAN PLUS SOLO FULL COLOUR: 15 x 3W Full Colour LEDs; 16 million colours; 1600 Lux at
3 m (spot lenses); linear colour temperature 2800°K ÷ 6500°K; 16 selectable types of White.
The 15 Full Colour LEDs all generate the same colour at the same time, so that the illuminated
object is not only uniformly lit, but also projects no false shadows.
TITAN PLUS SOLO RGBA: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber); 16
million colours; 4446 Lux at 3 m (spot lenses); linear colour temperature 2800°K ÷ 6500°K; 16
selectable types of White. The LEDs distribution pattern guarantees high mixing quality for
RGBA colours and a uniform projection on surfaces, no matter what colour is used.
TITAN PLUS SOLO WHITE: 54 x 1W P4 LEDs (42 x White, 12 x Amber); 5292 Lux at 3 m (spot
lenses); linear colour temperature 2800°K ÷ 6500°K; 16 selectable types of White.
TITAN PLUS SOLO WHITE is ideal in various applications where colour is not needed and white
light must have well defined features.
Full Colour LEDs Power supply on board
03.LDB030S.F10 TITAN PLUS SOLO IP20 FULLCOLOUR SPOT LENSES
03.LDB030S.F25 TITAN PLUS SOLO IP20 FULLCOLOUR MEDIUM FLOOD LENSES
03.LDB030S.F40 TITAN PLUS SOLO IP20 FULLCOLOUR WIDE FLOOD LENSES
03.LDB036C.F10 TITAN PLUS SOLO C IP65 FULLCOLOUR SPOT LENSES
03.LDB036C.F25 TITAN PLUS SOLO C IP65 FULLCOLOUR MEDIUM FLOOD LENSES
03.LDB036C.F40 TITAN PLUS SOLO C IP65 FULLCOLOUR WIDE FLOOD LENSES
Red/Green/Blue/Amber LEDs Power supply on board
03.LDB030S.T10 TITAN PLUS SOLO IP20 RGBA SPOT LENSES
03.LDB030S.T25 TITAN PLUS SOLO IP20 RGBA MEDIUM FLOOD LENSES
03.LDB030S.T40 TITAN PLUS SOLO IP20 RGBA WIDE FLOOD LENSES
03.LDB036C.T10 TITAN PLUS SOLO C IP65 RGBA SPOT LENSES
03.LDB036C.T25 TITAN PLUS SOLO C IP65 RGBA MEDIUM FLOOD LENSES
03.LDB036C.T40 TITAN PLUS SOLO C IP65 RGBA WIDE FLOOD LENSES
3 X White/Amber LEDs Power supply on board
03.LDB030S.W10 TITAN PLUS SOLO IP20 WHITE SPOT LENSES
03.LDB030S.W25 TITAN PLUS SOLO IP20 WHITE MEDIUM FLOOD LENSES
03.LDB030S.W40 TITAN PLUS SOLO IP20 WHITE WIDE FLOOD LENSES
03.LDB036C.W10 TITAN PLUS SOLO C IP65 WHITE SPOT LENSES
03.LDB036C.W25 TITAN PLUS SOLO C IP65 WHITE MEDIUM FLOOD LENSES
03.LDB036C.W40 TITAN PLUS SOLO C IP65 WHITE WIDE FLOOD LENSES
an integrated power supply and is therefore extremely easy
to set up and use.
2 integrated power supply with different protection rating are available: IP20 (Powercon + XLR
connectors) and IP65 (3 x 1.5 sq mm Main AC cable 1 meter length +
1 meter cable length).
TITAN PLUS SOLO
3

LED technology
TITAN PLUS SOLO FULL COLOUR: 15 x Full Colour LEDs; 1600 Lux / 3 m (spot lenses)
TITAN PLUS SOLO RGBA: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber;
4446 Lux / 3 m (spot lenses)
TITAN PLUS SOLO WHITE: 54 x 1W P4 LEDs (42 x White, 12 x Amber) 5292 Lux / 3 m (spot
lenses)
Variable colour temperature: 2.800°K÷6.500°K
No infrared emission; no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical units
3 lenses sets available (Spot, Medium flood, Wide flood)
Control
Via any DMX lighting console
Protection
IP20 or IP65 protection level against the penetration of solids and liquids
Construction
TITAN PLUS SOLO is made on aluminium
Power supply
Internal power supply
Connection
M12 connection system between head and power supply (
)
Powercon + XLR connectors
XLR Male / Female cable connectors
ACCESSORIES
Lenses set Spot (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.035)
Lenses set Medium flood (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.036)
Lenses set Wide flood (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.037)
Lenses set Spot (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.038)
Lenses set Medium flood (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.039)
Lenses set Wide flood (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.040)
4x2xAWG24 multipolar black outdoor cable (Cod. 0509C062)
M12 female (8 poles) cable connector (Cod. 0520P050)
M12 male (8 poles) cable connector (Cod. 0520P051)
MAIN ELECTRICAL CHARACTERISTICS:
Input Voltage Range : Vin 90 - 260 Vac
Frequency : 50 - 60 HZ
Power Consumption Range : 6 - 100 W
Power Factor ( Pf) : 0.95 electronic PFC controller
Efficiency : 90% typical
Output:
Power Output Range : 4 channels output 1,5 - 25W per channel
Output Current : 350 mA @ 100% per channel (500mA @ 100% per channel in BOOST Mode)
Output Voltage : Vout 48V
Control Input:
Control Signal : DMX 512
Dimming System :Constant Current PWM
Address Range : DMX 512 channels addressable by display
TITAN PLUS SOLO IP20 / TITAN
PLUS SOLO IP65
panel (TITAN PLUS SOLO IP20)
3 x 1.5 sq mm Main AC cable 1 meter length + 1 meter
cable length (TITAN PLUS SOLO IP65)
TITAN PLUS SOLO
4

IMPORTANT SAFETY INFORMATION
Fire prevention:
Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm
Replace any blown or damaged fuses only with those of identical value
Prevention from electric shock:
High voltage is present inside the unit.
Unplug the unit prior to performing any operation which involves touching the inside of the unit.
This equipment must be grounded, do not connect to non-grounded supplies.
Use only AC supplies 90-260V, 50-60Hz
TITAN PLUS SOLO IP20 should never be located in position exposed to rain or in areas of
extreme humidity.
A good air ventilation is essential for proper equipment work.
Safety:
The external surface of the unit may exeed 50°C; never handle the unit until at least 5 minutes
have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exeed 40°C and should not be lower than -10°C
UNIT DIMENSIONS:
The use of a thermal magnetic circuit breaker is recommended for each TITAN PLUS SOLO unit.
Unit Dimensions
(LxWxH)
250 x 256 x 206 mm
Weight
6,3 Kg
Packing Dimensions
(LxWxH)
300 x 320 x 220 mm
Weight
7,5 Kg
TITAN PLUS SOLO
5

INPUT/OUTPUT CONNECTIONS
TITAN PLUS SOLO IP20
Mains 90-260 V AC
50-60 Hz input Powerconn
Female panel connector
DMX IN/OUT
XLR 5 pins Male / Female
Panel Connectors
Fuse 3,15 AT
DMX IN/OUT
XLR 3 pins Male / Female
Panel Connectors
Panel display
Pin1
234
5
6
7
M12 LED output
Female cable connector
Pin1
2
3
4
5
67
M12 LED input
Male cable connector
LEDS
CONNECTOR PINOUT
4-GREEN -
5-BLUE +
6-BLUE -
7-AMBER - (RGBA / WHITE)
8-AMBER + (RGBA / WHITE)
1-RED +
2-RED -
3-GREEN +
LEDS
CONNECTOR
4-GREEN - (FC / RGBA / WHITE)
5-BLUE + (FC / RGBA / WHITE)
6-BLUE - (FC / RGBA / WHITE)
7-
1-RED + (FC / RGBA / WHITE)
2-RED - (FC / RGBA / WHITE)
3-GREEN + (FC / RGBA / WHITE)
TITAN PLUS SOLO
6

INPUT/OUTPUT CONNECTIONS
TITAN PLUS SOLO IP65
Mains 90-260 V AC
50-60 Hz input
3 x 1.5mm Cable
DMX IN/OUT
XRL 5 pin Female
Cable Connectors
Display panel
Pin1
234
5
6
7
M12 LED output
Female cable connector
Pin1
2
3
4
5
67
M12 LED input
Male cable connector
LEDS
CONNECTOR PINOUT
4-GREEN -
5-BLUE +
6-BLUE -
7-AMBER - (RGBA / WHITE)
8-AMBER + (RGBA / WHITE)
1-RED +
2-RED -
3-GREEN +
LEDS
CONNECTOR
4-GREEN - (FC / RGBA / WHITE)
5-BLUE + (FC / RGBA / WHITE)
6-BLUE - (FC / RGBA / WHITE)
7-
1-RED + (FC / RGBA / WHITE)
2-RED - (FC / RGBA / WHITE)
3-GREEN + (FC / RGBA / WHITE)
Fuse 3,15 AT
DMX IN/OUT
XRL 5 pin Male
Cable Connectors
2
CONTROLLER
S T A N D A R D
D M X 5 1 2
Please note that the XLR connectors installed on the TITAN PLUS IP65 have
an IP20 protection rate.
Thus, for any application where an IP65 rate is needed, the XLR connectors
must be protected within an IP65-rated container.
TITAN PLUS SOLO
7

DMX SIGNAL CONNECTION:
TITAN PLUS SOLO IP20
The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø0.5 mm.
P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN
projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to
the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
5
3
4 2
11=GND
2=DATA-
3=DATA+
CONTROLLER
S TA N D A R D
D M X 5 1 2
TITAN PLUS SOLO
8

5
3
4 2
11=GND
2=DATA-
3=DATA+
CONTROLLER
S TA N D A R D
D M X 5 1 2
DMX SIGNAL CONNECTION:
TITAN PLUS SOLO IP65
The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø 0.5 mm.
P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN
projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to
the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
Please note that the XLR connectors installed on the TITAN PLUS IP65 have
an IP20 protection rate.
Thus, for any application where an IP65 rate is needed, the XLR connectors
must be protected within an IP65-rated container.
TITAN PLUS SOLO
9

DMX ADDRESS
Projector 1 A001
Projector 2 A010 If you want to select the next projector, just add “9”
Projector 3 A019
….. A….
projector 6 A046
Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “10”
Projector 3 A021
….. A….
projector 6 A051
Selelcting the DMX address
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the
display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and
you get a faster selection.
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TITAN PLUS SOLO FULL COLOR can be used in seven different modes: 9 DMX channels mode
(default), 5 DMX channels mode (Shutter + Dimmer + RGB), WALL mode (6 DMX channels; for
use with DTS Wall mounted DMX controller 0514L007), M3CH mode (4 DMX channels; Dimmer +
RGB), RGB mode (3 channels), 1 DMX channel mode or CUSTOM DMX mode (not yet
implemented).
TITAN PLUS SOLO RGBA and TITAN PLUS SOLO WHITE can be used in seven different modes:
10 DMX channels mode (default), 6 DMX channels mode (Shutter + Dimmer + RGBA), WALL
mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007), M4CH mode (5
DMX channels; Dimmer + RGBA), RGBA mode (4 channels), 1 DMX channel mode or CUSTOM
DMX mode (not yet implemented).
If you want to use the TITAN PLUS SOLO FULL COLOR in “WALL” mode, select the “WALL”
mode from the MODE menu and set the following addresses on the mixer: (To be used only
with DTS Wall mounted DMX controller 0514L007)
Projector 1 A001
Projector 2 A009
Projector 3 A017
….. A….
projector 6 A041
If you want to use the TITAN PLUS SOLO FULL COLOR in 9 channels mode, select the 9 CH
mode from the MODE menu and set the following addresses on the mixer:
If you want to use the TITAN PLUS SOLO RGB and TITAN PLUS SOLO WHITE in 10 channels
mode, select the 10 CH mode from the MODE menu and set the following addresses on the
mixer:
TITAN PLUS SOLO
If you want to select the next projector, just add “8”
DTS Wall mounted DMX controller 0514L007 assign 8 DMX
channels per unit also if some channels are not used
10