Dura-Max Metal Garden Shed Manual

OWNER’S MANUAL /
Instructions for Assembly
Metal Garden Shed
Size 6’ x 4’ with “Extension Kits”
Customer
Service Hotline
[phone]
www.uspolymersinc.com
• Tall Walk in Shed
• Quick & Easy Assembly
• Ridge Reinforced Walls
• Wide Double Doors
• Available in Various Sizes
Call us for any missing or damaged parts.
Do not return to the store.
Requires twopeopleandtakes2-3hoursfor Installation.
PART 1
ASSEMBLING SHED WITH EXTENSION KIT
PART 2
ADDING EXTENSION KIT TO EXISTING SHED
Note: For shed with extension use this manual only.
ALL PURPOSE METAL STORAGE SHEDS
A Product of
US POLYMERS INC
USP
TM

Duramax Storage Shed
Limited Fifteen Year Warranty
U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or
workmanship for a period of fifteen years from the date of purchase.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original
purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring,
labor, installation or any other costs related thereto.
This warranty only covers failures due to defects in material or workmanship which occurs during normal
use and does not extend to color change arising due to normal weathering or to damage resulting from
misuse or neglect, commercial use, failure to follow assembly instructions and the owner’s manual (including
proper anchoring of the shed), painting, forces of nature and other causes which is beyond our control.
Claims under this warranty must be made within the warranty period by calling 1-800-483-4674 or mail in
a dated sales slip and clear photograph of the part to:
U.S. Polymers, Inc.
6915 Slauson Avenue
Commerce, CA 90040
We reserve the right to discontinue or change components. If a component has been discontinued or is
not available,
U.S. Polymers, Inc. reserves the right to substitute a component of equal quality as may be compatible.
Limits and Exclusions
There are no express warranties except as listed above. The warrantor shall not be liable for incidental or
consequential damages resulting from the use of this product, or arising out of any breach of this warranty.
All express warranties are limited to the warranty period set forth above . Some states do not allow the
exclusion or limitation on how long an implied warranty lasts, so the above limitations may not apply to
you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to
state or country to country.

Note: Check all parts prior to installation.
CODE DESCRIPTION QTY
BLC BASE BAR BACK LEFT 1
BRC BASE BAR BACK RIGHT 1
BSC BASE BAR SIDE LEFT & RIGHT 2
BBFC BASE BAR FRONT LEFT & RIGHT 2
ECC ENTRANCE TAPER CHANNEL 1
DCLC DOOR COLUMN PROFILE LEFT 1
DCRC DOOR COLUMN PROFILE RIGHT 1
ABLC TOP ANGLE BACK LEFT 1
ABRC TOP ANGLE BACK RIGHT 1
ASC TOP ANGLE SIDE LEFT & RIGHT 2
SCC SLIDING CHANNEL COVER 1
SSB SLIDING CHANNEL SUPPORT 1
SLC SLIDING CHANNEL LEFT 1
SRC SLIDING CHANNEL RIGHT 1
RSC ROOF SUPPORT LEFT & RIGHT 2
RF1C ROOF FLASHING (FRONT RIGHT / BACK LEFT) 2
RF2C ROOF FLASHING (FRONT LEFT / BACK RIGHT) 2
RFSA ROOF FLASHING SIDE LEFT & RIGHT 2
RFCC ROOF FLASHING CENTER 1
TSLC DOOR PANEL STRIP TOP LEFT 1
TSRC DOOR PANEL STRIP TOP RIGHT 1
BDSC DOOR PANEL STRIP BOTTOM LEFT/RIGHT 2
DSSC DOOR PANEL STRIP SIDE LEFT & RIGHT 2
DSCC DOOR PANEL STRIP CROSS 4
WCFC WALL PANEL CORNER FRONT LEFT & RIGHT 2
WCBC WALL PANEL CORNER BACK LEFT & RIGHT 2
WSC WALL PANEL SIDE 3
WFLC WALL PANEL FRONT LEFT 1
WFRC WALL PANEL FRONT RIGHT 1
GPLC GABLE PANELFRONT LEFT/BACK RIGHT 2
GPRC GABLE PANEL FRONT RIGHT/BACK LEFT 2
GPS GABLE PANEL SUPPORT 2
RP1C ROOF PANEL FRONT LEFT / BACK RIGHT 2
RP2C ROOF PANEL FRONT RIGHT/BACK LEFT 2
DPLC DOOR PANELLEFT 1
DPRC DOOR PANEL RIGHT 1
Parts List
Hand Gloves
Cordless Drill - Philips Head
Screw driver - Philips Head
Carpenters Square
Eye Protector
Tools You Will Need
ACCESSORIES
CODE DESCRIPTION QTY
BS BOTTOM SLIDER 4
DH DOOR HANDLE 2
FC FLASHING END CAP 2
TC TOP CORNER 4
TS TOP SLIDER 4
VC VENTILATION COVER 4
PW PLASTIC WASHER 134
PC PLASTIC SCREW COVER 86
WST WEATHER STRIPPING TAPE 2.00 mtr
S1 DIA. 4.2 x 10mm. (5/32” x 3/8”)
SHEET METAL SCREW 160
S2 DIA. 4.2 x 16mm. (5/32” x 5/8”)
SHEET METAL SCREW 22
S3 M4 x 16mm. (5/32” x 5/8”)
MACHINE SCREW W/ NUT 53
8’ Step Ladder
Adjustable pliers
Level - 3ft.
Tape Measure
BOTTOM SLIDER
(BS)
VENTILATION COVER
(VC)
TOP CORNERS
(TC) TOP SLIDER
(TS)
PLASTIC WASHER
(PW) PLASTIC SCREW COVER
(PC)
SHEET METAL SCREW
(S1),(S2) MACHINE SCREW WITH
NUT (S3)
FLASHING END CAP
(FC)
DOOR HANDLE
(DH)
ENTRANCE TAPER
CHANNEL (ECC)
SLIDING CHANNEL COVER
(SCC)
DOOR COLUMN PROFILE
LEFT (DCLC)
DOOR PANEL STRIP SIDE
AND CROSS
(DSSC, DSCC)
SLIDING CHANNEL
(SLC, SRC) SLIDING CHANNEL
SUPPORT (SSB)
ROOF SUPPORT
(RSC)
ROOF FLASHING
(RF1C, RF2C) ROOF FLASHING CENTER
(RFCC)
DOOR PANEL STRIP
TOP AND BOTTOM
(TSLC, TSRC, BDSC)
TOP ANGLE BACK
(ABLC, ABRC)
BASE BAR
(BBFC)
BASE BAR
(BLC, BRC, BSC)
TOP ANGLE SIDE
(ASC)
DOOR COLUMN PROFILE
RIGHT (DCRC)
ACCESSORIES
PROFILES
WEATHER STIPPING TAPE
(WST)
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
GABLE PANEL SUPPORT
(GPS)

Exploded View
DPLC
DPRC
SCC
DCLC
WFLC
DCRC
WFRC
BSC
BBFC
ECC
BRC
WCBC
WCFC
ASC
SLC
SRC
ABRC
GPLC
GPRC
RP1C
RP2C
RF1C
RF2C
RFCC
RFSA
WSC
BLC
ABLC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
RF1C
RF2C RP1C
RP2C
RFSA
RSC
GPRC
GPLC
ASC
WSC WSC
WCFC
WCBC
BBFC
SSB
BSC
GPS

IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Note: Check all parts prior to installation.
CODE DESCRIPTION QTY
EBS1 BASE BAR SIDE EXTENSION LEFT 1
EBS2 BASE BAR SIDE EXTENSION RIGHT 1
EAS1 TOP ANGLE SIDE EXTENSION LEFT 1
EAS2 TOP ANGLE SIDE EXTENSION RIGHT 1
ERS1 ROOF SUPPORT EXTENSION LEFT 1
ERS2 ROOF SUPPORT EXTENSION RIGHT 1
ERFS ROOF FLASHING SIDE EXTENSION LEFT/RIGHT 2
ERFC ROOF FLASHING CENTER EXTENSION 1
WSC WALL PANEL SIDE 2
RELC ROOF PANEL 1
RERC ROOF PANEL 1
One Extension Parts List
ACCESSORIES
CODE DESCRIPTION QTY
PW PLASTIC WASHER 38
PC PLASTIC SCREW COVER 15
S1 DIA. 4.2 x 10mm. (5/32” x 3/8”)
SHEET METAL SCREW 40
S2 DIA. 4.2 x 16mm. (5/32” x 5/8”)
SHEET METAL SCREW 6
S3 M4 x 10mm. (5/32” x 3/8”)
MACHINE SCREW WITH NUT 6
WST WEATHER STRIPPING TAPE 1.5MTR
ROOF SUPPORT
(ERS1, ERS2)
ROOF FLASHING CENTER
(ERFC)
PROFILES
TOP ANGLE SIDE
(EAS1, EAS2)
ROOF FLASHING SIDE
(ERFS)
BASE BAR
(EBS1, EBS2)
PLASTIC WASHER
(PW) PLASTIC SCREW COVER
(PC)
SHEET METAL SCREW
(S2) MACHINE SCREW WITH
NUT (S3)
ACCESSORIES
WEATHER STRIPPING
TAPE
(WST)

WSC
EBS2
EBS1
WSC
EAS1
EAS2
RELC
ERFS
ERFC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Exploded View with One Extension
ERFS
RERC
ERS1
ERS2

A. Foundation & Base Frame
1. Use pressure treated wood studs 2” x 4”
(50mm x 88.9mm) to create a platform frame that
has an outside dimension of 47” x 78”
(1193.8mm x 1981.2mm).
DuraMax must be installed on a level wooden platform
or a level concrete foundation.
2. Using exterior grade CDX 3/4” (19mm) plywood,
cut and fit together the sheets to form solid foundation
as shown. Foundation must be square and level.
Note: It is important that these instructions
are followed step by step.
178” (1981.2mm)
47” (1993.8mm)
(1) Base bar back left (BLC)
(1) Base bar back right (BRC)
(2) Base bar side (BSC)
(2) Base bar front (BBFC)
(1) Entrance Taper channel (ECC)
(12) Sheet metal screw (S1)
(18) Sheet metal screw (S2)
Parts needed:
The following are the list of lumber and sizes
you will need.
Wooden Platform (Not Included)
Pressure Treated - Wood Studs:
3ea 2” x 4” x 71” (50mm x 88.9mm x 1803.4mm)
2ea 2” x 4” x 47” (50mm x 88.9mm x 1193.8mm)
Exterior Grade (CDX) - 3/4” (19mm) plywood
1ea 3/4” x 47” x 78” (19mm x 1193.8mm x 1981.2mm)
L-Brackets: 4ea
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Wooden platform is extra
and is not included.
Don’t install under
windy conditions.
Note
The following are a list of lumber and sizes
you will need.
Wooden Platform (each Extension) (Not Included)
Pressure Treated - Wood Studs:
2ea 2” x 4” x 71” (50mm x 88.9mm x 1803.4 mm)
2ea 2” x 4” x 24” (50mm x 88.9mm x 609.6 mm)
Exterior Grade (CDX) - 3/4” (19mm) plywood
1ea 3/4” x 24” x 78” (19mm x 609.6mm x 1981.2mm)
L-Brackets: 4ea
(1) Base bar side extension left (EBS1)
(1) Base bar side extension right (EBS2)
(8) Sheet metal screw (S1)
(6) Sheet metal screw (S2)
Parts needed for each Extension:
1a. Use pressure treated wood studs 2” x 4”
(50mm x 88.9mm) to create a platform frame that
has an outside dimension of 24” x 78”
(609.6mm x 1981.2mm) for each extension.
OR 1b. Use pressure treated wood studs 2”x 4”
(50mm x 88.9mm) to create a platform frame that
has an outside dimension of 71”x 78”
(1803.4mm x 1981.2mm)
for shed one extension.
PART 1: Assembling Shed With Extension Kit
Lay 50 x 88.9mm Flat
Note
24” (609.6mm)
47” (1193.8mm)
L- BRACKET
78” (1981.2mm)
L- BRACKET
18 1/4” (463.55mm)
L- BRACKET L- BRACKET
L- BRACKET L- BRACKET
71” (1803.4mm)
17” (431.8mm) 24” (609.6mm)
18 1/4” (463.55mm)

5. Assemble the base bar side (BSC) & extension
(EBS2) with (S1) screws.
Add one (EBS2) for each extension.
EBS2
S1
BSC
BSC EBS2
4. Assemble the base bar side (BSC) & extension
(EBS1) with (S1) screws.
Add one (EBS1) for each extension.
S1
EBS1
BSC
EBS1
BSC
EBS1
BSC
3. Assemble base bar back left (BLC) and base
bar back right (BRC) with four (S1) screws.
See fig. 1 & 2.
2
Fig.1 Fig. 2
BLC
BRC
S1
BLC
BRC
Take care of sharp edges.
Note
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
1 & 2
Fig.1 Fig. 2
1 & 2
Fig.1 Fig. 2
Step 1 Step 2
Step 1 Step 2
Step 1 Step 2
EBS2
BSC 1&2

6. Place the base bar back assembly (BLC) &
(BRC) on top of the foundation. Use (S2) screws
to fix the assembly to foundation.
3
S2 BLC
BRC
Front Right
Left Back
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.1
Fig.2
Step 1
Step 2
BLC
BRC
BSC
BSC
EBS1 BLC
BRC
EBS2
S1
S1
EBS1
EBS2
7. Place the base bar left side assembly (BSC) &
(EBS1)on left side. Insert the edge of (EBS1) into
the back base bar (BLC) and secure with (S1)
screws. See fig. 1.
Place the base bar right side assembly (BSC) &
(EBS2) on right side. Insert the edge of (EBS2) into
the back base bar (BRC) and secure with (S1)
screws. See fig. 2.
BSC
BSC
EBS1
EBS2
8. Using a carpenter square, line up the corners
secure base bar side assembly to the foundation
with (S2) screws.
S2
Fig.1 Fig. 2
1
Step 1 Step 2
Fig.1
1
1
2
2

4
BBFC
BBFC
BBFC
BSC
BBFC
BSC
Fig.1 Fig.2
S1
BBFC
BBFC
S2
S2
Fig.1 Fig.2
ECC
BBFC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
9. Place the base bar (BBFC) on top of (BSC) on
both sides. Secure with (S1) screw to (BSC) on
both corners. See fig. 1 & 2.
BBFC
BBFC
10. Using the carpenter square, line up the corners.
Secure the base (BBFC) to the foundation with (S2)
screws.
11. Place the entrance taper channel (ECC) on
top of the (BBFC). Secure with (S2) screws to the
foundation. See fig. 1 & 2.
ECC
1&2
Step 1 Step 2
Fig.1
1
1
1&2
Step 1 Step 2
1&2
1&2

5
12. Measure in all direction as shown in figure.
Make the base bar assembly in a perfect square.
Parts Needed:
(1) Wall panel front right (WFRC)
(1) Wall panel front left (WFLC)
(2) Wall panel corner front (WCFC)
(2) Wall panel corner back (WCBC)
(3) Wall panel side (WS)
(1) Sliding channel right (SRC)
(1) Sliding channel left (SLC)
B. Walls & Columns
12a. (Concrete foundation)Using a carpenter’s
square, line up corners. Align Base bars, mark the
concrete at the holes in the base and drill concrete
with 1/4” (dia. 6mm) concrete bit to accept anchor
bolts to a 1 3/4” (44mm) depth. Replace base and
secure with 1/4” x 1 3/8” (M6 x 35mm) anchor bolts
(not provided).
Concrete foundation
(2) Top angle side (ASC)
(1) Sliding channel support (SSC)
(1) Sliding channel cover (SCC)
(4) Top slider (TS)
(1) Door column profile left (DCLC)
(1) Door column profile right (DCRC)
(1) Top angle back left (ABLC)
(1) Top angle back right (ABRC)
(54) Plastic washer (PW)
(64) Sheet metal screw (S1)
(8) Machine screw (S3)
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
BBFC
BBFC
ECC
BSC
BSC
BRC
BLC
(
1830m
m)
(
1560mm
)
EBS1
EBS2
(
1830m
m)
(
1560mm
)
Parts Needed for each extension:
(2) Wall panel (WSC)
(1) Top angle side extension left (EAS1)
(1) Top angle side extension right (EAS2)
(15) Plastic washer (PW)
(16) Sheet metal screw (S1)
(2) Machine screw (S3)
All panels are clearly marked
and care should be taken to
use the correct one.
Note
1. Place the wall panel (WFRC) on the base bar
(BBFC). Front right side of the shed line up the holes
with base bar. Secure with (S1) screws with washers
from outside.
PW WFRC
BBFC
WFRC
Front
1
Fig.1
S1

6
4. Place the sliding channel right (SRC) on top of
the wall panel (WFRC) from inside. See the position
in fig. 1. Line up the holes with wall panel. Use (S1)
screw with washers to fix. See fig. 2.
Fig.1 Fig.2
PW
SRC
S1
WCFC
SRC
WCFC
WFRC WCFC
SRC
WCFC
WFRC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
2. Place the wall panel corner front (WCFC) on the
base bar (BSC). Line up the holes with base bar and
use (S1) screws with washers to Secure.
Make sure the overlapping
position is as shown in fig.1.
Note
Fig.1 Fig.2
WFRC
S1
WCFC BBFC BSC
WFRC WCFC
BSC
1
2
3. Use (S3) bolt and nut with washer to join together
the wall panels.
1&2
Fig.1
1
PW
S3
PW

7
5. Insert the 2 pieces of (TS) Top slider into the
sliding channel. See blowup.
Make sure the position of the
projection on (TS) towards
inside.
Note
6. Place the wall panel (WFLC) on the base bar
(BBFC). Front left side of the shed. Line up to holes
with base bar. Secure with (S1) screws with washers
from outside.
7. Place the wall panel corner front (WCFC) on the
base bar (BSC). Line up the holes with base bar
and use (S1) screws with washers to secure.
Make sure the overlapping
position is as shown in fig.1
Note
Fig.1 Fig.2
PW
WFLC
PW
BSC BBFC
WCFC
WFLC
SRC
WFRC
WFLC
Front
BSC
WCFC WFLC
2
1
BBFC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
1
1
Fig.1S1
S1
Fig.1
TS SRC
TS
Front

8
8. Use (S3) bolt and nut with washer to join together
the wall panels.
9. Place the sliding channel left (SLC) on top of the
wall panel (WFLC) from inside. See the position in
fig1. Line up the holes with wall panel use (S1) screw
with washers to fix. See fig. 2
10. Insert the 2 pieces of (TS) Top slider into the
sliding channel. See blowup.
Make sure the position of the
projection on top slider towards
inside.
Note
Fig.1 Fig.2
S3
SLC
WFLC WFLC
TS
TS
SLC
WCFC WFLC
WFLC
SLC
SLC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Front
PW
1&2
1
Fig.1
1
Fig.1
S1
PW

9
11. Place the sliding channel support (SSB) on the
sliding channel (SLC) & (SRC). See fig.1. Align the
holes with sliding channels and secure with (S1)
screws. See fig. 2.
12. Place the wall panel corner back (WCBC) on the
base bar (EBS1). Line up the holes with base bar
and use (S1) screws with washers to secure.
Fig.1 Fig.2
S1
SLC
SRC
SLC
SRC
PW
WCBC
EBS1
SSB
WCBC
BSB
Back
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
1 & 2
13. Place the wall panel (WSC) on the base bar (BLC).
Line up the holes with base bar. Secure with (S1) screw
with washers Use (S3) bolt and nut with washer to
join together in the middle of the wall panel.
See fig. 2. Make sure the overlapping
position is same as
shown in fig.1.
Note
Fig.1 Fig.2
S3
WCBC
BLC
WSC WCBC
WSC
Fig.3
1
2
3
SRC
SLC
SSB SSB
PW
1
Fig.1 S1
S1
PW

Fig.1 Fig.2
ABLC ABLC EAS1
WCBC
WCBC
EAS1
10
14. Place the top angle back left (ABLC) on top of
the wall panel (WSC) from inside. See the position
in fig.1. Line up holes with wall panel. Use (S1)
screws with washers to fix. See fig. 2
15. Place the top angle side (ASC) on top of the
wall panels (WCFC). Line up the holes and secure
with (S1) screws with washers. See fig.
Top angle (ASC) must
slide in between the
sliding channel (SLC)
and wall panel (WCFC).
Note
Fig.1 Fig.2
S1
ABLC
WCBC
ABLC
WSC
ABLC
ASC
WCFC
S1
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
16. Place the top angle side (EAS1) on top of the
wall panels (WCBC) and top angle (ABLC). Line up
the holes and secure with (S1) screws with washers.
See fig.1 & 2.
Add one (EAS1) for each extension.
Top angle (EAS1) must
sit on top angle (ABLC).
Note
ABLC
WCBC
S1
ASC
SLC WCFC
SLC
EAS1
1 & 2
1
Fig.1
1 & 2
PW

18. Place the wall panel (WSC) on top of the base bar
(BSC) and over lap with corner panels (WCBC) &
(WCFC). Secure the wall panel to top angle and base
bar with (S1) screws with washers.
Use (S3) bolt & nut with washers to join together the
middle of the wall panel. See fig. 3.
Add one (WSC) for each extension.
11
17. Use (S1) screws to join together the top angle
(ASC) & (EAS1) from outside. See fig.
WCFC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
ASC
EAS1
S1
ASC
EAS1
Make sure the overlapping
position of panels is as
shown in fig. 1 & 2
Note
WSC
1
2
3
Fig.3
Fig.1 Fig.2
PW
WCBC
WSC
S3
3
WCBC
S1
EAS1
WSC
ASC WCFC
1
Fig.1
PW
PW
S1

12
21. Place the top angle back right (ABRC) on top
of the wall panel (WSC) from inside. See the position
in fig.1. Line up the holes with wall panel use (S1)
screws with washers to secure. See fig.
Fig.1
Fig.1 Fig.2
S1
WSC
WCBC
S1
ABRC
ABRC
WSC
WCBC
BSC
WCBC
WSC
ABRC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
19. Place the wall panel corner back (WCBC) on
the base bar (EBS2). Line up the holes with base
bar and use (S1) screws with washers to secure.
EBS2
WCBC
Back
20. Place the wall panel (WSC) on the base bar
(BRC). Line up the holes with base bar and use (S1)
screws with washers to secure.
Use (S3) bolt & nut with washers to join together the
middle of the wall panel. See fig. 2.
Make sure the overlapping
position of panels is as shown in
fig. 1
Note
BRC
BLC
Fig.2
PW
WSC
1
2
1 & 2
1
Fig.1
PW
S1
PW

13
22.Join top angle back left & right (ABLC) & (ABRC)
together with (S1) screws. See blowup.
23. Place the top angle side (ASC) on top of the wall
panels (WCFC). Line up the holes with panels and
secure with (S1) screws with washers.
S1
ABRC
ABLC
ABRC
ABLC
ASC
WCBC
WCFC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Top angle must slide in between
the sliding channel (SRC) and
the wall panel (WCFC). See fig.
Note
ASC
SRC
WCFC
24. Place the top angle side (EAS2) on top of the wall
panels (WCBC). Line up the holes with panels and
secure with (S1) screws with washers.
Add one (EAS2) for each extension.
Top angle (EAS2) must sit
on top angle (ABRC). See fig.
Note
EAS2 ABRC
Fig.1 Fig.2
EAS2 ABRC
WCBC
EAS2 ABRC
WCBC
WCBC
1 & 2
1
Fig.1
1
Fig.1

14
25. Join the top angle side (ASC) & (EAS2) together
with (S1) screws from out side.
WSC
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
EAS2
ASC
EAS2
S1
ASC
WCBC
WCFC
26.Place the wall panel (WSC) on the base bar
and overlap with corner panel. Secure with (S1)
screws with washers to base bar & top angle. Use
(S3) bolt and nut with washer to join together in
middle of the wall panel. See fig. 3.
Add one (WSC) for each extension.
Make sure the overlapping
position. See fig.1 & 2.
Note
WCFC
WSC
WSC
WCBC
S3
Fig.3
Fig.1 Fig.2
S1
S1
1
2
3
3
1
Fig.1
PW
PW
PW