DVIGear DVI-7410 User manual
DVI-7410 EDID MANAGER
Quick Start Guide
Firmware version: 1.26
DVI IN (PC) Connector EDID manager's DVI input
Connect the DVI source to this connector
SOURCE CONNECTED LED
Indicates if the connected DVI source is powered
ON (detects presence of +5V signal on DVI IN
connector)
DVI SIGNAL DETECT LED Indicates if a live DVI signal is applied to DVI IN
connector ( detects TMDS Clock channel )
DVI OUT (MONITOR) EDID manager's DVI output connector
Connect to sink or display
MONITOR PRESENT LED Indicates if a monitor is attached to the DVI OUT
connector ( detects Hot Plug signal )
POWER LED Green if the EDID MANAGER is powered ON
BURN Button Reprograms the attached DVI Matrix switcher’s
input EDID data
LEARN Button Stores the attached monitor’s EDID data
Status LED Three color LED displaying the status of the EDID
Manager
GREEN Valid EDID data is selected by rotary switches
RED Empty memory or invalid EDID is selected
GREEN Flashing Burn or Learn has been effected successfully
RED Flashing Burn or Learn process failed
MEMORY ADDRESS Rotary switches for selecting one of 100 EDID
memories
9-12 VDC Power Connector Power input connector, center pin positive. The
connector is protected from reversed polarity.
DVI-7410 EDID MANAGER
Quick Start Guide
Firmware version: 1.26
Installation:
1. Connect the DVI source to the DVI IN (PC) connector.
2. Connect the monitor ( or sink device) to the DVI OUT connector.
3. Connect the AC adaptor to DC input and plug the adaptor to the power.
Now the unit is ready to use.
Selecting an EDID Value from Memory:
1. Turn the rotary switches to the desired memory address.
For example: X=1; Y=8: selected memory number is 18 )
2. The Status LED will turn to RED or GREEN.
If RED, an empty memory or invalid EDID data was selected.
If GREEN, valid EDID data is present at input.
Now the selected EDID is reported at DVI input.
Learning EDID Values:
1. Turn the rotary switches to the desired memory address where you
want to store the attached display's EDID.
2. Connect the display device to the EDID Manager's DVI output
which EDID will be stored ( monitor, projector, etc).
3. Press LEARN button for 2 seconds.
4. The status LED will flash RED or GREEN.
If flashing RED: the Learn process failed.
If flashing GREEN: the Learn process was successful.
Burning an EDID Value into DVI Matrix Switcher's EEPROM:
1. Connect the EDID manager's DVI OUT to a DVIGear DVI matrix
switcher's input which will be reprogrammed (only the connected
input will be reprogrammed, the others remain unchanged).
2. Select the desired EDID memory using rotary switches. If the status
LED turns GREEN, a valid EDID is selected.
3. Press BURN button for 10 seconds. Now the status LED turns orange.
During orange press and release rapidly the BURN button three times.
Now the EDID reprogramming process starts.
After burning the EDID, the status LED flashes RED or GREEN.
If flashing RED: the Burn process failed.
If flashing GREEN: the Burn process was successful.
Now the EDID has been changed at the connected Matrix Switcher’s input.
Factory Preset EDID List
Memory 00: Transparent EDID operation, the last attached monitor's EDID is
presented at the DVI input.
MEM Resolution MEM Resolution
01 640x480@60 Hz 26 1600x1200@50 Hz
02 640x480@75 Hz 27 1600x1200@60 Hz
03 848x480@60 Hz 16:9 28 1920x1200@60 Hz
04 800x600@50 Hz 29 1920x1200@50 Hz
08 1024x768@60 Hz 33 576i@50 Hz
09 1024x768@75 Hz 34 720x576p@50Hz
10 1152x864@75 Hz MAC 35 1280x720p@50 Hz
11 1280x768@50 Hz 36 1280x720p@60 Hz
12 1280x768@60 Hz 37 1920x1080i1@50 Hz
13 1280x768@75 Hz 38 1920x1080i2@50 Hz
14 1360x768@60 Hz 39 1920x1080i@60 Hz
15 1364x768@50 Hz 40 1920x1080p@24 Hz
16 1364x768@60 Hz 41 1920x1080p@25 Hz
17 1364x768@75 Hz 42 1920x1080p@30 Hz
18 1280x1024@50 Hz 43 1920x1080p1@50 Hz
19 1280x1024@60 Hz 44 1920x1080p2@50 Hz
20 1280x1024@75 Hz 45 1920x1080p@60 Hz
21 1366x1024@60 Hz 46 2048x1080p1@50 Hz
22 1400x1050@50 Hz 47 2048x1080p2@50 Hz
23 1400x1050@60 Hz 48 2048x1080p@60 Hz
24 1400x1050@75 Hz 49
25 1680x1050@60 Hz 50
Other DVIGear Receiver manuals
