Durite ADAS User manual

Call 01255 555200
Email [e-mail]
Visit www.durite.co.uk
0-870-17- ADAS 1080p FHD Dash Cam
Durite’s ADAS 1080p FHD Resolution dash camera. Features include 2.0MP high resolution camera, GPS aerial monitors both
speed and location. 8-128GB TF card storage. G Sensor. Motion Detection. Parking Guard. CE Approved.
ADAS Information
LDW: Lane departure warning systems alert you if you’re drifting out of your lane using visual and audible alerts.
FCW: Forward collision warning system monitors a vehicle's speed, the speed of the vehicle in front of it, and the distance
between the vehicles. If vehicles get too close due to the speed of the rear vehicle, the FCW system will warn that driver of an
impending crash using visual and audible alerts.
TECHNICAL SPECIFICATIONS
THE TRUSTED QUALITY BRAND FOR PROFESSIONALS

WARNINGS
Before using this unit please read these instructions carefully.
Take special care to follow the warnings indicated on the unit itself as well as the safety sug-
gestions listed below.
Keep these instructions for future reference.
* Please ensure you are familiar and comply with local traffic and driving regulations.
*Power Source - The Mini DVR should be connected to a 12-24 volt dc power supply only.
*Water and Moisture - Do not use the Mini DVR where it may be subject to water ingress or
excessive moisture. Do not use outside the vehicle unprotected.
*Heat - Do not install the Mini DVR near a direct heat sources.
*Ventilation - The Mini DVR should be situated to allow free circulation of air.
*Foreign Material - Care should be taken so that objects do not fall onto or into, and that liq-
uids are not spilled on the Mini DVR.
*Mounting Surface - The Mini DVR should be mounted to a strong secure surface.
*Replacement Parts - Use only manufacturers replacement specified parts. Unauthorised sub-
stitutions may result in fire risk, electric shock or other hazards and will void the warranty
* Service - The user should not attempt to service this units beyond that described in the oper-
ating instructions.There are no user-serviceable parts within the unit.
* Screen Protective Film - Remove the LCD screen protective plastic cover before use.
*ADAS - Please calibrate before use. If you move the camera you must calibrate each time.
Product may need calibration periodically. ADAS is not as effective in adverse weather con-
ditions. ADAS is only a supportive aid and cannot be soley relied upon. Please operate with
caution.
*SD Cards - Please format the card before first use. To ensure a good state of health please
format the SD card every 4 weeks. Please ensure all sensitive data is backed up.

Structure

Installation and Operation
1. Insert a memory card: Please insert memory card on the device memory card correctly in
accordance with the direction of the gap prompt, press the card until a click is heard, insert
into place.
A CLASS 10TF Card is required. Please refer to DuriteTF/SD Cards p/n. 0-775-28 (128GB)
Note: You need to format the card if you use it for the rst time.
2. Remove the memory card: press the memory card and it will pop out
Note: Do not remove or insert a memory card while the camera is on in order to avoid damag-
ing the memory card.
3. Install centre in front of the windshield inside the vehicle. Firstly, x the device on the suc-
tion cup holder, then put the suction cup at, and place on the windshield. Then press the clip,
with the xed frame mounted centre in front of the rearview mirror windshield, to determine
the equipment locked in place.
4. Connect the power supply
Connect one end of the car charger + to the USB port of the device and the other end to the
cigarette lighter port inside the car. Also, connect the GPS aerial.
Note: Please use the factory standard original charger.
Note:This device is designed to follow the long driving time of the car. Built-in battery is
designed to save the le and park guard only. Therefore, the working time of the battery is lim-
ited. Please connect car power supply in daily use.

5.The host wiring method as shown below:

1.Devices connected to computers:
Connected to computer via USB.There are three modes:
Mass Storage: can read and write a variety of data in the memory card, including the locked
video les.
PC camera: can be used as a PC camera, real-time network video chat.
Recording mode:The device can be powered by USB data cable.
2.Motion detection:
When the object moves in front of the lens, it will automatically start recording, the recording
time is set by the device itself, usually set to 30 seconds.
3. Gravity sensor:
The device will integrate the gravity sensor, and when the device senses a vibration collision,
it will lock the video currently being recorded.
4. Parking Guard:
In the power off state, when the device senses a vibration collision, the device will automati-
cally start and automatically record, the recording time is set by the device itself, usually set to
30 seconds. After the video is nished, the device will automatically shut down and the current
video le will be locked.
Further notes
1) In order to protect the video les in case of emergency, the locked video les will not be
overwritten by other les.
2) When memory card is full with locked les, there will be an error prompt.
3) You can not delete the locked le, if you need, you can use the following methods:
A. First unlock and then delete
B. Format the memory card to clear these les
C. Connect to computer to delete these les
1. Once the vehicle has started, the device will automatically boot up. After the vehicle has
turned off, the device will shut down automatically after a certain period of time.The automat-
ic shutdown time can be set by the "Automatic shutdown" option in the system menu.
2. Only in the non-Recording video, you can press the key to call up the system menu, Press
OK button to start / pause the Recording video.
3.The rst time you use, please set the date and time, when you restore the factory settings,
you will need to re-set the date and time.
Product Use
Product Feautres

ADAS Setup
ADAS will auto calibrate but there are steps to ne tune. Ideally setup should take place on a
road with markings to be accurate. Please be aware of your surroundings.
Install and fix the dash camera on the car windshield. It is best installed in the middle position.
Enter the MENU. Select ADAS Calibration to adjust the Middle, Horizon, Left, Bonnet and Right
guidelines.
Press “Ok” button to enter --”Up” or “Down“ to adjust the red line position.
Adjust to the centre of the screen as shown below. Press OK.
Adjust the middle red line to horizon or view directly ahead. As shown below. Press OK.

Next setup the left side. Move the red line in line with the road marking as shown below. Press
OK. Repeat this step for the right side after setting the vehicle bonnet level below:
Adjust the red line to line up with the vehicle bonnet as shown below. Press OK.
Repeat the step above to set the right side. Press OK.
The ADAS is now calibrated. Please repeat calibration if you move the dash camera. Please
note in adverse weather ADAS may not be as accurate. Please recalibrate frequently to ensure
the best accuracy is achieved.

Call 01255 555200
Email [e-mail]
Visit www.durite.co.uk
TECHNICAL DRAWING
TECHNICAL SPECIFICATIONS
The information contained in this document is correct to the best of our knowledge and subject to change at any time without notice.
TECHNICAL SPECIFICATIONS
Type 2.0 MP 1080p ADAS Dash Camera
View Angle 170°
Resolution Rate 1080p, 720p, VGA
Frame Rate 30FPS
2nd Camera N/A
Video Compression Format MOV
Screen Size 3.0” IPS (640*360)
OperatingTemperature / StorageTemperature -20°C to +70°C / -30°C to +80°C
Memory Card 8-128GB Class 10 or higher
Standard Voltage / Ampage 5VDC / 2.5A
Night Viewing Distance 10 Metres with headlights
Battery Yes - 180mAh
GPS Yes
G Sensor Yes
Parking Guard Yes
Motion Detection Yes
ADAS Yes - LDW / FCW
Certicates CE