Dukane ImagePro 8039B User manual

Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright April, 2003
Disclaimer
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. The manufacturer
reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to
notify any person of such revision or changes.
Trademark Recognition
All product names used in this manual are the properties of their
respective owners and are acknowledged.

LCD Projector—User Manual
— ii —
Important Safety Information
Congratulations on purchasing the LCD projector!
Important:
It is strongly recommended that you read this section carefully
before using the projector. These safety and usage instructions
will ensure that you enjoy many years safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of
hazardous situations.
The following boxes are used in this manual to alert you to important
information.
NOTE:
PROVIDES ADDITIONAL INFORMATION ON THE TOPIC AT HAND.
IMPORTANT:
PROVIDES ADDITIONAL INFORMATION THAT SHOULD NOT BE OVERLOOKED.
CAUTION:
ALERTS YOU TO SITUATIONS THAT MAY DAMAGE THE UNIT
WARNING:
ALERTS YOU TO SITUATIONS THAT MAY DAMAGE THE UNIT, CREATE A
HAZARDOUS ENVIRONMENT, OR CAUSE PERSONAL INJURY.
Throughout this manual, component parts and items in the OSD menus
are denoted in bold font as in this example:
“Push the Menu button on the remote control to open the Main menu.”

Preface
–iii –
General Safety Information
Ø Do not open the unit case. Aside from the projection lamp, there
are no user-serviceable parts in the unit. For servicing, contact
qualified service personnel.
Ø Follow all warnings and cautions in this manual and on the unit
case.
Ø The projection lamp is extremely bright by design. To avoid
damage to eyes, do not look into the lens when the lamp is on.
Ø Do not place the unit on an unstable surface, cart, or stand.
Ø Avoid using the system near water, in direct sunlight, or near a
heating device.
Ø Do not place heavy objects such as books or bags on the unit.
Power Safety
Ø Only use the supplied power adapter.
Ø Do not place anything on the power cord. Place the power cord
where it will not be in the way of foot traffic.
Ø Remove the batteries from the remote control when storing or not
in use for a prolonged period.
Replacing the Lamp
Ø Replacing the lamp can be hazardous if done incorrectly. Refer to
“Replacing the Projection Lamp” on page 27 for clear and safe
instructions for this procedure.
Ø Unplug the power cord.
Ø Allow the lamp sufficient time to cool.

LCD Projector—User Manual
— iv —
Cleaning the Projector
Ø Disconnect the power plug before cleaning. Refer to “Cleaning the
Projector” on page 30.
Ø Allow the lamp sufficient time to cool.
Regulatory Warnings
Ø Before installing and using the projector, read the regulatory
notices in the “Regulatory Compliance” section on page 40.
About this manual
This manual is intended for end users and describes how to install and
operate your LCD projector. This manual includes the following topics:
Ø Product description and features
Ø Hardware installation procedure
Ø Operation
Ø Maintenance
Ø Troubleshooting procedures
Ø Technical Specifications

Preface
–v –
Table of contents
GETTING STARTED .................................................................................... 1
PACKING CHECKLIST...................................................................................... 1
MAIN FEATURES............................................................................................. 2
PROJECTOR PARTS.......................................................................................... 3
PROJECTOR CONNECTORS .............................................................................. 4
PROJECTOR BOTTOM ...................................................................................... 5
REMOTE CONTROL PARTS .............................................................................. 6
REMOTE CONTROL HOTKEYS ......................................................................... 7
REMOTE CONTROL AND UNIT KEY PAD COMPARISON ................................... 8
SETUP AND OPERATION ........................................................................... 9
INSERTING THE REMOTE CONTROL BATTERIES .............................................. 9
REMOTE CONTROL OPERATING RANGE........................................................ 10
CONNECTING INPUT DEVICES....................................................................... 11
STARTING AND SHUTTING DOWN THE PROJECTOR........................................ 12
ADJUSTING THE PROJECTOR LEVEL.............................................................. 14
ADJUST THE ZOOM, FOCUS AND KEYSTONE................................................. 15
ON-SCREEN DISPLAY MENU SETTINGS............................................. 16
ON-SCREEN DISPLAY MENU CONTROLS ...................................................... 16
Setting the OSD Language....................................................................... 16
Main Menu ............................................................................................... 18
Setup Menu............................................................................................... 19
ColorMgr Menu ....................................................................................... 21
Language Menu........................................................................................ 23
Utility Menu ............................................................................................. 24
Status Menu.............................................................................................. 26
MAINTENANCE AND SECURITY ........................................................... 27
REPLACING THE PROJECTION LAMP ............................................................. 27
Resetting the Lamp................................................................................... 29
CLEANING THE PROJECTOR .......................................................................... 30
Cleaning the Lens..................................................................................... 30
Cleaning the Case .................................................................................... 31
USING THE KENSINGTON LOCK .................................................................... 31

LCD Projector—User Manual
— vi —
TROUBLESHOOTING................................................................................ 32
COMMON PROBLEMS AND SOLUTIONS .......................................................... 32
TIPS FOR TROUBLESHOOTING ....................................................................... 32
LED ERROR MESSAGES ............................................................................... 33
IMAGE PROBLEMS ........................................................................................ 33
LAMP PROBLEMS.......................................................................................... 34
REMOTE CONTROL PROBLEMS ..................................................................... 35
AUDIO PROBLEMS ........................................................................................ 36
HAVING THE PROJECTOR SERVICED ............................................................. 36
SPECIFICATIONS AND WARRANTY..................................................... 37
SPECIFICATIONS ........................................................................................... 37
Input/output connectors ........................................................................... 38
DIMENSIONS ................................................................................................. 39
REGULATORY COMPLIANCE................................................................ 40
FCC WARNING............................................................................................. 40
SAFETY CERTIFICATIONS.............................................................................. 40
EN 55022 WARNING.................................................................................... 40
TAIWAN BSMI ............................................................................................. 40

GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are
included:
LCD projector Remote control Two AAA batteries
Power cord RGB cable USB cable
CD-ROM (User’s manual) Quick start guide Carrying case
Contact your dealer immediately if any items are missing, appear damaged,
or if the unit does not work.

LCD Projector—User Manual
– 2 –
Main Features
• Lightweight unit, easy to pack away and transport
• Sleek easy-to-operate remote control with laser pointer and
mouse pad
• Compatible with all major video standards including NTSC, PAL,
and SECAM
• An 1200-ANSI lumens brightness rating allows for presentations
daylight or in lit rooms
• Supports resolutions up to SXGA at 16.7 million colors to deliver
crisp, clear images
• Flexible setup allows for front rear and ceiling projection
• Line-of-vision projections remain square, with advanced keystone
correction for angled projections
• Input source automatically detected
CAUTION:
AVOID USING THE PROJECTOR IN DUSTY ENVIRONMENTS.

–3 –
Projector Parts
LED Status Description
Orange Lamp ready—you can safely turn on or off the projectorLamp-ready
Flashing Lamp not ready—do not press the power button
Green Unit is powered on and working correctly
Off Unit is powered off
Power
Flashing Operational error code (refer to “LED Error
Messages” on page 33)
Image-focus contro
l
Image-zoom
control
Lamp-ready LED
OSD menu
button
Select-input source
/
left
-
curso
r
Power LED
Powe
r
AC socket
Lens
Height adjuster
button
(
both sides
)
Height adjusters
Remote control
sensor (rear)
Remote control
sensor (front)
Keystone/up-cursor
Keystone/down-
cursor
Auto-image set/
right-cursor
Connectors
(next page)
Air vents
Powe
r
POWER
MENU
KEYSTONE
SOURCE
A
UTO
READ
Y

LCD Projector—User Manual
– 4 –
Projector Connectors
Connector External device Refer to:
S-video
Video
Left audio
Audio/
video
ports
Right audio
Connect to VCR, DVD player,
or digital video camera
Page 11
Stereo mini-jack
USB Mouse
VGA/RGB-in
Connect to PC Page 11
VGA/RGB-out Connect to 2nd projector or display
RS-232 Service port for firmware upgrades
Kensington Lock Secure to permanent object with a
Kensington lock system
Page 31
S-video
VGA/RGB-in VGA/RGB-out
USB
Mouse
Video
Audio I/P
L
R
PC
Audio-in
RS-232
Kensington
Lock Slot
Audio/video Ports

–5 –
NOTE:
IF YOUR VIDEO EQUIPMENT HAS BOTH S-VIDEO AND RCA JACKS, CONNECT TO
THE S-VIDEO CONNECTOR. S-VIDEO PROVIDES A BETTER QUALITY SIGNAL.
Projector Bottom
Item Description Page ref.
Height adjusters Adjust level of the front of the
projector
Page 14
Projection lamp cover Remove when changing lamp Page 27
Ceiling support holes Contact your dealer for information on mounting
the projector on a ceiling.
Projector lamp cover
Ceiling supports
Height adjusters

LCD Projector—User Manual
– 6 –
Remote Control Parts
Power
Laser
Keystone Volume
L
LL
LR
RR
R
Menu Status Mute
Auto Blank Zoom
Source Freeze Zoom
WARNING:
THE LIGHT FROM A LASER IS DAMAGING TO THE EYES: NEVER POINT THE
REMOTE CONTROL LASER INTO ANYONE’S EYES.
Laser IR transmitter
Power LED
Power button
Right-mouse button
Keystone button
Laser button
Mouse pa
d
Volume button
Left-mouse button
Left/right-cursor buttons
Volume mute button
Status button
Menu button
Auto-image set button
Select-input source
button
Freeze-screen button
Zoom-in button
Blank display/audio
mute button
Zoom-out button
Down-cursor button
Up-cursor button
Menu Enter button

–7 –
Remote Control Hotkeys
There are a number of hotkeys on the remote, which let you quickly adjust
projector settings.
Item Description
Keystone Use this button to correct distortion (trapezoid
effect) of the projected image.
Volume Use this button to adjust the volume.
Menu Use this button to open the On-Screen Display
(OSD).
Status Use this button to check configuration settings.
Auto Use this button to optimize image size, position,
and resolution.
Blank Press to blank the screen; press again to show the
screen.
Zoom+/Zoom- Use these buttons to zoom in or out on the screen.
Press the cursor buttons to pan the zoomed
image.
Source Use this button to select the input source when
more than one device is connected.
Freeze Use this button to freeze the on-screen picture.
Press again to resume motion.

LCD Projector—User Manual
– 8 –
Remote Control and Unit Key Pad Comparison
You can use the remote control or the keys on the projector to operate the
projector and navigate the On-Screen Display (OSD).
The following illustration shows the remote control buttons and their
corresponding buttons (color matched here for identification) on the
projector:
Power
Laser
Keystone Volume
L
LL
LR
RR
R
Menu Status Mute
Auto Blank Zoom
Source Freeze Zoom
READY
READYREADY
READY POWER POWERPOWER
POWER
SOURCE
SOURCESOURCE
SOURCE AUTO
AUTOAUTO
AUTO
POWER
POWERPOWER
POWER
MENU
MENUMENU
MENU
KEYSTONE
KEYSTONEKEYSTONE
KEYSTONE
IMPORTANT:
THE BUTTONS AND KEYS ON THE PROJECTOR HAVE THE SAME FUNCTIONS AS
THE CORRESPONDING BUTTONS ON THE REMOTE CONTROL AS SHOWN ABOVE.
THIS USER’S MANUAL DESCRIBES THE FUNCTIONS BASED ON THE REMOTE
CONTROL.

SETUP AND OPERATION
Inserting the Remote Control Batteries
1. Remove the battery
compartment cover by
sliding the cover in the
direction of the arrow.
2. Insert two AAA batteries
(supplied) taking note of the
battery-polarity markings
inside the compartment.
3. Replace the cover.
NOTE:
DO NOT MIX BATTERY TYPES.
DISPOSE OF USED BATTERIES ACCORDING TO LOCAL ORDINANCE REGULATIONS.

LCD Projector—User Manual
– 10 –
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is
not necessary to point the remote directly at the projector. As long as you
are not holding the remote perpendicular to the sides, the remote will
function well within a radius of about 10 meters (33 feet) and 30 degrees
above or below the projector level. If the projector does not respond to the
remote control, move a little closer. Refer to the illustrations below:
NOTES:
AVOID USING THE PROJECTOR WITH BRIGHT FLUORESCENT LIGHTING TURNED ON. CERTAIN
HIGH-FREQUENCY FLUORESCENT LIGHTS CAN DISRUPT REMOTE CONTROL OPERATION.
BE SURE NOTHING OBSTRUCTS THE PATH BETWEEN THE REMOTE CONTROL AND THE
PROJECTOR. IF THE PATH BETWEEN REMOTE AND PROJECTOR IS OBSTRUCTED, YOU CAN
BOUNCE THE REMOTE SIGNAL OFF CERTAIN REFLECTIVE SURFACES SUCH AS PROJECTOR
SCREENS.
10M (33 ft.)
60 degree
s

–11 –
Connecting Input Devices
You can connect more than one input device to the projector at the same
time. The procedure below shows examples of typical input devices.
Connect the USB cable to the
projector and the PC.
Connect a cable (not supplied)
to the projector’s VGA/RGB-
in connector and the PC’s
video-out connector. Tighten
the securing screws on both
connections.
Connect a video device (VCR,
DVD or video camera) to the
A/V ports. If the device has
both S-video and composite
video connectors (RCA jacks),
use S-video for better quality.
Connect a second projector or
display to the RGB-out
connector.
VCR/DVD or
video camera
2n
d
projector
or display

LCD Projector—User Manual
– 12 –
Starting and Shutting down the Projector
1. Connect the power cord to
the projector. Connect the
other end to a wall outlet.
The power LED and Lamp-
ready LED turn on.
2. Turn on the connected devices.
3. Ensure the Lamp-ready LED
is on a steady (not flashing)
orange and then press the
Power button to turn on the
projector.
The projector splash screen
displays and connected
devices are detected.

–13 –
4. Press the Source button and
then use the cursor
button to move up and down
in the list of input devices.
Press the button to
change the input device.
(DVD and HDTV are
supported through the RGB-
in connector and an optional
RGB cable.)
5. To finish your presentation, turn off the projector.
IMPORTANT:
IF YOU HAVE CONNECTED THE USB CABLE TO A PC, THE PROJECTOR IS
DETECTED BY THE PC. YOU MAY BE PROMPTED TO INSTALL DRIVERS FOR THE
REMOTE CONROL MOUSE PAD; FOLLOW THE ONSCREEN INSTRUCTIONS FOR
YOUR PC’S OPERATING SYSTEM.

LCD Projector—User Manual
– 14 –
Adjusting the Projector Level
1. To raise the level of the
projector, lift the projector
[A] and press both Level
adjuster buttons [B].
The Level adjusters drop
down [C].
2. To make minor adjustments,
rotate the adjusters.
3. To lower the level of the
projector, press both Level
adjuster buttons [A] and
push down [B].