Dvico FusionHDTV 7 Cool User manual

FusionHDTV 7 Cool
1Before Getting Started ...............................................................................2
1.1 FusionHDTV Specification.......................................................................................................... 2
1.2 FusionHDTV System Requirements........................................................................................... 4
1.3 Package contents....................................................................................................................... 5
2Software Installation...................................................................................6
2.1 Installing FusionHDTV Applications............................................................................................ 6
2.2 Driver installation.......................................................................................................................11
3Hardware Installation ...............................................................................13
3.1 About the Board........................................................................................................................ 13
3.2 Before Installation PCI card...................................................................................................... 14
3.3 PCI Board Installation............................................................................................................... 14
3.4 Remote Installation................................................................................................................... 15
4Using FusionHDTV...................................................................................16
4.1 Starting and Quitting................................................................................................................. 16
4.2 Display setup............................................................................................................................ 16
4.3 Using FusionRemote................................................................................................................ 20
4.4 FusionHDTV Shortcut Key ....................................................................................................... 21
5Technical Support ....................................................................................22

All specifications and information are subject to changes without further notices 2
1 Before Getting Started
1.1 FusionHDTV Specification
A Highly cost effective reception card
You can enjoy HDTV at quite a low price due to Dvico’s innovative HDTV software decoding engine.
Unrivaled crystal-clear picture quality
FusionHDTV provides up to 5 times higher resolution when compared to analog TV, and provides
crisp and crystal-clear picture quality to a PC screen.
Good picture quality on LCD or low-resolution monitor
FusionHDTV shows excellent and super-clear on HDTV screens and even on LCD TV’s and low
resolution CRT due to Dvico’s proprietary decoding engine.
Great system compatibility
FusionHDTV is compatible with most video cards and motherboards. FusionHDTV works on any
recent VGA cards including Nvidia MX series or later chipsets, as well as ATI Radeon chipsets. It
works quite well on Intel, VIA, SIS, and other motherboard chipsets. Minimum system requirements
are Pentium 4 1.6G and DDR266 memory (or RDRAM memory), or AMD’s Athlon™ XP 1600+ or
faster processor, if you don’t have the ATI Radeon VGA card. Pentium 3 800Mhz or faster will be
enough if you have an ATI Radeon card.
Recording and playback of the HDTV stream
You can record live HDTV broadcasting streams to a PC and play them back anytime you want. You
can select the single sub-channel or whole stream recording when you hit recording button.
Using the most recent tuner
FusionHDTV uses the most recent tuner to get the best reception rate, so you can get the un-interrupted
and stable HDTV screen.
69 terrestrial digital (8VSB)/analog channels
FusionHDTV supports 69 terrestrial digital (8VSB) and analog channels. So you can lose no channels at
all.
8VSB/64QAM/256QAM reception support
FusionHDTV works either with free to air digital TV(8VSB) and unencrypted digital cable TV(QAM)
broadcasting channels. So you will have the ability to receive all the channels available to you at your
location.
All 18 ATSC formats compliant
FusionHDTV supports all of the 18 formats of ATSC broadcasting, so you can experience the all of the
full ATSC format-rich content available.
Support analog Video Signal Capture
You can capture analog video signal (Composite and SVHS) and save it to WMV/AVI format.
Supports S/PDIF audio output thru sound card
It can bypass the audio to digital output and connect directly to an AV amplifier.
High resolution still capture
FusionHDTV provides high resolution still screen capturing capability in live playback as well as file
playback mode.

All specifications and information are subject to changes without further notices 3
Cut-on-the-fly feature – Cut the transport stream files
You can cut out the wanted scenes from the captured file and reconstruct the Digital clip.
Supports sub-channel
Sub channel is listed up in sub channel play list and can be selected with channel up/down button or
mouse selection in sub channel play list.
Second language
Supports the second language in digital broadcasting.
Supports screen saver off.
Screen saver is off while FusionHDTV runs.
Add To Favorite List
You can add your favorite programs into favorite list before watching them.
Time Shifting
FusionHDTV provides the various file playback functions just like live TV mode. That is, pause/ instant
replay/ time-shifting by scroll bar/ fast-forward/ fast-rewind.
Being interrupted while watching live TV programs (such as pick up phone calls & answer the door), all
you need to do is simply press the Pause button and freeze the picture for a period of time, and then
pick up right where you left off.
The FF/REW Function is available Windows XP Service Pack 2 or above
Supports PIP (Picture in Picture)
The FusionHDTV is like having two TVs in one! With the Picture in Picture (PIP) function you can now
watch two of your favorite programs all on a single screen.
Supports Multi-View
You can see all sub channel video on the single video screen.
- This function is available under Windows XP or higher to be installed.
- The multi-View function is available without Time-shifting or analog channel.
- When the Full screen mode, this function doesn't work at this moment.

All specifications and information are subject to changes without further notices 4
1.2 FusionHDTV System Requirements
System requirements for FusionHDTV are as follows
<Input/Output>
Antenna
S-Video IN, Composite IN
<DxVA VGAs>
Pentium3 800MHz or faster with 128M memory
Celeron 900Mhz or faster with 128M memory
GeForce4 MX420,440,Fx5200,5600 Series or late all models.
Pentium M 1.4GHz or faster for notebook PC
All ATI Radeon series VGAs
Windows 2000/XP/MCE 2005/Vista 32bit/Vista 64bit
Ultra-DMA66 enabled main board and HDD for recording
<nonDxVA VGAs>
Pentium4 1.6GHz or faster with 128M memory
All Nvidia MX series VGAs and ATI Radeon series VGAs
All Matrox series VGAs
DDR266 or faster memory
Windows 2000/XP/MCE 2005/Vista 32bit/Vista 64bit
Ultra-DMA66 enabled main board and HDD for recording

All specifications and information are subject to changes without further notices 5
1.3 Package contents
The FusionHDTV package contains the following items. Some packages may change depending on other
conditions.
①FusionHDTV card
②SetupCD
③Manual
* FusionHDTV remote transceiver.
①FusionHDTV transceiver
②External connection cable (Include the IR remote receiver)
* Do not connect the line-in cable because FusionHDTV 7 Cool is supporting the external sound internally.
1 2
1 2 3

All specifications and information are subject to changes without further notices 6
2 Software Installation
Most likely there will be an updated version of the files on our web site.
Please check the site (http://www.FusionHDTV.co.kr/Eng) before you install the software included in the CD.
2.1 Installing FusionHDTV Applications
Insert FusionHDTV Installation CD into the CD-ROM drive. The setup window will automatically pop up. if
you downloaded the recent version on DVICO’s website, please run install.exe or setup.exe.
2.1.1 Uninstall Drivers
1) When you select Uninstall Driver in the menu on the FusionHDTV INSTALLER program, Select
your FusionHDTV board type.
2) When all the drives are removed, you will see following message.
To remove the 64bit driver, you may remove the driver by "Control panel-Add or Remove programs".

All specifications and information are subject to changes without further notices 7
2.1.2 Installing FusionHDTV Software
Important: Installation on Windows 2000 Professional or Windows XP
Before you install FusionHDTV software, be sure that you logged on as an account with
Administrator privileges.
1) Select “Install FusionHDTV”.
2) At the FusionHDTV Installation dialog
opens, click on the “Next>” button.
3) The “Choose Destination Location”
window will appear. Click on “Next” if
you want to install the FusionHDTV in
the default directory. Otherwise, you
can choose a different directory by
clicking on “Browse”.
4) Press “Next” on the Destination
Folder selection window.

All specifications and information are subject to changes without further notices 8
5) The “Setup status” window will appear.
6) Choose your country, then click “OK”.
7) PC specification selection windows will
appear. Please select the appropriate
system. You can change the mode after
installation with configuration menu of the
application program. You do not need to
reinstall the program with different options.
8) Select your FusionHDTV card(FusionHDTV7
Cool), and Press ‘Install Driver’ to install
latest drivers.

All specifications and information are subject to changes without further notices 9
9) The Driver Installer appears. Press
‘Next’.
10) If you connect 2 card or above, Press “YES”
and then re-install another driver, but if you
have 2 same card, you may press “NO”.
11) Press “Continue Anyway” for the digital signature message.
12) Following message indicates the completion of the setup.
13) By clicking the Finish button, the
software installation is done.
14) When you reboot, the system will
ask for the one driver. Please click
“Yes” when the digital signature
window appears.
<Notes>
In certain cases, Windows will ask for the .sys files. You can locate the sys files in the C:\Program
Files\DVICO\FusionHDTV\driver\Cool or C:\Windows\System32\Drivers folder.

All specifications and information are subject to changes without further notices 10
2.1.3 Installing Microsoft DirectX 9
Important! Installing on Windows 2000 Professional or Windows XP
You can check the version of DirectX by typing “dxdiag” on the command line which appears with
menu selection “start->run”
If you have DirectX 9 or later already, you
do not need to install DirectX 9 again.
1) Run ‘Install.exe’ and then select
“Install Direct 9”.
2) Read the License Agreement
carefully and check “I accept the
agreement” and then click on “Next” if
you agree.
3) To start installing of DirectX 9.0
Runtime, click on “Next”.
Tip If there is a DirectX already installed
in the system, a different window will show up
instead of the one above.
4) Click on “Finish” to restart system
and complete installation of the
DirectX.

All specifications and information are subject to changes without further notices 11
2.2 Driver installation
2.2.1 Installing driver
If you already installed the FusionHDTV software, insert the FusionHDTV board into the PCI local bus
slot.
In certain cases, Windows will ask for the .sys files. You can locate the sys files in the C:\Program
Files\DVICO\FusionHDTV\driver\COOL or C:\Windows\System32\Drivers folder.
1) When the “Add New Hardware Wizard window” appears, select “Install the software automatically
(Recommended)” and then click “next”.
2) When the “FusionHDTV7 Cool, Unified AVStream” window appears, Click “Continue Anyway”.
3) After files are copied, Click “Finish” if the “FusionHDTV7 Cool, Unified AVStream” driver is properly
installed.

All specifications and information are subject to changes without further notices 12
2.2.2 Checking the driver
Right click the “My Computer” icon and select “properties” from the popup menu. Select Hardware-> Device
Manger. You must see following devices properly installed under the “Sound video and game controllers”.
If you want to remove the driver, select Uninstall Driver in the menu on the FusionHDTV INSTALLER
program, Select your FusionHDTV board type.
To remove the 64bit driver, You may remove the driver by "Control panel-Add or Remove programs".

All specifications and information are subject to changes without further notices 13
3 Hardware Installation
3.1 About the Board
[FusionHDTV7 Cool]
Antenna: Connects to the terrestrial signal or cable
VIDEO-IN: For external video sources.
To use the S-video input, do not connect the composite video (yellow) cable.
Do not connect the line-in cable because FusionHDTV 7 Cool is supporting the external sound internally.
Antenna
VIDEO-IN

All specifications and information are subject to changes without further notices 14
3.2 Before Installation PCI card
Warning:
1) Before installing, first touch the grounded part of the PC to protect the components on the board
from static electricity.
2) Before installing the board, the system’s power should be turned off. Installing the Board when the
system’s power is “ON,” will damage the system or the Board and void your warranty.
3) Please remove the power cord from the PC.
4) Loosen the computer cover screws and remove the cover.
3.3 PCI Board Installation
1) Insert the board by holding the top part of the board and push it until it completely locks into the slot.
Fasten the screw on the bracket using a screw driver.
Do not connect the line-in cable because FusionHDTV 7 Cool is supporting the external sound internally.
To use the S-video input, do not connect the composite video (yellow) cable.
Tip After the board installation, when the power is on, the driver search message will appear. Please
refer to chapter 2 for driver Installation.

All specifications and information are subject to changes without further notices 15
3.4 Remote Installation
1) Connect the enclosed converting cable on the TV
card.
2) After IR receiver and FusionHDTV remote software is installed, please reboot and start the
configuration by right clicking the FusionRemote icon at the low right bottom of the screen. If you
want to see the FusionRemote icon in the tray, please start the program by Start->Program-
>DViCO->FusionRemote.
3) Please select the port that IR receiver module is attached and press the any button on the remote
transceiver. ADialog box with the remote transceiver buttons will appear.
Tip FusionRemote program will start automatically when the PC is booted. You can check the Fusion
Remote program availability at the Task Bar of Windows like the picture below.
“Select the Remote device to ‘HDTV Cool / 7 USB’ on the Port tab.”

All specifications and information are subject to changes without further notices 16
4 Using FusionHDTV
Please check Http://www.FusionHDTV.co.kr for any updated software or manuals.
4.1 Starting and Quitting
Click Start, point to Program->DVICO->FusionHDTV, or double click on the FusionHDTV icon in the program
folder to execute FusionHDTV.
When you first execute the program, it will ask for a channel scan. Please say “Yes” for the channel scan.
By clicking (Exit Button), the software is terminated.
4.2 Display setup
FusionHDTV Software composed with View panel and control panel.
4.2.1 Video Window
It shows the HDTV picture inside the window.
[ Single mode ]
[ PIP mode ]
If you click right on the video window, a popup menu will appear.

All specifications and information are subject to changes without further notices 17
Configuration: is used to configure the setting
Show Controller: Show/Hide FusionHDTV’s controller.
Show Outline: is used to show the outline of video window
Show Channel Manager: Show/Hide channel manager.
Recording Scheduler : is used to Reservation Record.
Input Source: is used to change input source.
Favorites Channel : Add your favorite programs into favorite list before
watching them.
Add to Favorite Channel.
Display Size: Resize display.
Aspect Ratio: Adjust display ratio.
TV Analog De-interlacing: removes interlace to progressive conversion
artifact.
Analog Color inverse
Analog TV multi Audio
Always On Top: Shows FusionHDTV application always on top.
Second language : Second language can be heard with checking
"Audio > Second Language" option when it is available in digital broadcasting.
Show WallPaper(ALT-W)
Time-Shifting On/Off : Change Time-Shifting mode.
MultiView : You can see all sub channel video on the single video screen.
PIP : Change PIP on/off , toggle PIP program and select PIP TV tuner. If you have a single Tuner, you can
see sPIP instead of PIP.
Sleep Mode : Shut down the system or program when specified time while HDTV runs.
File Playback: Play input signal(or file).
Stop : Change Stop.
Help: Shows Help information.
About..: Shows Program Information
Exit: Quit FusionHDTV.

All specifications and information are subject to changes without further notices 18
4.2.2 Controller
This indicates Control Buttons.
1) Exit button
2) Maximize button
3) Minimize
4) Channel UP/DOWN button
5) Show Input source.
6) Channel/Input button: This mode shows the channel number. If you click on the small channel
sub number(2), it will show the channel list and sub channel name.
7) Video/Audio status
8) Show program name.
9) Show signal strength : you can toggle to current time in the configuration-display-show as hh:mm:ss.
10) Time: Total elapsed time played.
11) Expand menu button : shows the expand menu.
12) Volume: Shows and controls the current volume level.
13) EPG button: Show present/following EPG.
14) LiveTV button: Changes to live TV mode. When the time-shifting is OFF, this button operates with
time-shifting.
15) Input button: is used to select input signal.
16) Cut Edit button: is used to edit a recorded file. This button is used the A-B Repeat function when the
time-shifting.
17) Mark in button: Mark in the start point where the cut starts.
18) Mark out button: Mark in the end point where the cut ends.
19) Open file button: is used to open recorded files.
20) Slow Rewind button
21) Slow Fast Forward button
22) Time moving slider: Shows location currently playing. If you drag it with the mouse, you can move
anywhere in the white line.
23) Time moving Bar: Is used to drag the slider bar.
12
3
4 5 6
7
8 9
10
11 12
13 14 15 16 17 18 19 20 21
22
23
2425 26 27 28 29 30 31
32

All specifications and information are subject to changes without further notices 19
24) Teletext button: is not used.
25) PIP button : is used to show the PIP screen. This button is available with dual digital or multi card.
PIP controller : Dual digital model or multi-card
If you click the PIP button, you can see PIP controller.
26) Select PIP channel.
27) Select PIP channel list : is used to change the PIP channel.
28) PIP Position : left bottom, left top, right bottom, light top
29) PIP size : small, normal, large
30) Toggle PIP program. : is used to swap the main channel and PIP channel.
31) PIP record. : is used to record the PIP channel while recording of main channel. If you have a single
tuner, you cannot see PIP record button.
32) Configuration/HELP
Basic controller
1) Start button: Is used to go to the first scene.
2) End button: Is used to go to the end of a scene.
3) Review button: Is used to search backward.
4) FF button: Is used to search forward.
5) Pause button: Is used to pause playing or replay.
6) Playback button: Is used to play an input signal (or file).
7) Stop button
8) Time-Shifting Button.
9) Favorites Channel : Add your favorite programs into favorite list before watching them.
10) Snapshot button: Is used for still image capture.
11) Instant Replay button: goes 10 sec backward by default. You can configure the instant replay time in
the configuration menu.
12) Record button : is used to configure the direct-record without dialog box in the configuration menu.
13) Mute button: Mute ON/OFF.
If you drag the mouse to the left bottom, window controller will be shown.
Windows controller
1 2 3 4 5 6 7
8 9 10 11 13 12

All specifications and information are subject to changes without further notices 20
4.3 Using FusionRemote
This indicates Remote Buttons.
4.3.1 Using For FusionHDTV
[ FusionHDTV IR Remote ]
Not only does it provide perfect control of all HDTV functions you will also be able to control Windows MCE
and many other application programs with this multifunctional remote control.
If you want to use detail usage, please download the latest software manual or refer to HELP in
advance. You can use Fusion Remote as the simple replacement of the keyboard. Press the profile button
on the remote transceiver for customizing the remote transceiver keys for the program you selected.
Volume Up/Down
SnapShot
As
p
ect Ratio
Mute
PC OFF
Record
Play/Pause/Stop
Rewind/Fast Forward
Toggle Display size
Numeric Key
File Open
DTV/ATV or LiveTV
Channel Up/Down
Instant Replay Instant Forward
Alt-Tab
Change Input Source
EPG/GUIDE
ProfileAPP start
Configuration
Go Previous channel
MCE DVD MENU
User Profile
PowerDVD Start
WinAMP Start
FusionHDTV Start
Direction/Enter
MCE Start/Exit