DUROMAX XP10000EH User manual

Product Support (Product: information, application, service info & warranty questions)
or call 1-800-629-3325 (option 3) Monday -Thursday 6am to 7pm, Friday 6am to 5:30pm. PST
[email protected]

Page 2 of 29

The generator is a potential source of electrical shock if misused. Do not expose the generator to
These labels warn you of potential hazards that can cause serious injury. Read them carefully.
moisture, rain or snow. Do not let the generator get wet, and do not operate it with wet hands.
Page 3 of 29

Read and understand this instruction manual before operating your generator. You can help prevent
accidents by being familiar with your generator’s controls, and by observing safe operating
procedures.
Operator Responsibility
Know how to stop the generator quickly in case of emergency.
Understand the use of all generator controls, output receptacles, and connections.
Do not let children operate the generator without parental supervision.
Carbon Monoxide Hazards
Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust
can cause loss of consciousness and may lead to death.
If you run the generator in an area that is confined, or even partially enclosed, the air you breathe
could contain a dangerous amount of exhaust gas. To keep exhaust gas from accumulating,
provide adequate ventilation.
Electric Shock Hazards
The generator produces enough electric power to cause a serious shock or electrocution if misused.
Using a generator or electrical appliance in wet conditions, such as rain or snow, or near a pool or
sprinkler system, or when your hands are wet, could result in electrocution. Keep the generator dry.
If the generator is stored outdoors, unprotected from the weather, check all of the electrical
components on the control panel, before each use. Moisture or ice can cause a malfunction or short
circuit in electrical components, which could result in electrocution.
Do not connect to a building electrical system unless a qualified electrician has installed an isolation
switch.
Fire and Burn Hazards
The exhaust system gets hot enough to ignite some materials.
－Keep the generator at least 3 feet (1 meter) away from buildings and other equipment during
operation.
－Do not enclose the generator in any structure.
－Keep flammable materials away from the generator.
The muffler becomes very hot during operation and remains hot for a while after stopping the
engine.
Be careful not to touch the muffler while it is hot. Let the engine cool before storing the generator
indoors.
Gasoline is extremely flammable and is explosive under certain conditions. Do not smoke or allow
flames or sparks where the generator is refueled or where gasoline is stored. Refuel in a
well-ventilated area with the engine stopped.
any spilled fuel has been wiped up before starting the generator.
Fuel vapors are extremely flammable and may ignite after the engine has started. Make sure that
SAFETY INFORMATION
Page 4 of 29

Page 5 of 29
CONTENTS
FEATURES................................................................................................................. 2
SAFETY INFORMATION........................................................................................ 3 - 4
CONTENTS................................................................................................................ 5
COMPONENT IDENTIFICATION........................................................................ 6 - 8
WATTAGE REFERENCE CHART........................................................................ 9
SPECIFICATIONS.................................................................................................... 10
ASSEMBLY................................................................................................................ 11
PRE-OPERATION CHECK..................................................................................... 12
STARTING THE ENGINE (GASOLINE).............................................................. 13
STARTING THE ENGINE (LPG)........................................................................... 14
OPERATING INSTRUCTIONS.............................................................................. 15 - 17
MAINTENANCE....................................................................................................... 18 - 20
STORAGE.................................................................................................................. 21
WHEEL KIT INSTALLATION.............................................................................. 22
SERVICE INFORMATION..................................................................................... 23 - 29

Page 6 of 29

Engine Key
To start and stop the engine.
Key position:
OFF: To stop the engine. Key can be removed / inserted.
START: To start the engine by operating the starter motor.
Do not turn the key switch to START position when the engine is running to
Recoil Starter
Do not allow the starter grip to snap back against the engine. Return it gently to prevent damage to the starter.
.
Voltage Selector Switch
The voltage selector switch switches the main power carrying windings of the generator to produce
‘‘120V ’’ or ‘‘120/240V’’. If a 240V appliance is connected to the 4-prong receptacles, the switch
Switch Position
120/240V: The 120V and 120/240V receptacles can be used simultaneously.
Fuel Valve Lever
The fuel valve is located between the fuel tank
and carburetor. When the valve lever is in the ON
position, fuel is allowed to flow from the fuel tank
to the carburetor. Be sure to return the fuel valve
lever to the OFF position after stopping the
en
g
ine.
Choke Rod
The choke is used to provide an enriched fuel
opened and closed by operating the choke rod
manually. Pull the rod out toward CLOSED to
enrich the mixture for cold starting
ON: To run the engine after starting, or to pull start the unit.
prevent damage to the starting motor.
To start the engine, turn the key to on, pull the starter grip lightly until resistance is felt, then pull briskly.
mixture when starting a cold engine. It can be
must be in the ‘‘120/240V’’ position. If only a 120V appliance is being connected select the "120V"
position.
120V: Do not use the 120/240V twist lock receptacle in this position. The most power will be available
at the 50A 120/240V receptacle.
Page 7 of 29

Change the Voltage Selector Switch after turning the AC circuit breaker to OFF. The generator may
Ground Terminal
The generator ground terminal is connected to the frame of the generator, the metal
non-current-carrying parts of the generator, and the ground terminals of each receptacle.
DC Receptacle
The DC receptacle may ONLY be used for charging 12 volt automotive type batteries.
The battery must be connected to the generator DC receptacle with the proper polarity (battery
positive to generator positive (+) and battery negative to the generator negative (-).
Do not start the vehicle while the battery charging cable is connected and the generator is running.
The vehicle or the generator may be damaged.
DC Circuit Protector
The DC circuit protector automatically shuts off the DC battery charging circuit when the DC
charging circuit is overloaded, when there is a problem with the battery, or when the connections
between the battery and the generator are improper.
Oil Alert System
The Oil Alert system is designed to prevent engine damage caused by an insufficient amount of oil in
the crankcase. Before the oil level in the crankcase can fall below a safe limit, the Oil Alert system
will automatically stop the engine (the engine switch will remain in the ON position). The Oil Alert
system should not take the place of checking the oil level before each use.
If the engine stops and will not restart, check the engine oil level before troubleshooting in other areas.
AC Circuit Breaker
The AC circuit breaker will automatically switch OFF if there is a short circuit or a significant
overload of the generator at the receptacle. If the AC circuit breaker is switched OFF automatically,
check that the appliance is working properly and does not exceed the rated load capacity of the circuit
before switching the AC circuit breaker ON again. The AC circuit breaker may be used to switch the
generator power ON or OFF.
AC Circuit Protector
The AC circuit protectors will automatically switch OFF if there is a short circuit or a
significant overload of the generator at the 20A 120V, 30A 120V plug. If an AC circuit
protector switches OFF automatically, check that the appliance is working properly and
does not exceed the rated load capacity of the circuit before resetting the AC circuit
protector ON.
be damaged if the Voltage Selector Switch is changed with the breaker in the ON position.
Page 8 of 29

WATTAGEREFERENCECHART
Electric equipment, especially engines produce strong current when being started. The table below offers references
when you connect those installations to generator.
Tool or Appliance Rated* (Running) Watts Additional Surge (Starting) Watts
Essentials
Light Bulb-75 watt 75 -
Sump Pump 800 1200
Refrigerator/Freezer-18 Cu. Ft. 800 1600
Water Well Pump-1/3 HP 1000 2000
Heating/Cooling
Window Air Conditioner-10000 BTU 1200 1800
Window Fan 300 600
Furnace Fan Blower-1/2 HP 800 1300
Kitchen
Coffee Maker 1500 -
Electric Stove- Single Element 1500 -
Hot Plate 2500 -
Family Room
DVD/CD Player 100 -
VCR 100 -
Stereo Receiver 450 -
Color Television- 27” 500 -
Personal Computer w/17” Monitor 800 -
Other
Security System 180 -
AM/FM Clock Radio 300 -
Garage Door Opener- 1/2 HP 480 520
Electric Water Heater- 40 Gallon 4000 -
DIY / Job Site
Quartz Halogen Work Light 1000 -
Airless Sprayer- 1/3 HP 600 1200
Reciprocating Saw 960 960
Electric Drill- 1/2 HP 1000 1000
Circular Saw- 7 1/4” 1500 1500
Miter Saw- 10” 1800 1800
Table Planer- 6” 1800 1800
Table Saw / Radial Arm Saw- 10” 2000 2000
Air Compressor- 1- 1/2 HP 2500 2500
*Wattages listed are approximate only. Check tool or appliance for actual wattage.
Deep Freezer 500 800
Microwave Oven-1000 watt 1000 2000
Page 9 of 29

SPECIFICATIONS
Generator
Frequency 60 HZ
Max. AC Output 10000 Watt
Rated AC Output 8000 Watt
Run Time 8 hour
Engine
Type Air Cooled, OHV, 4-Stroke
Displacement 419 cc
Output 16.0 HP / 3600 rpm
Oil Alert Standard
Standard
Features
Air Cleaner Standard
Voltmeter Standard
Receptacle
2×NEMA 5-20R
1×NEMA 5-30R
1×NEMA L14-30R
1×NEMA 14-50R
Plug(Not included with
your generator)
2×NEMA 5-20P
1×NEMA 5-30P
1×NEMA L14-30P
1×NEMA 14-50P
Voltage Selector Standard
DC Circuit Breaker Standard
AC Circuit Breaker Standard
AC Circuit Protector Standard
AC Receptacle 2 Pole 120V AC
3 Pole 120V/240V AC
Dimensions
Length 34"
Width 27"
Height 32"
Gross Weight 240 lbs.
Decibel <72 dBA
Battery 12V 18A/hr
Model XP10000EH
Model 16HP DuroMaxOHVGeneratorEngine
Fuel Unleaded Gasoline /LPG(LiquidPropaneGas)
GasTank Capacity 8.3 Gallon
Muffler Standard
DC ReceptaclesStandard
Fuel Gauge 8.3 Gallon
Page 10 of 29

ASSEMBLY
Wheel Kit Installation
3Install the two stands on the under frame using the flange nuts.
handling. PRE-OPERATION CHECK
Engine Oil
Engine oil is a major factor affecting engine performance and
service life. Non-detergent and 2-stroke engine oils will damage
the engine and are not recommended.
 Check the oil level BEFORE EACH USE with the
generator on a level surface and the engine stopped.
Use 4-stroke motor oil that meets or exceeds the
1Install the splitaxle assembly on the generator.
2Install the two wheels on the axle shaftsusing the flange nuts.
requirements for API service classification SAE.
Negative Battery Cable
Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after
1 The negative battery cable of your unit will be disconnected on arrival due to shipping
restrictions.
2 Connect the negative battery cable found tucked up and to the right of the battery to the
negative battery terminal using the provided nut and bolt.
Page 11 of 29

SAE 10W-30 is recommended for general, all-temperature use. Other viscosities shown in the
chart may be used when the average temperature in your area is within the indicated range.
1Remove the oil filler cap and wipe the dipstick clean.
2Check the oil level by inserting the dipstick into the filler neck without screwing it in.
3If the level is low, fill to the top of the oil filler neck with the recommended oil.
Fuel
Check the fuel gauge, and refill the tank if the fuel level is low.
Refuel carefully to avoid spilling fuel. Do not fill above the shoulder of the fuel strainer.
Gasoline is highly flammable and explosive, and you can be burned or seriously injured when
refueling.
● Refuel only outdoors.
● Wipe up spills immediately.
Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life.
Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or water in the
fuel tank.
Use unleaded gasoline with a octane rating of 86 or higher.
●Besuretoshuttheenginedownandkeep heat, sparks, and flame away.
This engine is certified to operate ONLY on unleaded gasoline orLPG.
Page 12 of 29

Push the choke to the OPEN position as the engine warms up.
3The choke will need to be closed, pull the choke rod out to the CLOSED position.
3Turn the fuel valve lever to the OFF position.
2Turn the engine switch to the OFF position.
1Turn the AC circuit breaker to the OFF position. Disconnect DC battery charging cables.
In normal use:
To stop the engine in an emergency, move the engine switch to the OFF position.
When the engine starts, allow the engine switch to return to the ON position.
be recharged.
If the speed of the starter motor drops after a period of time, it is an indication that the battery should
release the switch and wait 10 seconds before operating the starter again.
Operating the starter motor for more than 5 seconds can damage the motor. If the engine fails to start,
engine starts.
2Turn the fuel valve lever to the ON position.
start if a load is connected.
1Make sure that the AC circuit breaker is in the OFF position. The generator may be hard to
4Turn the engine switch to the START position and hold it there for 5 seconds or until the
In an emergency:
Stopping the Engine
Page 13 of 29

2Turn the engine switch to the OFF position.
1Turn the AC circuit breaker to the OFF position. Disconnect DC battery charging cables.
In normal use:
To stop the engine in an emergency, move the engine switch to the OFF position.
In an emergency:
Stopping the Engine
When the engine starts, allow the engine switch to return to the ON position.
be recharged.
If the speed of the starter motor drops after a period of time, it is an indication that the battery should
release the switch and wait 10 seconds before operating the starter again.
Operating the starter motor for more than 5 seconds can damage the motor. If the engine fails to start,
start if a load is connected.
1Make sure that the AC circuit breaker is in the OFF position. The generator may be hard to
2 Turn the gasoline fuel valve to the "OFF" position.
3 Connect the propane gas hose to the regulator/decompression valve.
4 Connect the propane gas collar to the gas supply and then turn on the propane gas supply.
5 Press the button on top of the pressure release valve down two or three times.
3Turn the off the propane gas supply.
i. Wait 30 seconds and then push the choke lever all the way to the "OPEN" position.
a. If the engine is warm (the unit was run recently) start with the choke half open.
6 The choke operates differently on propane gas.
b. If the engine is cold (the unit was not run recently) start with the choke "OPEN".
7 Turn the engine key switch to the START position and hold it there for 5 seconds, or until the
engine starts.
Decompression
Valve / Regulator
Connect to propane
gassupply.
Page 14 of 29

M
£
Make sure that it is in good working order. Faulty appliances or power cords can create a
Before connecting an appliance or power cord to the generator:
AC Applications
wire.
ground terminals in the AC output receptacles. The system ground is not connected to the AC neutral
The portable generators have a system ground that connects generator frame components to the
Ground System
utility power is restored. Consult the utility company or a qualified electrician.
contact the lines during a power outage, and the generator may explode, burn, or cause fires when
back feed into the utility lines. Such back feed may electrocute utility company workers or others who
Improper connections to a building electrical system can allow electrical current from the generator to
power, is prerequisite.
applicable laws and electrical codes. A transfer switch, which isolates generator power from utility
The connection must isolate the generator power from utility power, and must comply with all
Connections for standby power to a building electrical system must be made by a qualified electrician.
Connections to a Building Electrical System
OPERATING INSTRUCTIONS
OFF, but will shorten the service life of the generator.
operation or slightly overloading the generator may not switch the circuit breaker or circuit protector
Substantial overloading will open the circuit breaker. Exceeding the time limit for maximum power
maximum may be used for no more than 30 minutes.
Never exceed the maximum power rating of the generator. Power levels between rated and
Make sure that the electrical rating of the tool or appliance does not exceed that of the generator.
the rated load capacity of the generator has been exceeded.
immediately. Disconnect the appliance, and determine whether the problem is the appliance, or if
If an appliance begins to operate abnormally, becomes sluggish or stops suddenly, turn it off
potential for electrical shock.
Page 15 of 29

AC Operation
2Turn the voltage selector switch to either position.
With the voltage selector switch in the ‘‘120/240V’’ position, you can use the 120V and 120/240V
3Switch the AC circuit breaker ON.
4Plug in the appliance.
Most motorized appliances require more than their rated power for startup.
AC circuit breaker or AC circuit protector to switch OFF, reduce the electrical load on the circuit, wait
a few minutes and then reset the AC circuit breaker or AC circuit protector.
AC Receptacle Selection
The generator has two separate main power producing circuits. These two circuits supply equal power
to different receptacles shown when the voltage selector switch is in the 120/240V position.
When two or more receptacles are used; prevent overloading by dividing the load between the two
power circuits.
The chart below shows the rated load in amperes that can be connected to each receptacle to balance
the generator.
Main Power Circuit Receptacles Powered by
Each Main Circuit Power Distribution
Main Circuit 1 2 and 5 2+5=32.5 A Rated
Main Circuit 2 1 and 4 1+4=32.5 A Rated
The table shows the specifications when the 120/240V locking plug receptacle is used for 120V.
1Start the engine .
Do not exceed the current limit specified for any one receptacle. If an overloaded circuit causes the
The total rated ampere draw is 65A in 120V ONLY.
receptacles simultaneously. If you \ require more 120V only power, then select the "120V only" position
this will disable the 120/240V twist lock plug.
Page 16 of 29

DC Operation
The DC terminals may ONLY be used for charging 12 volt automotive type batteries.
Connecting the battery cables:
1Before connecting the battery charging cables to a battery that is installed in a vehicle,
disconnect the vehicle ground battery cable from the battery negative (－) terminal.
ventilation when charging or using batteries.
Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands
after handling.
2Connect the positive (＋) battery cable to the battery positive (＋) terminal.
3Connect the negative (－) battery cable to the battery negative (－) terminal.
4Connect the plug of the battery cable to the generator DC receptacle.
5Start the generator.
Do not start the vehicle while the battery charging cable is connected and the generator is running.
The vehicle or the generator may be damaged. An overloaded DC circuit, excessive current draw by
the battery, or a wiring problem will trip the DC circuit protector. If this happens, wait a few minutes
before pushing in the circuit protector to resume operation.
Disconnecting the battery cables:
1Stop the engine.
2Disconnect the plug of the battery cable to the generator DC receptacle
3Disconnect the other end of the negative (－) battery cable from the battery negative (－)
terminal.
4Disconnect the other end of the positive (＋) battery cable from the battery positive (＋)
terminal.
Batteries give off explosive gases; keep sparks, flames and cigarettes away. Provide adequate
5Reconnect the vehicle ground battery cable to the battery negative (－) terminal.
(1,500 meters), have a dealer perform this carburetor modification. This engine, when operated at
carburetor may cause the engine to overheat and result in serious engine damage.
lean for low altitude use. Operation at altitudes below 5,000 feet (1,500 meters) with a modified
When the carburetor has been modified for high altitude operation, the air/fuel mixture will be too
greater than this if no carburetor modification is made.
3.5% for each 1,000-foot (300-meter) increase in altitude. The effect of altitude on horsepower will be
throughout its useful life. Even with carburetor modification, engine horsepower will decrease about
high altitude with the carburetor modifications for high altitude use, will meet each emission standard
modifications to the carburetor. If you always operate your generator at altitudes above 5,000 feet
periods of time, may increase emissions. High altitude performance can be improved by specific
starting. Operation at an altitude that differs from that at which this engine was certified, for extended
and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard
At high altitude, the standard carburetor air/fuel mixture will be too rich. Performance will decrease,
High Altitude Operation
Page 17 of 29

MAINTENANCE
The Importance of Maintenance.
Good maintenance is essential for safe, economical, and trouble-free operation. It will also help
reduce air pollution.
Improper maintenance, or failure to correct a problem before operation, can cause a malfunction in
which you can be seriously injured or killed.
Always follow the inspection and maintenance recommendations and schedules in this instruction
manual.
Maintenance Safety
Make sure the engine is off before you begin any maintenance or repairs.
Let the engine and exhaust system cool before touching.
To reduce the possibility of fire or explosion, be careful when working around gasoline. Use only
a nonflammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away
from all fuel-related parts.
Maintenance Schedule
Remember that this schedule is based on the assumption that your machine will be used for its
designed purpose. Sustained high-load or high-temperature operation, or use in unusually wet or dusty
conditions, will require more frequent service.
REGULAR SERVICE PERIOD（2）Before First Every3 Every6 Every
each month months months year or
use or 20 or 50 or 100 300
Hrs. Hrs. Hrs. Hrs
ITEM
Performed at every indicated month or
operating hour interval, whichever
comes first.
●Engine oil Check ○
●Air cleaner Check ○
Clean
○(1)
●○
Sediment cup Clean
●Spark plug Clean-Adjust
○
Replace ○
●○
Spark arrester Clean
●○
Idle speed Check-Adjust
●○
Valve clearance Check-Adjust
●Combustion
chamber Clean After every 500 Hrs.
●Fuel tank and Clean
filter
○
●Fuel tube Check Every 2 years(replace if necessary)
(1) Service more frequently when used in dusty areas.
(2) For commercial use, log hours of operation to determine proper maintenance intervals.
Change ○
Page 18 of 29

Engine Oil Change
Drain the oil while the engine is warm to assure rapid and complete draining.
1Remove the drain plug and sealing washer, remove the oil filler cap, and drain the oil.
2Reinstall the drain plug and sealing washer. Tighten the plug securely.
3Refill with the recommended oil and check the oil level.
Wash your hands with soap and water after handling used oil.
Air Cleaner Service
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction, service
the air cleaner regularly. Service more frequently when operating the generator in extremely dusty
areas.
Never run the generator without the air filter. Rapid engine wear will result.
1Unsnap the air cleaner cover clips, remove the air cleaner cover, and remove the element.
2Wash the air cleaner element in a solution of household detergent and warm water, then rinse
thoroughly, or wash in nonflammable or high flashpoint solvent. Allow the air cleaner
element to dry thoroughly.
3Soak the air cleaner element in clean engine oil and squeeze out the excess oil. The engine
will smoke during initial startup if too much oil is left in the air cleaner element.
4Reinstall the air cleaner element and the cover.
Page 19 of 29

sediment cup should be cleaned.
1Turn the fuel valve lever to the OFF position.
nonflammable or high flash point solvent.
4Turn the fuel valve lever ON and check for leaks.
Spark Plug Service
To ensure proper engine operation, the spark plug must be properly gapped and free of deposits.
If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler.
1Remove the spark plug cap.
2Clean any dirt from around the spark plug base.
3Use a spark plug wrench to remove the spark plug.
4Visually inspect the spark plug. Discard it if the insulator is cracked, chipped or fouled.
5Measure the plug gap with a feeler gauge. Correct as necessary by carefully bending the side
electrode.
3Reinstall the filter, O-ring, and sediment cup.
The gap should be: 0.028 0.031 in (0.70 0.80 mm)
6Check that the spark plug washer is in good condition, and
thread the spark plug in by hand to prevent cross-threading.
7After the spark plug is seated, tighten with a spark plug
wrench to compress the washer.
－If installing a new spark plug, tighten 1/2 turn after the spark plug
seats to compress the washer. If reinstalling a used spark plug,
tighten 1/8 －1/4 turn after the spark plug seats to compress the
washer.
The spark plug must be securely tightened. An improperly tightened spark plug can become very hot
and could damage the engine. Never use spark plugs which have an improper heat range.
Remove the sediment cup, O-ring, and filter.
2Clean the sediment cup, O-ring, and filter in
Fuel Sediment Cup Cleaning
The sediment cup prevents dirt or water, which may be
in the fuel tank from entering the carburetor. If the
engine has not been running for a long time, the
Page 20 of 29