Gcom520 SMS Programming Codes
Default Administration Password (P/W) = 123456 (Can be changed to Alpha Numerical) (See note 2 below)
Default for Operator PIN = 999999
Max tel. number size = 16 Digits (Use international format e.g. +27831231234)
Note that all SMS commands must always finish with a “;” (semi-colon)
Parameter Settings Table
PGM Parameter Admin P Code Data Default
Change Admin default Password (P/W) Old P/W, A1A, or CPWORD, New 6 character password; 123456
Change 6 digit Operator PIN Old PIN, A1P, or COPIN, New 6 digit Operator PIN; 999999
Change device name Password, D1A, or DEVNAME, Device name; (max. 20 characters)
Change device number Password, D2A, or DEVNUM, Tel. number;
Add a SMS recipient Password, ADDRECIP1, Tel. number;
or ADDRECIP2, etc. Tel. number; (max. 6)
Delete a SMS recipient Password, DELRECIP1, Tel. number;
Add a gate access number Password, F2A, or ADDNUM, Tel. number; (See note 4 below)
Delete gate access number Password, F2D, or DELNUM, Tel. number;
Enable security mode Password, F3E; or SECURITY ON; ON
Disable security mode Password, F3D; or SECURITY OFF; ON
Enable daily SMS status report Password, F4E; or STATUS ON; OFF
Disable daily SMS status report Password, F4D; or STATUS OFF; OFF
Daily SMS status report time Password, F4T, or STAT TIME, hh:mm; (24 hour format)
Request status report Password, F4S; or STATUS;
Request Configuration report Password, F4C; or CONFIG;
Enable power up report Password, F5E; or POWERUP ON; OFF
Disable power up report Password, F5D; or POWER OFF;
Power up report to recipient 1 Password, F5S; or SMSALL OFF; OFF
Power up report to ALL recipients Password, F5A; or SMSALL ON; ON
Manually set the internal clock Password, TIME;
Manually request remaining airtime Password, AIRTIME;
Reset the Gcomm to factory default Password, DEFAULT;
Set relay control to missed call Password, F7P; or RELAY MCALL; ON
Input (IP1) alarm delay Password, DELAY1,seconds; (1-999 max. seconds) 2 sec.
Input (IP2) alarm delay Password, DELAY2,seconds; (1-999 max. seconds) 2 sec.
Input (IP1) alarm message Password, ALARM1,message; (max. 50 characters)
Input (IP2) alarm message Password, ALARM2,message; (max. 50 characters)
Request software upgrade Password, SW UPDATE;
Change relay1 pulse time Password, TRIGTIME;seconds; (1-99 max. seconds) 1 sec.
Auto close override - GATE open Password, OPEN; Use relay 1
Auto close override - GATE close Password, CLOSE; Use relay 1
Operators Commands ---------------------------------------------------------------------(Can use Oper. PIN or Password)
Pulse relay 1 Oper. PIN, RELAY1 PULSE,second; (max. 99 seconds) 1 sec.
Notes
1) The 6 character password is case sensitive. All other text is not case sensitive.
2) When the customised alarm message is a command to another Gcom520 – terminate the line with a comma and a
Semi-colon e.g. 123456,RELAY1 ON,123456,PULSE;
3) See the “MY GCOM MANAGER” portal at www.gcom500.co.za for convenient device setup and management.
4) Add a gate access number, EG:
123456,ADDNUM,+27831234567; for unlimited vehicle access.
or 123456,ADDNUM,+27831234567,07:00,16:00; for limited access 7 days a week.
or 123456,ADDNUM,+27831234567,07:00,16:00,0000010,V; for limit vehicle access 1 day in a week. (Saturdays)
5) The 6 character Admin Password is case sensitive. All other text is not case sensitive.
6) For gate open wiring, use RELAY 1, miss call mode.
